p4rtridg3
Harmless
Posts: 24
Registered: 28-1-2020
Location: Eastern United States
Member Is Offline
|
|
Anhydrous AlCl3 from Dean-Stark apparatus?
I'm pretty new to using dean-stark traps, and I'm wondering, could a toluene-water (or similar) immiscible azeotrope be exploited to dehydrate
aluminum chloride hexahydrate for Friedel-Crafts reactions? Why or why not?
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
No, because the water is chemically bonded.
The ligands are not as free as in a normal hydrate.
Upon heating it releases HCl and converts to the hydroxide.
[Edited on 9-11-2020 by macckone]
|
|
|
Cou
National Hazard
Posts: 958
Registered: 16-5-2013
Member Is Offline
Mood: Mad Scientist
|
|
I think you would end up with a suspension of aluminum hydroxide in toluene.
https://en.wikipedia.org/wiki/Aluminium_chloride#Reactions_w...
|
|
|
Texium
Administrator
Posts: 4580
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
Probably some kind of aluminum hydroxide/basic aluminum chloride mixture. It is a common misconception that compounds such as AlCl3
FeCl3 etc are structurally related to their hydrates. I think that it is misleading nomenclature to describe aluminum chloride hexahydrate
as AlCl3(H2O)6 because AlCl3 is actually a covalent compound (technically a dimer,
Al2Cl6) while the hexahydrate contains aluminum ions coordinated to 6 water molecules, in an octahedral formation, with three
chloride counterions. It would more accurately be written as Al(H2O)63+ + 3 Cl-
Saying that "AlCl3" is the anhydrous version of "AlCl3(H2O)6" is about as unhelpful and inaccurate as
saying that acetic anhydride is the anhydrous version of acetic acid. There may be a difference in their formulas that corresponds to the loss of
water, but they are fundamentally different compounds.
As I said about FeCl3 in another thread, while I know there's no hope of it catching on, I think using different names for these two very
different compounds would go a long way towards helping people appreciate the difference. I personally prefer aluminum trichloride among the accepted
names, since it sounds more covalent than just aluminum chloride, but why not go farther and call it trichloroaluminum, or hexachlorodialuminum to
completely distance it from salty naming conventions? Similar names are accepted for boron analogs. But I digress.
|
|
|
p4rtridg3
Harmless
Posts: 24
Registered: 28-1-2020
Location: Eastern United States
Member Is Offline
|
|
Quote: Originally posted by Texium (zts16)  | It is a common misconception that compounds such as AlCl3 FeCl3 etc are structurally related to their hydrates. I think that it
is misleading nomenclature to describe aluminum chloride hexahydrate as AlCl3(H2O)6 because AlCl3 is
actually a covalent compound (technically a dimer, Al2Cl6) while the hexahydrate contains aluminum ions coordinated to 6 water
molecules, in an octahedral formation, with three chloride counterions. It would more accurately be written as
Al(H2O)63+ + 3 Cl-
Saying that "AlCl3" is the anhydrous version of "AlCl3(H2O)6" is about as unhelpful and inaccurate as
saying that acetic anhydride is the anhydrous version of acetic acid. There may be a difference in their formulas that corresponds to the loss of
water, but they are fundamentally different compounds. |
Fascinating! I was unaware that they were different compounds.
I suppose I'll go looking for a source of anhydrous aluminum chloride then. And if necessary, I can always burn a piece of Al foil in dry chlorine.
|
|
|
Bubbles
Harmless
Posts: 31
Registered: 13-7-2020
Member Is Offline
|
|
I like aluminium trichloride, I will start calling it that from now on.
|
|
|
Bromide
Harmless
Posts: 24
Registered: 20-6-2007
Location: Flavor country
Member Is Offline
Mood: No Mood
|
|
| Quote: | | Quote: Originally posted by Texium (zts16) | ...
Saying that "AlCl3" is the anhydrous version of "AlCl3(H2O)6" is about as unhelpful and inaccurate as
saying that acetic anhydride is the anhydrous version of acetic acid. There may be a difference in their formulas that corresponds to the loss of
water, but they are fundamentally different compounds.
As I said about FeCl3 in another thread, while I know there's no hope of it catching on, I think using different names for these two very
different compounds would go a long way towards helping people appreciate the difference. I personally prefer aluminum trichloride among the accepted
names, since it sounds more covalent than just aluminum chloride, but why not go farther and call it trichloroaluminum, or hexachlorodialuminum to
completely distance it from salty naming conventions? Similar names are accepted for boron analogs. But I digress. |
Hear, hear. As in the name “sodium tetrahydridoborate” / “sodium borohydride” for NaBH4. |
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
