Sciencemadness Discussion Board
Not logged in [Login ]
Go To Bottom

Printable Version  
 Pages:  1  ..  11    13    15  16
Author: Subject: Mystery Glassware Identification Thread
monolithic
Hazard to Others
***




Posts: 436
Registered: 5-3-2018
Member Is Offline

Mood: No Mood

[*] posted on 13-10-2020 at 12:23


Has anyone ever come across a 24/40 thermometer adapter with o-ring that can fit a 10 mm probe? It seems most 24/40 max out at around 5-7 mm. I found this https://www.wilmad-labglass.com/Products/LG-1451-306/ but $50 is a bit steep.

[Edited on 10-13-2020 by monolithic]
View user's profile View All Posts By User
itsallgoodjames
Hazard to Others
***




Posts: 276
Registered: 31-8-2020
Location: America Lite
Member Is Offline


[*] posted on 14-10-2020 at 07:26


Quote: Originally posted by monolithic  
Has anyone ever come across a 24/40 thermometer adapter with o-ring that can fit a 10 mm probe? It seems most 24/40 max out at around 5-7 mm. I found this https://www.wilmad-labglass.com/Products/LG-1451-306/ but $50 is a bit steep.

[Edited on 10-13-2020 by monolithic]


I have a distillation adaptor that has space for a 10mm thermometer. I bought it from deschem. One of those with a stopper where the condenser might work, depending on what you're doing. I'll get the link to it if you want




Nuclear physics is neat. It's a shame it's so regulated...

Now that I think about it, that's probably a good thing. Still annoying though.
View user's profile View All Posts By User
monolithic
Hazard to Others
***




Posts: 436
Registered: 5-3-2018
Member Is Offline

Mood: No Mood

[*] posted on 14-10-2020 at 14:05


Quote: Originally posted by itsallgoodjames  
Quote: Originally posted by monolithic  
Has anyone ever come across a 24/40 thermometer adapter with o-ring that can fit a 10 mm probe? It seems most 24/40 max out at around 5-7 mm. I found this https://www.wilmad-labglass.com/Products/LG-1451-306/ but $50 is a bit steep.

[Edited on 10-13-2020 by monolithic]


I have a distillation adaptor that has space for a 10mm thermometer. I bought it from deschem. One of those with a stopper where the condenser might work, depending on what you're doing. I'll get the link to it if you want


If it's not too much trouble can you find the link? I have a deschem 24/40 thermometer adapter but it maxes out at around 7.40 mm.
View user's profile View All Posts By User
Dr.Bob
International Hazard
*****




Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline

Mood: No Mood

[*] posted on 15-10-2020 at 17:16


I have at least two types of 24/40 adapters which should work with 10 mm tubes or trherms. I would sell them for $15. One is an Ace brand therm adapter but with a 10 mm #11 inlet adapter, the other is an all PTFE one with a red GL type 10 mm adapter on top. Let me know if you are interested, postage would be about $3-4 in the US.
View user's profile View All Posts By User
itsallgoodjames
Hazard to Others
***




Posts: 276
Registered: 31-8-2020
Location: America Lite
Member Is Offline


[*] posted on 20-10-2020 at 03:12


Quote: Originally posted by monolithic  
Quote: Originally posted by itsallgoodjames  
Quote: Originally posted by monolithic  
Has anyone ever come across a 24/40 thermometer adapter with o-ring that can fit a 10 mm probe? It seems most 24/40 max out at around 5-7 mm. I found this https://www.wilmad-labglass.com/Products/LG-1451-306/ but $50 is a bit steep.

[Edited on 10-13-2020 by monolithic]


I have a distillation adaptor that has space for a 10mm thermometer. I bought it from deschem. One of those with a stopper where the condenser might work, depending on what you're doing. I'll get the link to it if you want


If it's not too much trouble can you find the link? I have a deschem 24/40 thermometer adapter but it maxes out at around 7.40 mm.


The listing I bought it from seems to now be down (not surprising given I bought it over a year ago), I'll see if its been listed again under a different link




Nuclear physics is neat. It's a shame it's so regulated...

Now that I think about it, that's probably a good thing. Still annoying though.
View user's profile View All Posts By User
itsallgoodjames
Hazard to Others
***




Posts: 276
Registered: 31-8-2020
Location: America Lite
Member Is Offline


[*] posted on 20-10-2020 at 03:22


Quote: Originally posted by itsallgoodjames  
Quote: Originally posted by monolithic  
Quote: Originally posted by itsallgoodjames  
Quote: Originally posted by monolithic  
Has anyone ever come across a 24/40 thermometer adapter with o-ring that can fit a 10 mm probe? It seems most 24/40 max out at around 5-7 mm. I found this https://www.wilmad-labglass.com/Products/LG-1451-306/ but $50 is a bit steep.

[Edited on 10-13-2020 by monolithic]


I have a distillation adaptor that has space for a 10mm thermometer. I bought it from deschem. One of those with a stopper where the condenser might work, depending on what you're doing. I'll get the link to it if you want


If it's not too much trouble can you find the link? I have a deschem 24/40 thermometer adapter but it maxes out at around 7.40 mm.


