Pages:
1
2 |
khourygeo77
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 114
Registered: 2-1-2017
Member Is Offline
Mood: No Mood
|
|
Device that heats at around 40 degrees C?
Hello,
I need to make some experiments while having a temperature at around 40 degrees C. The experiments may take a few months of continous heat and I dont
want the temperature to be interrupted. (dont want the device to stop working after 1 or 2 months)
Can I do this without paying much?
I bought the following terrarium heater but it doesn't seem to work well
https://www.miscota.com/reptiles/lucky/rep-thermo-socket-can...
Any ideas?
Thanks!!
[Edited on 17-5-2020 by khourygeo77]
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
Temperature is going to depend on the energy demand of your system and heat loss both of the system and the heat source. (I other words, insulation
and ambient temperature.)
Incandescent light bulbs are commonly used for hatching chickens. My thoughts would be to play around with a simple resistance heater: maybe
cannibalise an electric blanket and experiment with a variable power supply and an equipment mock-up. You might also have some success with a water
bath and a submersible element with thermostat. That would give a bit of thermal mass which might be good. See suppliers fot tropical aquariums.
In NZ it is common for domestic water heaters to be located inside a cupboard. Often there are exposed copper pipes that stay warm. With a bit of
insulation ripping and some imagination you might already have a solution.
Like I said, depends on the demands of your setup.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
A well insulated large thermal mass helps to maintain a constant temperature.
Using a heater of just enough power also helps by minimising rate of change of temperature.
Some basic information on your requirements may help
e. g. Air or liquid, volume, allowable temperature range etc.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
monolithic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
https://www.briskheat.com/products/heaters/heating-tapes-and...
You can get knockoff versions of this on various websites. Connect it to a variac and dial in your temperature.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
everything depends on your experiment, do you need to keep at 40°C a 250ml beaker or an entire complex apparatus?
if it is something small you can use a styrofoam box, they insulate quite nicely, the thicker the walls the better, i use one for recrystallizations
and it takes many hours for a 250ml beaker to go from 100c to room temperature.
if you don't want to pay much in electricity you need a well insulated container, even 5w of heating can be more than enough if you got the right
insulation
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
khourygeo77
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 114
Registered: 2-1-2017
Member Is Offline
Mood: No Mood
|
|
I am going to make a closed system and experiment with a thermometer to see at what distance I get the 40 degrees C then insert tiny flasks there. The
heater will be the center of the circle and several flasks all around it. So you dont have to worry about the system. I just need a device that gives
off a heat of 40-45 degrees C without getting corrupted after continual use of a few months. I can take care of the rest.
[Edited on 17-5-2020 by khourygeo77]
|
|
Tsjerk
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
I used stackable plastic boxes in the past. I would put an aquarium heater between two boxes and fill the space with water. I would insulate the whole
thing with blankets.
|
|
khourygeo77
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 114
Registered: 2-1-2017
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by j_sum1 ![](images/xpblue/lastpost.gif) | Temperature is going to depend on the energy demand of your system and heat loss both of the system and the heat source. (I other words, insulation
and ambient temperature.)
Incandescent light bulbs are commonly used for hatching chickens. My thoughts would be to play around with a simple resistance heater: maybe
cannibalise an electric blanket and experiment with a variable power supply and an equipment mock-up. You might also have some success with a water
bath and a submersible element with thermostat. That would give a bit of thermal mass which might be good. See suppliers fot tropical aquariums.
In NZ it is common for domestic water heaters to be located inside a cupboard. Often there are exposed copper pipes that stay warm. With a bit of
insulation ripping and some imagination you might already have a solution.
Like I said, depends on the demands of your setup. |
About the light bulb, I tried working with them once however they stop working after a few weeks maximum. I can always put 2 in case 1 stops working
so I replace it while the temperature keeps going, but the problem is that installing 2 lamps will cause a temperature change whenever one stops
working and this isn't what I want..
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
40-45°C is not heat. It is a temperature.
The temperature you attain will be a function of the rate of heat input and heat loss from your system. The former is the wattage of your heating
element. The latter is related to insulation.
