electrokinetic
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 52
Registered: 6-6-2012
Location: Rhuidean
Member Is Offline
Mood: No Mood
|
|
Wrong/Bad Condensor with Soxhlet Extractor
I am looking to acquire a Soxhlet Extractor and found some on ebay that come with flasks and a condensor.
Listing 1
Listing 2
I don't have much experience with apparatus like this so I thought I'd ask: the first listing comes with a Graham condensor. But Grahams should be
avoided for reflux, yeah? So it's better to go with something like listing 2?
Thanks.
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I wonder it too why they sell graham condensers for reflux. I've tried it once, because that's what I got at hand then, and it almost ended up jumping
to trash bin by itself due to reflux choking it and causing pressure buildup. It was sheer luck I stood next to it when it choked and I just grabbed
it until it popped up.
Grahams are great for low boiling liquid condensers and post-coolers after primary condenser both for reflux and distillations, but never as reflux.
Soxhlet usually is supplied with Allihn condenser.
Dimroth or just coil condenser is my favorite all-purpose condenser. It has very large surface area and it also benefits from air-cooling of outer
wall so it is very hard to overrun, and it is also hard to choke and it can be used in any configurations possible. Acetone vapors came partially
through a liebig, but coil just condensed them all 1/3 way and had no issues when running it even a lot faster. I've got three of them, and have since
used my liebigs only when I needed to run multiple condensers for some reason.
[Edited on 4-3-2021 by Fyndium]
|
|
electrokinetic
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 52
Registered: 6-6-2012
Location: Rhuidean
Member Is Offline
Mood: No Mood
|
|
Dimroths are fantastic. I have one that is 19/22, and was hoping to find an appropriately sized Soxhlet to go with it. I found one, but it looks like the male and female ends are reversed. I would have no idea how to hook that up—I've never seen a boiling flask
with a male joint. Am I missing something simple?
[Edited on 4-3-2021 by electrokinetic]
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Just order adapter from China. Costs 4€.
|
|
electrokinetic
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 52
Registered: 6-6-2012
Location: Rhuidean
Member Is Offline
Mood: No Mood
|
|
That is pretty simple. Thanks.
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
what I did, ordered an adapter to 24/40 and used my Allihn @ 300mm for it, Now I have a Dimroth I'll be using that next run.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2692
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
You are correct that a Graham is not good for this type of use, it will limit your distillation rate severely.
The two links are also different sizes, the larger ones are often better as you can always use a large one with less material, but overloading one
will usually be a mess.
For people in the US, I still have these in small, medium, large and huge sizes, in US made glassware in used but very good condition. The prices
are similar to the chinese prices, but the quality is better.
|
|
zed
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Don't buy those sets, if you can help it. Think it out first.
I bought a Soxhlet set, dirt cheap a while back. 24/40 at the bottom of the reciever and 45/50 at the top. Then, I bought a 45/50 to 24/40 adapter
to mount a condenser. I used Deschem.
Here is the rational. The Graham Condenser is generally useless as a reflux condenser. Too small a bore, and too efficient. The condenser gets
plugged up with solvent, pressure builds up, and solvent blows out the top of the condenser. If you are working with something like Ether, this could
cause a fire and explosion.
Now, if you are working with the included Allihin, and you are refluxing water, that is fine. But, once again, if you are refluxing something like
Ether, there is danger. The Alihin is a good reflux condenser, but it is inefficient.
You will lose a lot of Ether as vapor. Explosive Vapor.
The top of the standard Soxhlet condenser, does not have a joint attached. Straight tube. That's it. You cannot back-up the Allihin, or use the
Graham for what it is good at....downward distillation.
If you can just buy the bottom half of the Soxhlet (cheap), and an adapter, you are better off. You will be completely free
to mix and match, as you like. You could use a 24/40 Allihin as your primary condenser, and fit a 24/40 Graham on top of it, as a scavenger. You can
also attach a 24/40 drying tube. Or, you can just use a much better condenser, like a 24/40 Friedrichs.
More versatile, is more better.
A friend chemist with Soxhlet problems, once blew up a building that way. Losing Ether, while conducting a reaction, under a Soxhlet. He attached a
long tube to the top of his (un-jointed) Soxhlet condenser to conserve solvent. It didn't work very well, he kept losing solvent. Eventually, the
reaction got hot, and he lost more solvent.
The reaction ran away. Pressure built up. Cooling the flask, did not help. It kept getting hotter. Vapor and Hydrogen gas, forced its way out of
the flask, and there was a very impressive detonation. He wasn't killed because he had wisely run for his life. But, it was a hairy, expensive mess.
And, the whole debacle might have been avoided, if he had been able to attach better condensers to his Soxhlet Extractor.
If you are American, 24/40 is standard here. In other parts of the World, 24/29 is more standard. They are somewhat compatible.... Usually. 24/40
is slightly more expensive.
Don't get stuck with a lot of stuff in odd sizes. An odd sized adapter, may cost more than the item it adapts to.
[Edited on 7-3-2021 by zed]
[Edited on 7-3-2021 by zed]
[Edited on 7-3-2021 by zed]
[Edited on 7-3-2021 by zed]
|
|
electrokinetic
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 52
Registered: 6-6-2012
Location: Rhuidean
Member Is Offline
Mood: No Mood
|
|
@Xeon thanks and good luck. I'd rather get one where I can use my dimroth (or my Friedrichs as well)
@zed solid advice thank you, I'll keep looking
|
|
XeonTheMGPony
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by electrokinetic ![](images/xpblue/lastpost.gif) | @Xeon thanks and good luck. I'd rather get one where I can use my dimroth (or my Friedrichs as well)
@zed solid advice thank you, I'll keep looking |
either way as said, get an adapter from the soxhlet to the size of ground joint you use was cheap and worked quite well
|
|
electrokinetic
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 52
Registered: 6-6-2012
Location: Rhuidean
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Dr.Bob ![](images/xpblue/lastpost.gif) | You are correct that a Graham is not good for this type of use, it will limit your distillation rate severely.
The two links are also different sizes, the larger ones are often better as you can always use a large one with less material, but overloading one
will usually be a mess.
For people in the US, I still have these in small, medium, large and huge sizes, in US made glassware in used but very good condition. The prices
are similar to the chinese prices, but the quality is better. |
I'm interested in checking out your wares. PM sent
|
|