Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Heating bath agitation and temp control?
How to agitate water heating bath at 60C? Do submersible pond pumps stand up to that temp? I use those pumps at lower temps with good results,
especially when cooling down a finished reaction when the bath water is replaced with cool water, but they might fail at too hot water. Max temps are
not available, as this sort of use is unheard of. Using additional overhead stirrer sounds a bit too heavy solution, but not out of the question.
Bubbler agitation with air pump could work, but it also multiplies the evaporation rate, unless the bath is enclosed. The goal here is to sustain a
stable bath temp up to 48 hours or more.
Also, do ordinary thermostats from eBay work with immersible water heaters?
|
|
Triflic Acid
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 486
Registered: 27-9-2020
Member Is Offline
Mood: Slowly Oxidizing into Oblivion
|
|
Well, for the first question, I would recommend an aquarium air bubbler at a low flow rate. As long as your tubing survives the temp, the actual
electronics are always kept at room temp. And what do you mean that max temperature use is unheard off? I thought everyone put aquarium pumps in their
tea kettles ![:P](./images/smilies/tongue.gif)
[Edited on 29-7-2021 by Triflic Acid]
There wasn't a fire, we just had an uncontrolled rapid oxidation event at the power plant.
|
|
ChemGlass
Harmless
Posts: 30
Registered: 9-7-2019
Member Is Offline
|
|
It's hard to picture your setup. I'm guessing to simply use a hot plate/mag stirrer won't work in this type of situations? I'm a little confused haha
Without fully understanding what your restrictions are, I have a few ideas off the top of my head. You could use a larger container for the heating
bath and buy something called a "sous vide". It's using for cooking but they clip onto the side of containers and have a programmable screen for
keeping the set temperature stable. I believe most of them also cause agitation in some way to circulate the water in the container you clip it onto.
It submerges slightly into the water. I've seen people use them before. I actually have one but I've never used it yet.
I think if you aren't able to use a hot plate stirrer in this situation, maybe buying a "sous vide" would substitute.
Maybe you could also look into a temperature controlled sonicator. You can get them pretty cheap on ebay and they work very well. I bought an old one
that has a digital screen on it and you can set the frequency of the sonication.
I can't tell if I'm missing the point here or I'm way off track with what you're trying to do. Does any of this seem viable with what you're up to? I
honestly think a heated sonicator would be a great option, but maybe this won't suit your application.
|
|
macckone
Dispenser of practical lab wisdom
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
sous vide:
https://www.amazon.com/Monoprice-Sous-Vide-Immersion-Cooker/...
It is basically two devices in one.
a hand blender: https://www.amazon.com/OXA-Smart-Powerful-Immersion-Blender/...
and a heater: https://www.amazon.com/Instant-Immersion-Electric-Portable-R...
with a thermostat
The one I posted is 800W, which is generally sufficient for non-distillation applications.
Down side is they usually are limited to 90 or 95C.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Sous vide immerser sounds like the perfect solution. Thanks for that a lot! The sous vide ready vessels are restricted of shape and size, but using
own bath vessel allows for perfect configuration. 800W should be enough, if the bath vessel is thermally insulated even if it's larger, and it
circulates the water. For upkeeping temps up to 90C I have used ikea induction plates, and I have to alter between stages 2 and 3, which are 250 ja
400W, respectively, so shooting constant 800W of heat will actually boil a kettle of water pretty quickly. The purpose is to have a bath that
principally buffers reaction temperature to desired temp, whether the reaction is exothermic, neutral or endothermic, within temp range of 40-100C. If
the immerser had a cooling mechanism too, it would be perfect. Now, the
immerser could likely be used as stirrer only, by using external cooling or heating source when needed.
For the record, I have permanently moved away from magstirs. They are unreliable, lack range and heating and stirring power, restrict the bath options
very significantly, basically to glass vessels of minimal size that the heating element usually can not sustain or it will burn out quickly, and are
prone to failure upon slightest solids appearance, and now that I tested that overhead work under vacuum as well, the final restriction lifted. Even
the cheapest of overheads allow for very effective agitation of even the more solids containing reactions under all circumstances.
Effective agitation of bath fluid at least multiplies the heating or cooling power. I have been able to run exothermic addition reactions much faster
when I have immersed an aquarium pump, and also when cooling reactions down, a hot water layer will quickly settle around a flask, stalling the
thermal gradient, but strong stirring keeps the liquid at constant heat transfer, and temps come down at least 2-4 times faster, if not even more.
