Jackson
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 189
Registered: 22-5-2018
Location: U S of A
Member Is Offline
Mood: ![:)](./images/smilies/smile.gif) Happy about new glassware
|
|
Benzhydrol from Diphenhydramine
Hi, I have been looking to try and synthesize Benzhydrol from Diphenhydramine. It looks like Diphenhydramine is an ester of Diphenylmethanol
(Benzhydrol) and Dimethylethanolamine. I plan on using Either Sodium hydroxide or Sulfuric acid to perform this hydrolysis. My plan is to make a
solution of H2SO4 or NaOH and disolve pure freebase Diphenhydramine in it. After that I would reflux for a while. Then I would heat to evaporate the
DMEA and water. The crude Benzhydrol would then be recrystalized from isopropanol or methanol. Are there any problems with my route? I probably will
use NaOH because its probably not that good to try and evaporate off sulfuric acid.
|
|
Fantasma4500
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1681
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
if NH4OH would be able to dissolve it, you would be one step ahead in terms of purification
|
|
CuReUS
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 928
Registered: 9-9-2014
Member Is Offline
Mood: No Mood
|
|
this is a good way to get
benzhydrol from an OTC compound.Brilliant find Quote: | looks like Diphenhydramine is an ester of Diphenylmethanol (Benzhydrol) and Dimethylethanolamine. | its an
ether,not an ester Quote: | I probably will use NaOH because its probably not that good to try and evaporate off sulfuric acid. | NaOH
can't cleave ether,use H2SO4 only
[Edited on 19-1-2019 by CuReUS]
|
|
UC235
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 565
Registered: 28-12-2014
Member Is Offline
Mood: No Mood
|
|
Where would you get that much diphenhydramine to make this worthwhile? Unlike aspirin or acetaminophen, there's only 25mg per tablet and it's mostly
binders. Diphenhydramine HCl is 291.8g/mol and benzhydrol is 184.2g/mol. If you could get 100% recovery at every step, it would take 634 tabs to make
10g benzhydrol.
On the other hand, working out an OTC reduction of benzophenone would be a much better approach. The going rate for 100g already purified is about
$20.
|
|
Tellurium
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 84
Registered: 12-7-2017
Location: Group 16, Chalcogen City
Member Is Offline
Mood: smelly
|
|
Quote: Originally posted by UC235 ![](images/xpblue/lastpost.gif) | On the other hand, working out an OTC reduction of benzophenone would be a much better approach. |
I think urushibara nickel should be usable, shouldn't it? Because the preparation of it is quite OTC and it's claimed to also work great at
atmospheric pressure![:P](./images/smilies/tongue.gif)
[Edited on 19-1-2019 by Tellurium]
|
|
DavidJR
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Quote: Originally posted by Tellurium ![](images/xpblue/lastpost.gif) | Quote: Originally posted by UC235 ![](images/xpblue/lastpost.gif) | On the other hand, working out an OTC reduction of benzophenone would be a much better approach. |
I think urushibara nickel should be usable, shouldn't it? Because the preparation of it is quite OTC and it's claimed to also work great at
atmospheric pressure![:P](./images/smilies/tongue.gif)
|
I tried a handful of ways to reduce benzophenone to diphenylmethanol and my conclusion was that the easiest way by far was to use sodium borohydride.
It's also a surprisingly cost effective method because you really don't need much borohydride at all.
|
|
wakatutu
Harmless
Posts: 31
Registered: 23-2-2017
Member Is Offline
Mood: Mostly Harmless
|
|
http://www.orgsyn.org/demo.aspx?prep=cv1p0090
Looks like benzophenone can be reduced using zinc and sodium hydroxide in ethanol.
|
|
Jackson
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 189
Registered: 22-5-2018
Location: U S of A
Member Is Offline
Mood: ![:)](./images/smilies/smile.gif) Happy about new glassware
|
|
Honestly I only want the Benzhydrol for small scale synthesis so It still seems like a good option for me. Thanks for all the responses so far! I will
try it as soon as I get home from vacation. I do have on question remaning. Would Diphenhydramine be usable instead of the freebase? It just removes
one more step (freebasing) in which product could get lost.
[Edited on 1/20/2019 by Jackson]
|
|
AvBaeyer
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 646
Registered: 25-2-2014
Location: CA
Member Is Offline
Mood: No Mood
|
|
No need to free base it. If you use H2SO4 for the ether cleavage it will be a salt in solution anyway. However, I think that this is a crazy and
inefficient way to get benzhydrol - see UC235 above.
AvB
|
|
Jackson
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 189
Registered: 22-5-2018
Location: U S of A
Member Is Offline
Mood: ![:)](./images/smilies/smile.gif) Happy about new glassware
|
|
Yeah I know its just that I wanna explore the process. If i needed any for a large synth I would just make it from Benzophenone.
|
|
Mothman
Harmless
Posts: 42
Registered: 26-9-2017
Member Is Offline
Mood: Aminated
|
|
Quote: |
Where would you get that much diphenhydramine to make this worthwhile?
|
There is a generic benadryl brand for sale on amazon, 50 mg/pill, 1000 pills, and sold for 16 freedom bucks. Assuming 100% yield that's 50g of
diphenhydramine hydrochloride, which is a sizable amount at a low cost.