The listing I bought it from seems to now be down (not surprising given I bought it over a year ago), I'll see if its been listed again under a different link


https://www.ebay.com/itm/231059351282

This looks like it *might* be it, it looks the same and is from the same seller, but it is a different listing, so it might not be. It does look pretty much identical to the listing I bought it from though.




Nuclear physics is neat. It's a shame it's so regulated...

Now that I think about it, that's probably a good thing. Still annoying though.
View user's profile View All Posts By User
Dr.Bob
International Hazard
*****




Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline

Mood: No Mood

[*] posted on 20-10-2020 at 07:55


Most thermometer adapters are designed to handle 5-6 mm and that is about it, the hole might be 7mm, but that would be hard to seal well. Ace sells many adapters for various diameters, including one for 10-11 mm, which is also the diam of most glass stir shafts (not counting the cheap ones from China).
View user's profile View All Posts By User
Clear_horizons_glass
Harmless
*




Posts: 42
Registered: 30-9-2019
Location: Pullman, WA
Member Is Offline

Mood: Glass

[*] posted on 26-11-2020 at 00:35


Hey, yall.
Is this a chromatography column with hooks on top for some reason, or is this some kind of vacuum adapter or filtration adapter?


[Edited on 26-11-2020 by Clear_horizons_glass]

[Edited on 26-11-2020 by Clear_horizons_glass]




Clear Horizons Laboratory Glassblowing Services
-------------------------------------------------------------
www.clearhorizonsglass.com
Phone and Fax:
(855) LAB-GLAS
(855) 522-4527
Have a glass project you want made? email me at
info@clearhorizonsglass.com
or message us here |
with a U2U |
message |
\/
View user's profile Visit user's homepage View All Posts By User
Clear_horizons_glass
Harmless
*




Posts: 42
Registered: 30-9-2019
Location: Pullman, WA
Member Is Offline

Mood: Glass

[*] posted on 26-11-2020 at 00:45


Also, what would you call this?
Adapter?

[Edited on 26-11-2020 by Clear_horizons_glass]




Clear Horizons Laboratory Glassblowing Services
-------------------------------------------------------------
www.clearhorizonsglass.com
Phone and Fax:
(855) LAB-GLAS
(855) 522-4527
Have a glass project you want made? email me at
info@clearhorizonsglass.com
or message us here |
with a U2U |
message |
\/
View user's profile Visit user's homepage View All Posts By User
ArbuzToWoda
Hazard to Self
**




Posts: 98
Registered: 15-7-2020
Member Is Offline


[*] posted on 26-11-2020 at 01:01


Some call it "koń" where I live, so a horse. But I doubt that applies to other countries!
View user's profile View All Posts By User
Fyndium
International Hazard
*****




Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline


[*] posted on 26-11-2020 at 08:11


Ground joint valve adapter? That's what chinese would write when listing it on ebay.
View user's profile View All Posts By User
Dr.Bob
International Hazard
*****




Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline

Mood: No Mood

[*] posted on 26-11-2020 at 11:18


I would guess that it is a way to hold down a gas inlet (often an inlet with a variable stopcock release to control the pressure on the flash column.) so it does not blow off under pressure. But you rarely see them on a column with a vacuum adapter, as you normally use only pressure or vacuum. Might be meant to allow some sort of liquid feed adapter to be held to the top while vacuum is applied. Not sure of any specific name.
View user's profile View All Posts By User
yobbo II
National Hazard
****




Posts: 764
Registered: 28-3-2016
Member Is Offline

Mood: No Mood

[*] posted on 3-12-2020 at 18:00


Quote: Originally posted by yobbo II  
Hi,
What is this item. It simply looks like a stopper with a handle. There is no access to the inside of the stopper and 'handle'.

This was posted 6 - 11- 19 my myself btw


Yob


I see a similar item on ebay.
Called 2 x QUICKFIT B24/29 "SHONIGEER" STOPPERS , HOLLOW BLOWN {CHEMISTRY} BRITAIN

2 x QUICKFIT B24/29 "SHONIGEER" STOPPERS, (ALSO USED IN IODINE FLASKS) HOLLOW BLOWN {CHEMISTRY} MADE IN BRITAIN

https://www.ebay.co.uk/itm/2-x-QUICKFIT-B24-29-SHONIGEER-STO...

YOB

[Edited on 4-12-2020 by yobbo II]
View user's profile View All Posts By User
SuperOxide
Hazard to Others
***




Posts: 487
Registered: 24-7-2019
Location: Devils Anus
Member Is Offline


[*] posted on 20-12-2020 at 07:20


Anyone know what this thingy is?


It looks like it's maybe a bubbler (or scrubber) with a suck back trap all in one piece of glassware? Perhaps you just put the liquid in the right part which can act as a bubbler or even scrubber, and if the reaction causes some negative pressure (suck back), the liquid would go into the part on the left as opposed to into the reaction vessel, then when the reaction starts generating pressure again, the liquid in the left part will get pushed back into the right part, maybe? What do you think?