From 90C to NTP it won't take too many minutes when replacing the bath water twice or thrice with new, 10C water.
Someone here had a signature stating that single most important vector at reaction is effective stirring. I'm beginning to believe in that.
|
|
karlos³
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Looks like the aquarium heating sticks I use to warm the water bath for yeast based reactions.
Those just cost a third or so of that, but they are usually "restricted" to a bit over 30°, I mean, you don't want to cook your fish... but I'm sure
someone technophilic enough could manipulate them easily and simply increase the possible temperature by a bit.
They can do that, they just shouldn't.
I know I had such a device malfunctioning, and had to keep my fish in buckets for two days, large ones even.
I think it reached over 40° and a few of the fish even died.
So it is definitely possible to crank them up if you know what you're doing.
The internal thermostat probably won't keep up with this, but thats what thermometers are for.
Of course, or pay thrice as much and buy the sous vide instead.
I would choose the latter, but technically I'm quite illiterate.
Quote: |
Someone here had a signature stating that single most important vector at reaction is effective stirring. I'm beginning to believe in that.
|
Nicodem, I think... or at least, the person has that quote from him in the signature ![:D](./images/smilies/biggrin.gif)
Its definitely true though.
[Edited on 30-7-2021 by karlos³]
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I ordered a 1500w 220V immersion heater just in case.
Personally, if I'm not into that specific business of converting fish cooking sticks to heat above 30C, I will just buy a thing that does the job. I
have had my fair share of sub-sub-sub-projects, and after procrastinating few years and ordering more and more all kinds of little trinkets from eBay
and wait 4-8 weeks to get my projects one step further (or fail for good) and never getting to actually do the real thing, which is chemistry and
reactions and synthesis, I just decided to invest the money needed to get good equipment designed for the very job I want them to do, and carry on
with my main hobby. Get a good insulated heating bath vessel, get an immersion heater stirrer with good thermostat control, get a 4-neck rbf with all
the required additional glassware like droppers, stillheads, thermowells etc and a stirrer adapter, and get an overhead stirrer with teflon paddle and
a flexible axial mount to make it run vibration free. With this setup, I can trust it to work when I want to do some reactions, and expect it to run
48 hours if necessary. ![:cool:](./images/smilies/cool.gif)
No any means to offend anyone who wants to configure equipment and DIY. I find it fascinating, but I don't have unlimited time so I want to use it as
efficiently as possible. I've been able to advance in my chemistry skills this last year more than the prior 10 combined, when I was just able to
fully focus on actual chemistry, not making sure all the tapes and screws held together. When I can confidently say that I can design and run a
synthesis based on basic data and end up with desired substance in pure, recrystallized form, I have achieved what I dreamed of.
|
|
karlos³
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1520
Registered: 10-1-2011
Location: yes!
Member Is Offline
Mood: oxazolidinic 8)
|
|
Absolutely understandable and I would have gone for macckones idea too ![:D](./images/smilies/biggrin.gif)
It might be an interesting idea for someone else though, so I posted it anways.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
So I got my immersion heater recently. Based on first test it seems like the best invention after overhead stirrer. It can be clamped on any vessel
that can withstand the required temp, it keeps temp at 0.1C accuracy between 0-100C with 1500W max power and it stirs the water decently and has max
timer of 99h with max 99h delay setting. This was the more expensive one, but the cheapest ones go for 20-40 bucks.
I'm planning on making a vessel from polyurethane sheets, same stuff that deschem&co uses to ship their glass, because it is extremely good
thermal insulator and is stiff and very cheap, a big sheet of 1.2x0.5m and like costs up from 5 bucks, bigger sheets less per sq m2. When a lid with
necessary holes for reactors and apparatus cut, the power needed to keep up the desired temp significantly decreases, compared to open vessel, that
can require significant horsepower to keep up the heat. It works both ways, a highly efficient cooling bath can be directly adapted, for which an
ordinary aquarium pump suffices for circulating the coolant body.