I actually attempted to extract from these pills about seven months ago, but I ran into some issues (my clumsiness eventually put the final nail in
the coffin for that experiment but I don't need to ask whether or not I should avoid knocking over my setup this time around). The first issue I ran
into was the gelatin capsule itself. I had planned to use distilled water as the solvent for the extraction (because I had no other solvents, calling
it a plan is a stretch) and so I decided I would manually cut open all thousand pills with pliers and sift off the heavily dyed (and water soluble)
gelatin fragments. The five hours this process took made my hands cramp to high hell (clearly my gloves were not compatible with repetitive motion
injuries ). My second issue was the "decision" to use water as the extraction
solvent in the procedure. These pills are full of binders that gummed up my filter paper very quickly. Since I didn't have much in the way of
equipment or chemicals, my solution to this was to wait a week for everything to filter through. After that week, everything had filtered through, and
I then proceeded to knock everything over on accident as I turned away from another project (should've put that in the "when chemistry goes wrong"
thread). I decided I would put this project on the backburner but I bought another bottle of pills for when I finally decided to try again. Apart from
effectively addressing my allergies, the pills haven't been put to much use and are gathering dust as I type this.
I think that now is a wonderful time to try this experiment again, and perhaps I can contribute something useful to this community that has helped me
on so many occasions, but I have some questions first:
1) Are there better solvents for extraction of DPH hydrochloride out there? I mean obviously there's always a better solvent but I mean in terms of
OTC solvents like methanol, ethanol, isopropanol, n-butanol, acetone, ethyl acetate, and methyl ethyl ketone. I have access to all of these solvents
but I do not know where to find literature detailing their suitability for this experiment, perhaps DPH hydrochloride solubility in various solvents
can be part of what I contribute to this forum's knowledge base if it isn't listed somewhere. In the meantime, help would be appreciated!
I guess my second question of whether or not "the solvent" is good enough that I can skip the pliers and go to the coffee grinder will be easily
answered once I know which solvent is "the solvent." Heck I could google gelatin solubility in all of the solvents listed but it's pushing 2:00 a.m.
here. If experimentation to determine an appropriate solvent is necessary I'm going to bet that isopropyl alcohol will give best results because I
always see that used for extraction of pharmaceutical hydrochloride salts, though I have no idea what the solubility of gelatin is within IPA.
After the DPH is extracted/purified I have one other question: Would HBr work to cleave the ether bond and form diphenylmethyl bromide in one step? I
plan to react benzhydrol with HBr anyways to experiment with the Grignard reaction but if it is possible to do this all in one step things would be
far simpler. I know that HBr cleaves ether bonds but the dimethylethanolamine side product is something I have no idea of the reactivity of in the
presence of HBr.
All information is appreciated, I look forward to finally being able to use that nice large pill bottle these capsules are in for storage of other
compounds!
Thank you!
You can be happy
|
|
CuReUS
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 928
Registered: 9-9-2014
Member Is Offline
Mood: No Mood
|
|
what about
dithionite ? Quote: Originally posted by Mothman ![](images/xpblue/lastpost.gif) |
Quote: |
Where would you get that much diphenhydramine to make this worthwhile?
|
There is a generic benadryl brand for sale on amazon, 50 mg/pill, 1000 pills, and sold for 16 freedom bucks. Assuming 100% yield that's 50g of
diphenhydramine hydrochloride, which is a sizable amount at a low cost. | exactly what I was going to say.You
can buy a shit ton of drugs online cheaply.Also,its not a watched drug so it shouldn't set any phones ringing. Quote: Originally posted by Mothman ![](images/xpblue/lastpost.gif) |
The first issue I ran into was the gelatin capsule itself. I decided I would manually cut open all thousand pills with pliers and sift off the heavily
dyed (and water soluble) gelatin fragments. The five hours this process took made my hands cramp to high hell. | Are there another brands that sell the tablet form ?
Quote: | 1) Are there better solvents for extraction of DPH hydrochloride out there? | Why do you have to extract it
at all ? Can't it be done similar to the shake n bake or krokodil method ?