P.S. I found that photo while scrolling through this amazing chemistry photo portfolio, which I found in someones signature here on SM. If any of you haven't seen that page (or the homepage of the same site), I definitely recommend spending some time scrolling through it. I had no idea chemistry could be so insanely gorgeous.

[Edited on 20-12-2020 by SuperOxide]
View user's profile View All Posts By User
electrokinetic
Hazard to Self
**




Posts: 52
Registered: 6-6-2012
Location: Rhuidean
Member Is Offline

Mood: No Mood

[*] posted on 4-1-2021 at 17:10


These pieces and others like it were donated to my classroom. I've never seen glassware that connects together this way, and I'm hoping someone can tell me what this connection style is called so I can research it.

IMG_2294.JPG - 1.7MB IMG_2293.JPG - 2.1MB IMG_2290.JPG - 1.8MB

[Edited on 5-1-2021 by electrokinetic]
View user's profile View All Posts By User
pneumatician
Hazard to Others
***




Posts: 412
Registered: 27-5-2013
Location: Magonia
Member Is Offline

Mood: ■■■■■■■■■■ INRI ■■■■■■■■■■ ** Igne Natura Renovatur Integra **

[*] posted on 22-1-2021 at 15:08


WTF is this?

uses??

https://www.ebay.de/itm/Industrie-Hochleistungs-Kolonne-Full...
View user's profile View All Posts By User
Chemetix
Hazard to Others
***




Posts: 376
Registered: 23-9-2016
Location: Oztrayleeyah
Member Is Offline

Mood: Wavering between lucidity and madness

[*] posted on 23-1-2021 at 13:58


Part of a short path distillation apparatus. A Kugelrohr.

https://www.jkem.com/product/kugelrohr-short-path-distillati...
View user's profile View All Posts By User
unionised
International Hazard
*****




Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline

Mood: No Mood

[*] posted on 7-3-2021 at 05:26


I was surfing eBay and came across this. The description is "Distillation apparatus reflux Quickfit CB11ND4X"
https://www.ebay.co.uk/itm/Distillation-apparatus-reflux-Qui...


Glass thing.JPG - 54kB

Any suggestions?
View user's profile View All Posts By User
Sulaiman
International Hazard
*****




Posts: 3721
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline


[*] posted on 7-3-2021 at 05:46


I don't know what it is but I want one!

I think that it is a part of this apparatus https://youtu.be/fMwFxUQx1PI




CAUTION : Hobby Chemist, not Professional or even Amateur
View user's profile View All Posts By User
unionised
International Hazard
*****




Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline

Mood: No Mood

[*] posted on 7-3-2021 at 08:35


Quote: Originally posted by Sulaiman  
I don't know what it is but I want one!

I think that it is a part of this apparatus https://youtu.be/fMwFxUQx1PI

Well there are two on ebay...

The last time I saw anything like it the caption said "The glassblower had hiccups".

[Edited on 7-3-21 by unionised]
View user's profile View All Posts By User
vano
National Hazard
****




Posts: 661
Registered: 22-3-2019
Location: Georgia
Member Is Offline


[*] posted on 3-7-2021 at 23:46



What is this?

received_113126587500049.jpeg - 204kB




View user's profile View All Posts By User
SWIM
National Hazard
****




Posts: 970
Registered: 3-9-2017
Member Is Offline


biggrin.gif posted on 4-7-2021 at 02:28


Quote: Originally posted by Sulaiman  
I don't know what it is but I want one!

I think that it is a part of this apparatus https://youtu.be/fMwFxUQx1PI


Well I'd buy one as long as it makes that sound.

Besides, it might come in handy for the co-polymerization of amino-acid residues and carbohydrate molecules, both containing ionic groups.:D

It should be perfectly simple if I can gt the heavy hydrogen, and maybe a bit of radioactive thorium.






[Edited on 4-7-2021 by SWIM]

Congressman-Estes-Kefauver-1948.jpg - 65kB

[Edited on 4-7-2021 by SWIM]




View user's profile View All Posts By User
Dr.Bob
International Hazard
*****




Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline

Mood: No Mood

[*] posted on 8-7-2021 at 16:49


Electokinetic,

They appear to be reservoirs for chromatography columns to me. You can screw them to the top of a colum to hold solvent, then either use gravity or air pressure to move the solvent through the column.
View user's profile View All Posts By User
Konduktor
Harmless
*




Posts: 7
Registered: 9-4-2021
Member Is Offline

Mood: Stressed & Depressed ®

[*] posted on 13-7-2021 at 13:09


Hi there,
Came across this strange piece when looking for glassware on my local auction site. Could anyone identify this mysterious part?



Cheers!
View user's profile View All Posts By User
barbs09
Hazard to Others
***




Posts: 113
Registered: 22-1-2009
Location: Australia
Member Is Offline

Mood: No Mood

[*] posted on 25-8-2021 at 01:43
Crucible with a perforated base


I have a small ceramic crucible with a perforated base. Maybe it is designed to heat/react something until a molten phase can exit the base? Ant thoughts? Thanks AB

20210810_205629.jpg - 3MB 20210810_205635.jpg - 3.3MB
View user's profile View All Posts By User
 Pages:  1  ..  11    13    15  16

  Go To Top