It can be easily cut to desired dimensions and assembled with glue and reinforced with tape, and if necessary, some rigid material to withstand larger
liquid bodies. Placing two or more of thick plastic bags into it will make it waterproof. Such vessel is also easy to adapt a drain valve to the
bottom, by simply punching a hole and screwing one tight, with backing plate and some silicone caulk if necessary. With this, when reaction is
complete, the bath can be immediately drained from hot water and replaced with cold water, effectively stirred, so the reaction temp can be brought
down in fast order.
|
|
Belowzero
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 173
Registered: 6-5-2020
Location: Member Is Offline
Member Is Offline
|
|
Quote: Originally posted by Fyndium ![](images/xpblue/lastpost.gif) | So I got my immersion heater recently. Based on first test it seems like the best invention after overhead stirrer. It can be clamped on any vessel
that can withstand the required temp, it keeps temp at 0.1C accuracy between 0-100C with 1500W max power and it stirs the water decently and has max
timer of 99h with max 99h delay setting. This was the more expensive one, but the cheapest ones go for 20-40 bucks.
I'm planning on making a vessel from polyurethane sheets, same stuff that deschem&co uses to ship their glass, because it is extremely good
thermal insulator and is stiff and very cheap, a big sheet of 1.2x0.5m and like costs up from 5 bucks, bigger sheets less per sq m2. When a lid with
necessary holes for reactors and apparatus cut, the power needed to keep up the desired temp significantly decreases, compared to open vessel, that
can require significant horsepower to keep up the heat. It works both ways, a highly efficient cooling bath can be directly adapted, for which an
ordinary aquarium pump suffices for circulating the coolant body.
It can be easily cut to desired dimensions and assembled with glue and reinforced with tape, and if necessary, some rigid material to withstand larger
liquid bodies. Placing two or more of thick plastic bags into it will make it waterproof. Such vessel is also easy to adapt a drain valve to the
bottom, by simply punching a hole and screwing one tight, with backing plate and some silicone caulk if necessary. With this, when reaction is
complete, the bath can be immediately drained from hot water and replaced with cold water, effectively stirred, so the reaction temp can be brought
down in fast order. |
I really like that idea, would you be so kind as to document the building and operation of such a device in it's own thread?
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I get my workspace by the fall, so if you are patient, I might actually give some details. The drain valve I was gonna use a simple sink discharge
outlet, since they fit directly to a suitable sized hole without any improvisation.
[Edited on 13-8-2021 by Fyndium]
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Styrofoam/expanded polystyrene insulated food boxes are cheap, waterproof and excellent insulators,
great for diy water baths, ice-water to almost boiling.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
You could get a plastic bucket, cut pail or any resistant container and then use either foam spray, plastic sheets (deschem packing type) or ceramic
oven insulation blankets to make the insulation on the outside of the pail/container.
A foam insulated pail like that can handle chemicals pretty well and have good thermal insulation.
The sous vide cooking devices have caught my interest too, but i would like a bit higher temps.
They seem quite nice though, heating with regulation and stirrer.
If the sous vide doesnt work there must be pumps that can withstand higher temps but are probably expensive.
Maybe a pump from a vehicle or other device that pumps hot liquid can be used.
I have bought this 250ml high-pressure thermal synthesis reactor that i would like to make a heater or heating block for.
I have thought about putting it into a heated oil-bath or in a oven but a aluminium heating block would be nice and no hot oil.
I could put several cartridge heaters in an aluminium block and let a PID temp controller with a SSR and temp probe heat the aluminium block and the
reactor.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
You will have some challenge finding non-metallic vessels that handle +100C. Hence, for any operations above 100C, I will just use a large SS kettle
with induction plate, which can easily handle temps to 200C and above, necessitating you have suitable bath media for it. Immersible heaters with
thermostat controller could deliver these temps, if induction plate would not be an option. If you are restricted to sub-1000mL flasks, you could do
with ordinary good grade stirplate, too. Sous-vide delivers out-of-box-all-inclusive appliance for 0-100C baths and is designed to run for two days
straight, so it's the ideal appliance for reliable reaction condition control.
I originally looked into having a separate box, insulation and other stuff, but as I'm a keen user of Occam's Razor, I want to find the ultimate
simple and idiot-proof solution, and as I have already used deschem boxes for cryogenic operations successfully, they have proven to be very
effective. The PU sheet is rigid, easy to cut and assemble, cheap and has one of the highest thermal insulation values of all insulating media.
|
|
|