It still is not clear what you hope to accomplish. But one thing is certain, it will not be a closed system -- you are asking about heat input and
you will also have heat being lost.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
Quote: Originally posted by khourygeo77 ![](images/xpblue/lastpost.gif) | I am going to make a closed system and experiment with a thermometer to see at what distance I get the 40 degrees C then insert tiny flasks there. The
heater will be the center of the circle and several flasks all around it. So you dont have to worry about the system. I just need a device that gives
off a heat of 40-45 degrees C without getting corrupted after continual use of a few months. I can take care of the rest.
[Edited on 17-5-2020 by khourygeo77] |
so your idea is to put a heat source in a room, and flaks all around it at the distance where you can measure 40°C?
1) we are not in a vacuum, convection is a thing, temperature in a room is not a function of the distance from the heater.
2) your system is not closed, it's totally open lol, if it was closed every point in the system should reach a thermal equilibrium, that's why pretty
much everyone is telling you to use an insulated box, small volume with same temperature instead of infinite open system with a radial temperature
gradient.
ps https://www.ebay.com/itm/W1209-DC-12V-Digital-thermostat-Tem...
here you are, take a small 12v 5w incandescent tube, an insulated box and this thermostat (the cheapest thing china has to offer) and your problem is
solved.
[Edited on 17-5-2020 by Ubya]
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
khourygeo77
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 114
Registered: 2-1-2017
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Ubya ![](images/xpblue/lastpost.gif) | Quote: Originally posted by khourygeo77 ![](images/xpblue/lastpost.gif) | I am going to make a closed system and experiment with a thermometer to see at what distance I get the 40 degrees C then insert tiny flasks there. The
heater will be the center of the circle and several flasks all around it. So you dont have to worry about the system. I just need a device that gives
off a heat of 40-45 degrees C without getting corrupted after continual use of a few months. I can take care of the rest.
[Edited on 17-5-2020 by khourygeo77] |
so your idea is to put a heat source in a room, and flaks all around it at the distance where you can measure 40°C?
1) we are not in a vacuum, convection is a thing, temperature in a room is not a function of the distance from the heater.
2) your system is not closed, it's totally open lol, if it was closed every point in the system should reach a thermal equilibrium, that's why pretty
much everyone is telling you to use an insulated box, small volume with same temperature instead of infinite open system with a radial temperature
gradient.
ps https://www.ebay.com/itm/W1209-DC-12V-Digital-thermostat-Tem...
here you are, take a small 12v 5w incandescent tube, an insulated box and this thermostat (the cheapest thing china has to offer) and your problem is
solved.
[Edited on 17-5-2020 by Ubya] |
No, it is not about putting them in a room, but in something small. I don't care if heat escapes, I just need the heat to remain the same at the same
points.
For example, I used to put a terrarium heater before in an empty small gallon of water and cover it. The temperature was ~39 degrees all the time
inside the gallon whenever I tried to measure it except at the beginning.
Ok. I will buy a thermostat.
About the incandescent tube, it can remain functional for several months straight?
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
Quote: |
Can I do this without paying much? |
Quote: |
I don't care if heat escapes |
these two things are opposite of eachother, that's why i was heavily suggesting insulating the container. if you want to keep an open fish tank at
40°C you are going to need at least a 25w heating element, if you insulate it, 5w will suffice, cheaper on the electrical bill.
about the life span of an incandescent light bulb, they usually live 1000 hours give or take, so if you keep it on 24/7 it should last you 1 month.
something you could do is using a 24V light bulb and run it on 12V (remember to pick a higher wattage bulb in that case) so the filament won't be so
hot, it should last longer.
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
khourygeo77
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 114
Registered: 2-1-2017
Member Is Offline
Mood: No Mood
|
|
yeah I didn't specify. I am not paying electricity and I can use it all the time while having a fixed price to pay for it every month.
But isn't it common for a light bulb to stop working sometimes after a week if turned on permanently? Sometimes I used lamps that were supposed to
last 1000 hours but they lasted 100 hours instead and other times they would last more...
And how is it possible to use 24V light bulb and run it on 12V? You mean the socket should be on 12V?
|
|
mackolol
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 459
Registered: 26-10-2017
Member Is Offline
Mood: Funky
|
|
You can buy the cheapest electric kitchen hotplate. The stuff is super cheap and you can get variety of temperatures up to 500C. At the lowest setting
it should be like 40C.
Also, you can use terrarium heating pad, it should be around 40C and it works by emitting infra red radiation, here is an example:
https://www.wish.com/product/5e7c4b787303c03973181412?hide_l...
