Psychedelic_Monkey
Harmless
Posts: 4
Registered: 12-11-2019
Member Is Offline
|
|
Corning PC-420 Transformer Replacement
I recently picked up a used PC-420 from ebay it was a 120v model, in my infinite wisdom after looking at the power connector I saw it read 240v.
Unfortunately this was just what the socket was rated for and after about 5 mins of use I smelt that lovely burnt electronics smell and the
transformer exploded.
I'm wondering if any of you guys know the specifications for the transformer or maybe have a broken hotplate lying around, I could not find any
information looking up the numbers on the side. The only marking I could read was "HD35-12:5 A".
Any help is appreciated.
Attachment: IMG_1997.HEIC (979kB)
This file has been downloaded 390 times
Attachment: IMG_1998.HEIC (881kB)
This file has been downloaded 381 times
Attachment: IMG_1999.HEIC (1MB)
This file has been downloaded 360 times
|
|
|
Sulaiman
International Hazard
Posts: 3695
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
Before repairing the stirrer ... does the heating part still work ?
You are using 230 Vac instead of 110 Vac for both the transformer AND the heaing element.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
|
Psychedelic_Monkey
Harmless
Posts: 4
Registered: 12-11-2019
Member Is Offline
|
|
I believe the transformer is required for the control circuitry for the heating element - so I cannot test if the heating mantle still works but the
transformer clearly blew.
|
|
|
RedDwarf
Hazard to Others
Posts: 166
Registered: 16-2-2019
Location: UK (North West)
Member Is Offline
Mood: Variable
|
|
Just test the continuity on the heating element, as Sulaiman says no point in replacing transformer if you've fried everything else as well.
|
|
|
Psychedelic_Monkey
Harmless
Posts: 4
Registered: 12-11-2019
Member Is Offline
|
|
Continuity is fine for each heating coil, I've checked pretty much every major component, I could only find a problem with the transformer.
|
|
|
Keftedes89
Harmless
Posts: 12
Registered: 3-12-2014
Member Is Offline
Mood: No Mood
|
|
Check your U2U. I can probably help if you are in the USA
|
|
|
G-Coupled
Hazard to Others
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
K
Transformers, much like heating elements, can be repaired/rewound.
Quite often worth it if it's an oddball/ancient transformer model that's not available off the shelf.
|
|
|
Psychedelic_Monkey
Harmless
Posts: 4
Registered: 12-11-2019
Member Is Offline
|
|
I'm still looking for the part if anyone has one.
|
|
|
Dr.Bob
International Hazard
Posts: 2733
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I'll keep a lookout, I have many parts for older Corning units, but not sure if I have any broken 420s, but I will look around for any.
|
|
|
Heptylene
Hazard to Others
Posts: 319
Registered: 22-10-2016
Member Is Offline
Mood: No Mood
|
|
Could you find an equivalent transformer? I assume the voltage outputs are pretty standard. I guess you'd have to deduce the voltage needed since the
transformer doesn't work anymore, or have someone look inside their working PC-420 and measure the voltage. Do you have a picture of the circuit
board?
|
|
|
G-Coupled
Hazard to Others
Posts: 287
Registered: 9-3-2017
Member Is Offline
Mood: Slightly triturated
|
|
Yeah - that'd be a potentially really helpful bit of knowledge - if someone with a PC-420 could kindly measure the voltage coming out of the
secondary windings of the transformer when it's in operation, then it would be trivial to work out its rating and possibly find a compatible generic
replacement.
If the burned-out transformer is a simple, common one like a 120V-12V single tap, then you should have lots of choices to replace it with.
[Edited on 23-4-2020 by G-Coupled]
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
