Pages:
1
2 |
Sidmadra
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 129
Registered: 17-2-2017
Member Is Offline
Mood: No Mood
|
|
Suggestions for glass joint-grease that won't get stuck after vacuum distillations?
I've tried a handful of grease products, silicone grease, petroleum jelly, and a few others I don't recall, and often I end up needing to break out my
blow torch to heat the joint to loosen it in order to separate the joint, which I strongly dislike doing doing after distilling something highly
flammable. I searched and saw 1 user here claiming that Lithium Grease has never gotten stuck on them, but I figured I'd make an open post before
spending any money.
In the past I had used PTFE joint-sleeves, but they are kind of expensive and a little bit fragile, being easily ripped if snagged by joint clips for
instance. Also, for them to work effectively they the joints need to be very clean, but the upside to them is that they offer no risk of
contamination.
What is the best grease that you've managed to find to solve this issue of joints being stuck?
|
|
monolithic
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 436
Registered: 5-3-2018
Member Is Offline
Mood: No Mood
|
|
Dow high vacuum grease works well and has never frozen my joints, but it's expensive. Check eBay for some old stock.
|
|
SWIM
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 970
Registered: 3-9-2017
Member Is Offline
|
|
Joint quality can be a big issue too with stuck joints.
Some joints stick a lot more.
I think it has to do with quality control problems on dressing the joints, but I've had much less trouble using glass from major American makers than
I have from Chinese glass. The exception to this in my experience would be Laboy, which seems to have some pretty good workmanship.
If a joint seems grabbier than usual I'll often grind it lightly with toothpaste to get the joint surfaces a little smoother.
It seems to help.
I use Dow silicone grease, but I don't bother unless things are going to be getting pretty hot. I usually just wet the joints with whatever solvent
the reaction is running in.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
They make some very thin Teflon sleeves that work well for vacuum work, but not cheap. I agree that Dow's is the best there is, I use it for most
stopcocks and vacuum joints, if I use anything. I also know that not using any grease works in most cases, if you don't have basic solutions.
Those are really bad for seizing joints. Good luck.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3634
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I have wrapped a few turns of ptfe plumbers tape around the male joint in a single tape-width winding,
it seems to seal well and be removeable.
I do not know how high a temperature would be usable as I've only used water:ethanol for this seal so far.
I would expect ptfe to be ok for anything up to oil bath tempertures.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
PTFE tape is a common method of sealing joints around here.works for most reactions.havent come across anything that ruins it yet.
|
|
Herr Haber
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
I use Teflon sleeves and like them a lot more than grease.
True, I never used brand or expensive grease like the ones suggested above.
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Teflon tape is fine for most cases, but will not hold a high vacuum as it is both slightly gas permeable, as well as not nearly as tightly sealing as
grease, which fills the tiniest gaps and scratches to get a much better vacuum than with teflon tape. But that only matters if you are below 1 mm of
Hg.
|
|
Sidmadra
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 129
Registered: 17-2-2017
Member Is Offline
Mood: No Mood
|
|
Teflon joint sleeves are useful but I've found that if the joint isn't totally clean and free of particulates/dust/dirt then a strong vacuum can be
hard to achieve. In such cases, a good grease is more user friendly because it can easily compensate for any kind of particulates. Joint sleeves would
be more preferable if I could find a reasonably cheap source of them. The last time I purchased them I had to pay $100 for 5 of them, and I had some
rip in the first couple days, just getting snagged on clips, or ripped when trying to pull them out of the flask-joint head. I see there are some
cheaper ones online now, but if anyone can suggest the cheapest place to get them, that'd be awesome.
I believe I tried PTFE plumbers tape before, different grades, including the non-gas permeable ones, but I don't think I've ever been able to get any
sufficient seal with them; maybe I'll try again sometime soon.
|
|
Herr Haber
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
True, you have to make sure the joints are clean but from what I have seen my sleeves actually make up for small imperfections in my Chinese
glassware.
On my Duran Rodaviss glassware I get the opposite effect: the joints are already perfect and adding a sleeve is counterproductive.
My biggest surprise comes from the prices and quality you all seem to get. It's not the first time I've seen reports like Sidmarta's.
I pay mine 1.34 Euros and most seem to last between half a dozen to a dozen uses even when used to distill acid.
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
rockyit98
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 283
Registered: 12-4-2019
Location: The Known Universe
Member Is Offline
Mood: no mood is a good mood
|
|
i think there are silicone bands that can use as a sealant for vacuum work .maybe you can make them by your self. it just act as a separator.
atmospheric pressure do the rest by pushing two joints together so no air can get in, like in Magdeburg hemispheres .
https://en.wikipedia.org/wiki/Magdeburg_hemispheres
"A mind is a terrible thing to lose"-Meisner
|
|
Steam
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 238
Registered: 25-3-2014
Location: Minnesota
Member Is Offline
Mood: Triple Point
|
|
Even you do shell out the money for the Dow grease, a tube will last for a LONG time. Less is more with Vac grease- I have seen a lot of people use it
like caulking. Also, just be aware, Dow HVG is super insidious and tends to travel and contaminate things around the lab. Its something to be aware of
if you are doing mid-to high end spectroscopy work. There was a joke in my old lab that "one day, years from now, the entire planet will be coated in
a monolayer of Dow High-Vac grease. It is funny because, at least around the lab, it is sort of true. :]
DISCLAIMER: The information in this post is provided for general informational purposes only and may not reflect the current law in your jurisdiction.
