Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
Polypropylene funnel considerations
So the first time I used it, like an idiot, I broke my one glass funnel!
Now, all I have is this plastic (I think polypropylene?) funnel. My question is, can I use it to filter a hydrochloric acid containing solution?
Specifically, I am thinking of following the wiki's synthesis procedure for salicylic acid which requires 10% HCl solution. Can I pour this through my
funnel, what can / can't I use with it?
Thanks for the help.
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
Sulaiman
International Hazard
Posts: 3663
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Online
|
|
Polypropylene and polyethylene are surprisingly inert,
The only problems that I've had are stains and heat damage.
Dilute HCl is definitely OK.
Strong oxidisers and some solvents could be a problem but the contact is so brief that any damage is negligible,
So you can consider polypropylene or polyethylene funnels safe with all common liquids.
In general, Google "polypropylene chemical compatibility"
or substitute any other substance for "polypropylene"
[Edited on 5-6-2020 by Sulaiman]
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
OK, thanks.
I looked at a compatibility table, but it was for exposure over a 48 hour period, so it did not provide a very accurate picture. I figured that, in
this case, practical lab experience was probably better than abstract tables (as useful as they can be.)
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
Refinery
Hazard to Others
Posts: 371
Registered: 17-2-2014
Member Is Offline
Mood: Still
|
|
I haven't yet faced a chemical that eats polyethene at NTP, and not quite sure about polypropene either. Even styrene is stated to be not compatible
with PE, but a container I have has PE cap on it without any additional seals and it just sits there forever, so it can't be that bad. I've used PE
siphon to transfer 98% H2SO4, 35% HCL, ammonia solution, NaOH and practically all solvents and never had an issue.
Biggest issue with plastic funnels is staining like said. They get stained easily and are difficult to clean, so if you are doing amateur chemistry,
trace contamination should not be an issue in general.
|
|
RedDwarf
Hazard to Others
Posts: 166
Registered: 16-2-2019
Location: UK (North West)
Member Is Offline
Mood: Variable
|
|
I generally assume if I can't remove a stain, then it's also unlikely to contaminate anything either.
|
|
Refinery
Hazard to Others
Posts: 371
Registered: 17-2-2014
Member Is Offline
Mood: Still
|
|
Well there's that, too. I've got some parts that are contaminated by carbon, but it basically doesn't react with anything under 600C, so it really
doesn't matter.
|
|
Chemorg42
Hazard to Others
Posts: 103
Registered: 12-11-2019
Member Is Offline
Mood: Concentrated
|
|
98% H2SO4?
Wow, that is impressive.
Nitric acid is not compatible, though, correct?
Anyone who is not shocked by quantum theory has not understood a single word. (attributed to Niels Bohr)
I think I can safely say that nobody understands quantum mechanics. (Richard Feynman)
|
|
CouchHatter
Hazard to Others
Posts: 152
Registered: 28-10-2017
Location: Oklahoma
Member Is Offline
Mood: 76 elements taken!
|
|
I've used mine with 52% nitric acid and not noticed any staining. I also poured 40 mL sulfur chloride through one and it almost completely swole the
stem shut in seconds. Not going to use that one for much else.
|
|
Refinery
Hazard to Others
Posts: 371
Registered: 17-2-2014
Member Is Offline
Mood: Still
|
|
Polyethene and other same group stuff in general needs superacids to react. Polyethene handles sulfuric acid in ntp like everyday - it's sold in it.
|
|
Mateo_swe
National Hazard
Posts: 528
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
For these situations its good to have some compability charts for plastics and chemicals.
Here is 2 that i have used.
Attachment: chemicalresistance.pdf (199kB) This file has been downloaded 342 times
Attachment: Plastics chemical resistance guide.pdf (1.6MB) This file has been downloaded 418 times
|
|