twelti
Hazard to Others
Posts: 217
Registered: 20-2-2019
Member Is Offline
|
|
Testing EM Sensitivities
Has anyone made up their own EM sensitivity testing machines? I saw one or two nice examples in SM, though they looked a bit difficult for someone
without access to a shop to make. I'm interested in simple-ish devices for at least relative testing of sensitivities for ES discharge and either
impact or friction (assuming for now that they are reasonably related).
For the latter, I could imagine a fairly simple device with 2 piece of micron sandpaper and a fixed weight on top, and the EM placed between, and
maybe a solenoid or other electromechanical device to pull the top piece of sandpaper, and count number of detonations.
Any suggestions/examples of DIY test rigs are welcome.
|
|
MineMan
National Hazard
Posts: 998
Registered: 29-3-2015
Member Is Offline
Mood: No Mood
|
|
I have an answer, but not one your probably want to hear...
I think your focusing too much on sensitivities and testing sensitivities. I say this after reading your posts. Nearly all of the EMs have published
data... except s9me of the primary’s and exotic ligands...
A hammer and motor and pestle I believe are enough, unless you intend to pitch an explosive to industry or write a scientific study...
|
|
twelti
Hazard to Others
Posts: 217
Registered: 20-2-2019
Member Is Offline
|
|
Yes, some of these substances that are off the beaten track maybe, an can't just be looked up. Also, so many ways to reduce (or increase) sensitivity
of a given substance. For example, I tried stearic acid and dextrine on that nickel AG perchlorate. Grinding in a mortar doesn't seem to show any
obvious difference but I'm guessing there is some. I guess I could focus on testing other explosive properties though. Lead expansion?
|
|
markx
National Hazard
Posts: 645
Registered: 7-8-2003
Location: Northern kingdom
Member Is Offline
Mood: Very Jolly
|
|
We should not forget that the vast published amount of data which exist for most compounds, although being accurate, verified and reliable, shall not
tell anything about the properties of the actual sample one is working with.
Therein may lie a grave pitfall, as without any sensitivity testing of the sample at hand we only assume that it has the claimed properties.
In reality the sample may be altered by side products or substances that can stem from any number of sources....contaminated chemicals, residue on
reactor vessels, unwanted reactions with tools or materials used in synthesis, misdosing, altered synthesis conditions, etc.
So one might end up working with a more sensitive sample than could be assumed based on generic reference and the only way to be sure is to conduct at
least some kind of assessment before further manipulations.
I agree, it does not have to be a sophisticated test with top quality equipment....a simple hammer blow can put things into perspective if one gathers
a bit experience and learns to read it correctly.
If one is more serious about the chosen field of research, then taking the time and effort to put together some "proper" testing gear is sure going to
help a lot. It shall give actual comparable quantitative data that can help the researcher to understand the effects and trendlines that varying
certain factors shall have upon the end result.
A weight drop frame with a height scale to measure impact sensitivity is very useful, a brisance cell to assess sand crush effect, any approach for
friction that works to give repeatable and comparable results. A melting point apparatus and electrical discharge tester are also immensely useful,
but might prove a bit more complicated to construct. Not impossible though....
Exact science is a figment of imagination.......
|
|
MineMan
National Hazard
Posts: 998
Registered: 29-3-2015
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by twelti | Yes, some of these substances that are off the beaten track maybe, an can't just be looked up. Also, so many ways to reduce (or increase) sensitivity
of a given substance. For example, I tried stearic acid and dextrine on that nickel AG perchlorate. Grinding in a mortar doesn't seem to show any
obvious difference but I'm guessing there is some. I guess I could focus on testing other explosive properties though. Lead expansion?
|
How much SA did you use? Surly 5 percent would make a difference in a mortar??
Graphite can help with friction and static too
|
|
twelti
Hazard to Others
Posts: 217
Registered: 20-2-2019
Member Is Offline
|
|
Quote: Originally posted by MineMan |
How much SA did you use? Surly 5 percent would make a difference in a mortar??
Graphite can help with friction and static too |
I wasn't too precise, maybe 3 %. I tried just tonight dissolving the SA in Etoh, and putting the NiAG Perchlorate in that. Now I overshot too far.
It is waxy and insensitive. Too much SA. It did work though, in a way. I want to try graphite too.
|
|