Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
New element in the collection: Zr
Hello ScienceMadness,
I recently acquired a couple of zirconium vodka shots from ebay along with the platter for service.
Price was good so of course I have my doubts...
Does anyone has a test in mind (preferably non destructive!) that could be performed to make sure it is indeed Zirconium ?
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
At least you have the density(6.52) and magnet test…
If you have Ar then you can try heating it under Ar with propane torch(Zr mp=1855C), most alloys that can produce that density and cheap enough(add Al
to lower density) should be melted by blowtorch…
[Edited on 181025 by fusso]
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by fusso |
If you have Ar then you can try heating it under Ar with propane torch(
[Edited on 181025 by fusso] |
If you have a torch that will burn in argon...
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
Put sample in Ar, blowtorch outside…
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Outside what?
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
Outside the container
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
non destructive was the idea for the test, anyway i think that the wind from the blowtorch would disperse the argon around the sample, maybe it would
work in a glovebox filled with argon or by flooding the sample in so much argon that it would be a waste
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
ninhydric1
Hazard to Others
Posts: 345
Registered: 21-4-2017
Location: Western US
Member Is Offline
Mood: Bleached
|
|
You got them for a "pretty good price" so you could try a destructive method on one of your samples (unless you really don't want to). But if you do
go along that route eventually, just add some nitric acid to the container, let it dissolve for a short amount of time to leave as little damage as
possible (if desired), then use some sample anions (this website has a good list: http://www.marz-kreations.com/Chemistry/Cation-ID/162u-Zirco... I don't recommend trying the ferro/ferricyanide ones in fear of the production of
HCN) to test. Of course, it is your choice if you want to or not.
The philosophy of one century is the common sense of the next.
|
|
woelen
Super Administrator
Posts: 8031
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Pure Zr is not attacked by nitric acid, so you could use that. If it is attacked, then it is no Zr and then you don't lose anything valuable. If it is
Zr, then nothing happens to your sample.
This of course is not a conclusive test, but it excludes the sample being plain iron, nickel or most of the other cheap first row transition metals.
The magnet test of course also is a good one. It tests for presence of iron and nickel.
[Edited on 26-10-18 by woelen]
|
|
Harristotle
Hazard to Others
Posts: 138
Registered: 30-10-2011
Location: Tinkerville
Member Is Offline
Mood: I tink therefore I am
|
|
One of Zr isotopes is a beta emitter. You can buy zirconium welding rods, if I recall correctly.
Alfoil, paper, old geiger counter and magnet should help.
You should get a signal above background that doesn't much diminish when the a4 copy paper goes in front of it, but does significantly with the
alfoil.
In theory, theory and practice are the same. In practice, however, they may differ. I have not personally conducted the experiment that I have
described, but I remember seing it discussed somewhere.
Cheers,
H.
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
Quote: Originally posted by Harristotle | One of Zr isotopes is a beta emitter. You can buy zirconium welding rods, if I recall correctly.
Alfoil, paper, old geiger counter and magnet should help.
You should get a signal above background that doesn't much diminish when the a4 copy paper goes in front of it, but does significantly with the
alfoil.
In theory, theory and practice are the same. In practice, however, they may differ. I have not personally conducted the experiment that I have
described, but I remember seing it discussed somewhere.
Cheers,
H. |
Zirconium-96 is only 2.8% of the total naturally occurring zirconium, and has a half life of 2x10^19 years, more than the half life of bismuth
(1.9x10^19 years) so I don't think you can detect it with a Geiger counter and AL foil
[Edited on 26-10-2018 by Ubya]
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
Well well !
A lot of good ideas apparently
First, the little plate weights 107,78 grams
The first shot weights 22,93 grams and the second shot weights 25,94 grams
(weighed 3 times then made an average, results were consistent with a cheap scale)
My shots definitely ressemble the one Professor Martyn Poliakoff has in his own Zirconnium video. Imo mine have had a little bit more surface
treatment though. The color of oxides was almost "too much" for me to believe.
https://youtu.be/gNJE2MPktvg
I just tried the HNO3 test with a drop, (that turnout to be a generous drop) of slightly yellowish 90 something % I use for silver.
I left it there for almost a minute but nothing was apparent. Maybe I'll try some mild heat next time.
Oh, no result to magnet test either of course.
I was just thinking about taking out the Oxy-propane torch I bought for my upcoming diamond experiments. Unfortunately I have no Argon.
What's the worst that can happen ? A few colored oxides ?
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
Edit 1: 1 again put 1 drop of conc HNO3 on the back of the plate.
This time I put it on the hotplate at 60° in front of the window.
There was a little bit of white fume when I left. The drop was gone and no apparent damage was detected (eyes and fingertips).
[Edited on 28-10-2018 by Herr Haber]
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
I tried heating the back of the plate with the oxy-torch.
I didnt have to heat very long
The metal wasnt meling oh no... I've got a couple of white sparks from where the metal had been slightly scratched that were totally what I expected !
No additional oxide layer though.
Thank you again for your ideas everyone.
My turn to share I guess:
The vendor's name is Zirconiumforall. He even has a Zr domino set !
|
|
fusso
International Hazard
Posts: 1922
Registered: 23-6-2017
Location: 4 ∥ universes ahead of you
Member Is Offline
|
|
Is zirconium really that cheap/common/popular?
|
|
j_sum1
Administrator
Posts: 6337
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
https://www.ebay.com/itm/EXCLUSIVE-METAL-ZIRCONIUM-Domino-se...
ha! That is very cool. I mean, totally useless and unnecessary but how awesome for an element collection?
|
|
Harristotle
Hazard to Others
Posts: 138
Registered: 30-10-2011
Location: Tinkerville
Member Is Offline
Mood: I tink therefore I am
|
|
Ubya, it depend how much of the "trace" of Zr 93 is present. That has a half life of 1.5 million years, and probably contributes most to the
radioactivity. It is obviously detectable, because it is reported as being present, but probably needs long-ish counting times. It would be
interesting to see how much above background a pure metal sample was!
|
|
Mr. Rogers
Hazard to Others
Posts: 184
Registered: 30-10-2017
Location: Ammonia Avenue
Member Is Offline
Mood: No Mood
|
|
Will Zr really burn in Agron? Zr crucibles are used to smelt Iridium.
[Edited on 29-10-2018 by Mr. Rogers]
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
That I dont know. But I doubt it. But it would have prevented the formation of oxides.
Nothing of that happened with an oxy torch in air. The bottom of the plate was slighly scratched and I have no doubt now the sparks I saw flying were
definitely Zirconium.
Source: https://youtu.be/gNJE2MPktvg
I have suggested the eBay seller to post new items here.
I know some of you coffee lovers will see something they'll like!
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
Mr Rogers, perhaps you are thinking of zirconia , ie. ZrO2?
The melting point of Zr (1855 C) is lower than that of iridium (2466 C).
Also, nothing will burn in argon.
I think the idea suggsted was to heat the Zr in Argon. unionized was probably trying to make the point that it will be practically difficult to heat
Zr in Ar using a torch, because the torch must be in air.
[Edited on 2-11-2018 by phlogiston]
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer
|
|