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2689
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Try an easy bake oven... or just a 40 watt bulb in a box.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
buy a bulb rated for 24v, and connect it to a 12v power supply.
the 24v bulb should have a wattage 4 times the amount you need, if you were using a 12v 5w bulb, you need a 24v 20w bulb, so you get the same power
output at half the voltage while running the filament colder, aka it lasts longer.
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
clearly_not_atara
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2725
Registered: 3-11-2013
Member Is Offline
Mood: Big
|
|
I know it's not a real answer but when I saw the thread title my first thought was "a cat"
IIRC they make therapeutic heating pads that will hold themselves to around 40 C though if you look at the specs. A typical hot tub is also kept at 40
C but that seems like too much expense.
|
|
Ubya
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
Quote: Originally posted by clearly_not_atara ![](images/xpblue/lastpost.gif) | I know it's not a real answer but when I saw the thread title my first thought was "a cat"
IIRC they make therapeutic heating pads that will hold themselves to around 40 C though if you look at the specs. A typical hot tub is also kept at 40
C but that seems like too much expense. |
oh you reminded me of constant temperature PTC heating elements, but i don't know if there are ones for 40°C
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Apparently this is cheep.
https://www.youtube.com/watch?v=3Y0ROuPGaxw
[Edited on 18-5-20 by unionised]
|
|
Heptylene
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 319
Registered: 22-10-2016
Member Is Offline
Mood: No Mood
|
|
A fan, an electric heater and a PID controller in an insulated box could do the trick. Even styrofoam would withstand the heat. For safety, pick a
heating element that only gets warm when run at 100 % duty cycle.
A safe, low power heating element can be a kitchen appliance which is run on 12 volts instead of 120 volts. E.g. a waffle mold. You would put the
waffle mold in the box, connect it to 12 V via relay controlled by the PID. The power at 12 volts will be 100 times less than at 120 volts.
|
|
Herr Haber
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
Got nothing to add except if you are looking for decent sized styrofoam boxes for free make friends with your local sushi shop.
They receive their fish in very neat boxes that close very well and if you break then you can just come the next day !
I'd have used an aquarium heater / mat too.
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
khourygeo77
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 114
Registered: 2-1-2017
Member Is Offline
Mood: No Mood
|
|
I thought aquarium heaters would be a good idea, but they dont get above 35 degrees C unfortunately... Or at least this is the case with those I
saw...
And Thanks everyone for the tips, I finally have many cheap & simple & effective options to choose between..
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1309
Registered: 26-7-2004
Location: Middle Earth
Member Is Online
Mood: A trace of hope...
|
|
I've done exactly this -- and it turned out the heat input from the fan alone was enough to heat the box to 40C.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
j_sum1
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 6256
Registered: 4-10-2014
Location: Unmoved
Member Is Offline
Mood: Organised
|
|
Quote: Originally posted by khourygeo77 ![](images/xpblue/lastpost.gif) | I thought aquarium heaters would be a good idea, but they dont get above 35 degrees C unfortunately... Or at least this is the case with those I
saw...
And Thanks everyone for the tips, I finally have many cheap & simple & effective options to choose between..
| Again, the temperature you get to is a function of insulation and ambient temperature.
Your aquarium heater might be rated to 35° but you won't get anywhere near that if you are heating up a gymnasium or an igloo.
On the other hand, if you stuff your heater in a shoebox and surround that thing with space-shuttle tiles you will get much higher than 35° because
you have input of heat energy and no easy way for that heat to go anywhere.
|
|
Mateo_swe
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 526
Registered: 24-8-2019
Location: Within EU
Member Is Offline
|
|
You could use one of those heating pads 120x120mm made for 3D-printer and use a temp controller.
They have the temp sensor already inside.
https://www.ebay.com/itm/120x120mm-120W-12V-KEENOVO-Silicone...
Or you can use one of those seedling heatmats that are used when sprouting stubborn seeds.
They usually go to about 30°C but if you put it in an enclosure you probably can get 40°C at least.
They are made to run 24/7 ie. all the time.
Or just a lamp. If in an enclosure it will get warm, you need to make outside air cool it a little.
Or just some nicrome/kanthal heating wire with a controller, or heating cable for outside drainage to prevent freezing.
So many possibilities.
|
|
Pages:
1
2 |