No information contained in this post should be construed as legal advice from the individual author, nor is it intended to be a substitute for legal
counsel on any subject matter. No reader of this post should act or refrain from acting on the basis of any information included in, or accessible
through, this post without seeking the appropriate legal or other professional advice on the particular facts and circumstances at issue from a lawyer
licensed in the recipient’s state, country or other appropriate licensing jurisdiction.
|
|
S.C. Wack
bibliomaster
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
Dow is not expensive at all compared to Krytox and Apiezon greases, but it has an officially short shelf life, IDK why. It seems fine.
|
|
eesakiwi
Harmless
Posts: 27
Registered: 10-8-2005
Member Is Offline
Mood: drawnout
|
|
Somebody on another website did some MSDS searching & found vacuum grease is the same as car battery terminal grease.
My local car place sells sachets of it & red/green fibre washers to protect car battery terminals. Its red grease.
The Hershell ( H-500 ?) version is Silicon grease & clear. $8 for 100gms.
[Edited on 22-11-2019 by eesakiwi]
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3634
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I changed to ptfe tape from automotive silicone grease because
my cheap (Chinese) glassware joints needed a lot of grease to fill the joints,
and at higher temperatures the grease would dribble out of the joints,
into the glassware, contaminating my experiments.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Fyndium
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
I tested lithium grease for glass joints because I have it laying around and it seems to work well. Only very little is needed, except for bad joints
which seem to take more and probably have issues with vacuum and higher temps when it dribbles out. I must test it out soon in real action and see how
it works.
I also got some pet jelly, just in case it comes handy in lubricating things.
[Edited on 3-8-2020 by Fyndium]
|
|
Heptylene
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 319
Registered: 22-10-2016
Member Is Offline
Mood: No Mood
|
|
Put more grease? Sometimes if you don't put enough grease, there will be some parts of the joint (top or bottom typically) were there is
glass-to-glass contact. This causes the joints to get stuck. Try applying the grease on the entire length of the joint.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I agree that Dow Silicone grease is fine, gives peaks around 0.0 in the NMR, but easy to remove with chromatography, there are fluoronated ones that
are also great, but as stated, they are costly. I have used tubes that were 20 years old, Dow grease is forever, and a single tube can last years if
not wasted. But any thick grease will work OK.
|
|
draculic acid69
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1371
Registered: 2-8-2018
Member Is Offline
|
|
How do you remove grease from the joints after your reaction? Wipe with tissue or detergent or solvent? What's the process?
|
|
Eddie Current
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 78
Registered: 25-7-2018
Member Is Offline
|
|
I find that detergents don't do much, so after a really good rinsing just wipe out any excess with a tissue. If you have decent joints on your kit
then you only need to smear it on the cone very thin, and when I am going to pull some decent vacuum in the system, then I usually apply a thin
coating around the rim of the joint.
PTFE sleeves are also good if you can get them.
|
|
TLutman
Harmless
Posts: 26
Registered: 13-10-2019
Member Is Offline
|
|
I’ve been using dielectric silicone grease with no issues. It’s readily available from most car parts stores
|
|
UC235
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Just a thorough wipe-down with paper towel for me. I'll use acetone or hexane if I need it cleaner.
|
|
dawt
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 74
Registered: 9-5-2016
Location: EU
Member Is Offline
Mood: fluorescent
|
|
![](https://www.neubert-glas.de/laborglas/onlineshop/i_Manschette_1221740964196-250x189/Griffbundhuelse-fuer-Normschliffe-S.jpg)
Y'all don't use these? The only thing I've ever used grease for are stopcocks and desiccators. I got like 6 of them 15 years ago and they're still
holding up brilliantly.
|
|
Chemetix
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 375
Registered: 23-9-2016
Location: Oztrayleeyah
Member Is Offline
Mood: Wavering between lucidity and madness
|
|
Getting rid of silicone grease is done with a bit of paper towel and some WD40 or similar. I've recently tried DMSO and a heat gun on a large (45/50)
joint. Apply a dab on the top rim and allow the dmso to penetrate, then heat gun and some tapping with a wooden dowel.
Get the joint hot in a bunsen flame and some paraffin wax on the rim and allow to penetrate, then a tiny spray of WD40 to really get the wax into the
joint. Several heating and cooling cycles with tapping can often get a stubborn joint apart.
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
That Dow Corning HVG is really expensive at some places, but I found it for $30/tube (5.3oz) here:
https://www.usalab.com/dow-corning-high-vacuum-grease/?actio...
I have this which seems to be pretty good if you want to try a smaller size - 2oz for $11. It's pure silicone grease and it seems exactly like the
grease I've cleaned off of ground glass and desiccator rims.
https://www.amazon.com/Trident-acc577-Silicone-Grease-2oz/dp...
|
|
Pages:
1
2 |