Quote: | Would HBr work to cleave the ether bond and form diphenylmethyl bromide in one step? | yes ![:)](./images/smilies/smile.gif)
[Edited on 20-1-2019 by CuReUS]
|
|
Mothman
Harmless
Posts: 42
Registered: 26-9-2017
Member Is Offline
Mood: Aminated
|
|
Quote: |
Why do you have to extract it at all ? Can't it be done similar to the shake n bake or krokodil method ?
|
Ok, here are the ingredients on the capsule:
Black Iron Oxide
D&C Red No. 28
FD&C Blue No. 1
FD&C Red No. 40
Gelatin
Lactose Monohydrate
Magnesium Stearate
Silicon Dioxide
Sodium Lauryl Sulfate
So if by "Shake and Bake" you mean blending everything up and chucking in some sulfuric acid and water as compared to an iodine/phosphorous reduction
style deal...I was skeptical at first but this actually looks like it could work based on what would happen to a lot of these compounds in acidic
conditions. The benzhydrol would fall out of solution as it was formed and the extra crud would react away with the acid and then remaining solids
would be mostly benzhydrol and whatever happened to the gelatin present. Organic solvent extraction ought to be simple from that point forward and any
stearic acid produced could be removed via a lye wash of the final product...and if one wanted the dimethylethanolamine they could basify and distill
the remaining reaction mixture, or run an acid/base extraction...And I could always purify the benzhydrol before reacting with HBR, as this process
doesn't sound like too much of a hassle really.
I won't make the mistake of using all of my pills like I did last time, just 100 of them for a nice 5g of DPH hydrochloride in the starting material.
Question: Best water to acid ratio? I haven't used H2SO4 for ether hydrolysis before but I know it requires water to be present. Would it be best to
use dilute (10% w/w) sulfuric acid for this process or is a higher concentration needed?
I think I know what I'm going to be doing today ![:D](./images/smilies/biggrin.gif)
EDIT: Also I don't know if there are other brands, but determining if this brand is suitable should not take too long nor would it be too expensive.
If I have to I'll buy a different brand but this stuff is what I have.
[Edited on 20-1-2019 by Mothman]
You can be happy
|
|
Jackson
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 189
Registered: 22-5-2018
Location: U S of A
Member Is Offline
Mood: ![:)](./images/smilies/smile.gif) Happy about new glassware
|
|
Im trying to synthesize diphenylmethyl bromide from benzhydrol to use in the synthesis of a lignand. Could I just reflux sodium bromide, H2SO4, and
diphenhydramine HCL, then filter out the diphenyl methyl bromide and recrystalize from an alcohol to obtain a more pure product?
|
|
DavidJR
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Quote: Originally posted by Jackson ![](images/xpblue/lastpost.gif) | Im trying to synthesize diphenylmethyl bromide from benzhydrol to use in the synthesis of a lignand. Could I just reflux sodium bromide, H2SO4, and
diphenhydramine HCL, then filter out the diphenyl methyl bromide and recrystalize from an alcohol to obtain a more pure product?
|
That sounds reasonable to me...
Benzhydryl bromide is apparently not all that stable, however.
|
|
Mothman
Harmless
Posts: 42
Registered: 26-9-2017
Member Is Offline
Mood: Aminated
|
|
Quote: |
Benzhydryl bromide is apparently not all that stable, however.
|
What do you mean by unstable? Are there special storage conditions to meet for the compound? How long does it last?
You can be happy
|
|
DavidJR
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Quote: Originally posted by Mothman ![](images/xpblue/lastpost.gif) |
Quote: |
Benzhydryl bromide is apparently not all that stable, however.
|
What do you mean by unstable? Are there special storage conditions to meet for the compound? How long does it last? |
Sorry, trying to look for a reference for this but I can't find it. I may be confusing this with another compound, I'm not certain.
|
|
CuReUS
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 928
Registered: 9-9-2014
Member Is Offline
Mood: No Mood
|
|
see this - https://pubs.acs.org/doi/abs/10.1021/cr60170a003
Quote: | Also I don't know if there are other brands, but determining if this brand is suitable should not take too long nor would it be too expensive. If I
have to I'll buy a different brand but this stuff is what I have. | The reason I asked about other brands was
because the tablet form is easier to blend and doesn't create too much crap like the capsules - https://youtu.be/FC_xWQzHW4Q?t=312
|
|
Mothman
Harmless
Posts: 42
Registered: 26-9-2017
Member Is Offline
Mood: Aminated
|
|
Quote: |
Eighty-two per cent sulfuric acid at 25°C. does not attack primary ethers. Secondary ethers can be recovered on immediate dilution, but on standing
conjunct polymerization occurs. Such polymerization occurs immediately with tertiary ethers.
|
Quote: |
Benzhydryl ether does not react with methanol when heated in it. The addition of a few drops of sulfuric acid results in the formation of methyl
benzhydryl ether (13). This resembles the behavior of tertiary ethers with dilute sulfuric acid (204).
|
So what I'm taking out of this paper is that the use of sulfuric acid for this process is likely to be quite inefficient if it works at all. Perhaps I
am misinterpreting these quoted sections however. In the case that I am not, would it be better to use hydrobromic acid instead of sulfuric acid for
this process?
You can be happy
|
|
Jackson
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 189
Registered: 22-5-2018
Location: U S of A
Member Is Offline
Mood: ![:)](./images/smilies/smile.gif) Happy about new glassware
|
|
So would a mixture of NaBr and H2SO4 work, or would I need to use something like HI to do the cleavage?
|
|