Iron Madara
Harmless
Posts: 10
Registered: 17-2-2019
Member Is Offline
|
|
safe powerful Nitroglycerin liquid mixtures ?
I read about some NG mixtures which are considerd to be desensitized.
according to this study if NG mixed with 30% acetone or 40% triacetene it will be greatly desensitized and become comparable with TATB !!
but I have some concerns regarding these mixtures :
does anyone tested similar mixtures ?
would mixing NG with raw glycerin give similar results ?
are they still powerful explosives ? would they be stronger than TNT for example ?
should they retain safety even with large diameters?
if such mixtures are safe and powerful why they are not widely used ?
[Edited on 5-3-2019 by Iron Madara]
|
|
|
greenlight
National Hazard
Posts: 753
Registered: 3-11-2014
Member Is Offline
Mood: Energetic
|
|
I have never heard of someone testing the sensitivity of NG in acetone. I have only seen acetone used to desensitize NG so that other chemicals
(sawdust/cornstarch/AN) can be mixed with it to manufacture dynamite.
It would be more powerful than TNT and my guess would be it would retain the same properties in small and large diameters.
Problems would be that it is a liquid explosive and you can still get migraines from handling it.
Overall, it doesn't meet the standards that are required by explosives nowadays, nitroglycerin has been slowly phased out as an explosive and nearly
all of NG that is made would be used in manufacture of propellants.
For mining, we want lower VOD explosives like ammonium nitrate mixtures and not brisant powerful ones that will break rock into too small pieces.
The military wants high energy, high density solid explosives that are easy to handle (PE's/PBX's) and non toxic if possible.
There's not much room left for liquid explosives anymore apart from maybe a few exotic uses, especially ones that are a headache to handle.
Be good, otherwise be good at it 
|
|
|
Microtek
National Hazard
Posts: 872
Registered: 23-9-2002
Member Is Offline
Mood: No Mood
|
|
If you consider adding acetone for desensitizing, be aware that it could evaporate from the mixture over time which would increase sensitivity. The
container doesn't have to be open for this to happen (if it is made of something that acetone can penetrate by diffusion).
|
|
|
Laboratory of Liptakov
International Hazard
Posts: 1405
Registered: 2-9-2014
Location: Technion Haifa
Member Is Offline
Mood: old jew
|
|
Manipulation with liquid nitro compounds and their use is difficult. Nitroglycerin is an outdated energy material. Like detonators from FHg. Just like
a steam engine... ...LL
Development of primarily - secondary substances CHP (2015) Lithex (2022) Brightelite (2023) Nitrocelite and KC primer (2024)
|
|
|
Iron Madara
Harmless
Posts: 10
Registered: 17-2-2019
Member Is Offline
|
|
Quote: Originally posted by Microtek  | | If you consider adding acetone for desensitizing, be aware that it could evaporate from the mixture over time which would increase sensitivity. The
container doesn't have to be open for this to happen (if it is made of something that acetone can penetrate by diffusion). |
but Triacetin is different, it has boiling point of 290°C. it is also easily prepared .
a mixture with only 25% Triacetin is considered safe for shipping:
http://www.copperheadchemical.com/Defense/NG_0208.pdf
|
|
|
Dornier 335A
Hazard to Others
Posts: 231
Registered: 10-5-2013
Location: Northern Europe
Member Is Offline
Mood: No Mood
|
|
Those mixtures are quite weak compared to other explosives of similar sensitivity. 30% acetone in NG lowers the detonation velocity from 7700 m/s to
about 5700 m/s and the detonation pressure from 270 to 130 kbar (calculated figures). This is weaker than PLX and a lot worse than TNT.
|
|
|
Laboratory of Liptakov
International Hazard
Posts: 1405
Registered: 2-9-2014
Location: Technion Haifa
Member Is Offline
Mood: old jew
|
|
Very interesting counting, Dornier. 130 kbar is really weak pressure. Is it pity use NG with huge diluting. Shortly, is it nonsense.
Development of primarily - secondary substances CHP (2015) Lithex (2022) Brightelite (2023) Nitrocelite and KC primer (2024)
|
|
|
pocoratbone
Harmless
Posts: 2
Registered: 24-6-2019
Member Is Offline
|
|
I have found an interesting way of neutralizing and desensitizing NG. After nitration and washing in cold water I dissolve it in acetone and then
crash this into sodium bicarbonate solution. I then allow the acetone to evaporate next to a fan. The NG will separate out and you can then remove via
sepratory funnel. Even though you will be unable to smell the acetone some still remains and is a desensitizer. I placed several drops on paper on
concrete floor and could not set it off no mater how many times I beat it with a hammer.
|
|
|
pocoratbone
Harmless
Posts: 2
Registered: 24-6-2019
Member Is Offline
|
|
I have found an interesting way of neutralizing and desensitizing NG. After nitration and washing in cold water I dissolve it in acetone and then
crash this into sodium bicarbonate solution. I then allow the acetone to evaporate next to a fan. The NG will separate out and you can then remove via
sepratory funnel. Even though you will be unable to smell the acetone some still remains and is a desensitizer. I placed several drops on paper on
concrete floor and could not set it off no mater how many times I beat it with a hammer.
|
|
|
MineMan
International Hazard
Posts: 1012
Registered: 29-3-2015
Member Is Offline
Mood: No Mood
|
|
Interesting. Can you estimate how much acetone is present? This would be really fantastic if soaked into AP for OB and density.
|
|
|
Microtek
National Hazard
Posts: 872
Registered: 23-9-2002
Member Is Offline
Mood: No Mood
|
|
Nitromethane is miscible with NG and is oxygen deficient and very insensitive. Mixtures of the two could be adjusted to required levels of performance
(more NG) or safety (more NM).
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
