RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
Rain-X water repellent & properties of glass - is it a coating or just cleaning effect?
Some time ago I had a major fog problem inside my windshield and researched some options and looked at Rain-X and other water repellents for glass and
found that they were mainly solvents or alcohols like Acetone, MEK, methanol, ethanol, Iso-propanol and sometimes water - one product adds a little
HCl and H2SO4.
The Rain-X water repellent wipes were ethanol (30-60%), acetone (10-30%) and isopropanol (10-30%) as per MSDS and the 2-in-1 cleaner/repellent lists
water (60-100%) and acetone (3-7%) as ingredients. Most other products are very similar in their composition.
I had anhydrous acetone, methanol, ethanol & isopropanol and mixed some different combinations and cleaned areas of the windshield and got
different results for each, the individual compounds alone didn't do a whole lot, but together they seemed to work better.
I watched a video about restoring windshields and the guy used 0000 steel wool (the finest) and scrubbed the entire windshield - then applied rain-x.
Looking at how fresh "virgin" glass acts with water, it beads much like rain-x, I'm wondering if these products and procedures are not just cleaning
the surface of contaminates. I can't think how any of the solvents could make a coating on the glass, and I would think the steel wool would just
restore it to the "virgin" surface.
Maybe some of you have had experience with cleaning your glassware that will translate to this process and give insight into it.
The bottom PDF is the one with the acids but it also has a fair amount of Triethoxyoctylsilane which I'm wondering if this acts as a coating (filling
in very small cracks, pours, crevices, etc) or possibly an abrasive.
Anyway, I looked to see if there were other ingredients in the Rain-X original liquid and didn't see anything about "trade secret - not listed" other
than the exact quantites listed, so it seems it is acting as a cleaner. So that might also mean that getting the effect can be had by scrubbing with
steel wool?
Attachment: 630021-630061-Rain-X-Original-Glass-Water-Repellent-Wipes-06212018.pdf (81kB) This file has been downloaded 504 times
Attachment: 630023-Rain-X-Shower-Door-Water-Repellent-06232018.pdf (81kB) This file has been downloaded 753 times
Attachment: Rustoleum NEVERWET Spray - 287337.pdf (132kB) This file has been downloaded 486 times
|
|
Texium
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4552
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
Rain-X does deposit some kind of water-repellent material. I applied some to my windshield recently. If you look at the instructions, you have to
smooth it over the surface of the windshield, and a hazy residue appears as it dries. Once it's fully dried, you take a dry cloth to it and wipe off
the excess residue. It's probably a very small percent of some ethanol soluble non-polar compound that will stick well to glass. Maybe some kind of
silicone? I have also heard that getting it back off of the windshield if you don't want to use Rain-X anymore can be a pain.
|
|
Metacelsus
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2537
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) |
The bottom PDF is the one with the acids but it also has a fair amount of Triethoxyoctylsilane which I'm wondering if this acts as a coating (filling
in very small cracks, pours, crevices, etc) or possibly an abrasive.
|
The silane reagent will chemically bond with the glass, making it hydrophobic (due to the octyl chain).
[Edited on 8-16-2018 by Metacelsus]
|
|
Texium
Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4552
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
Quote: Originally posted by Metacelsus ![](images/xpblue/lastpost.gif) | Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) |
The bottom PDF is the one with the acids but it also has a fair amount of Triethoxyoctylsilane which I'm wondering if this acts as a coating (filling
in very small cracks, pours, crevices, etc) or possibly an abrasive.
|
The silane reagent will chemically bond with the glass, making it hydrophobic (due to the octyl chain).
[Edited on 8-16-2018 by Metacelsus] | Aha, I brushed over that when reading the OP. My random conjecture was
surprisingly close. That would also explain why it's a pain to remove if you no longer want it. You'd probably have to use a strong base...
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
Look at the first two PDF's and you will see that there isn't anything other than solvents in the Rain-X. I looked at about 10 others (rain-x brand)
and they were very similar, one had a propelyene glycol in a small percent, and I think it was a water repellent for fabrics or leather.
The silane, is for the Rustoleum product, which touts "nano" magic in their commercials. This still doesn't explain anything about the rain-x thing
and I looked up the rules for MSDS and SDS and it has to list all ingredients, even if trade secret, but it only has to disclose % and pertinent
medical info for trade secrets. None of that is listed with Rain-X.
|
|
DavidJR
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) | Look at the first two PDF's and you will see that there isn't anything other than solvents in the Rain-X. I looked at about 10 others (rain-x brand)
and they were very similar, one had a propelyene glycol in a small percent, and I think it was a water repellent for fabrics or leather.
The silane, is for the Rustoleum product, which touts "nano" magic in their commercials. This still doesn't explain anything about the rain-x thing
and I looked up the rules for MSDS and SDS and it has to list all ingredients, even if trade secret, but it only has to disclose % and pertinent
medical info for trade secrets. None of that is listed with Rain-X. |
That's not correct, safety data sheets frequently neglect to list ingredients which are not considered to be hazardous at the concentration at which
they are present in the product.
Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) |
Looking at how fresh "virgin" glass acts with water, it beads much like rain-x, I'm wondering if these products and procedures are not just cleaning
the surface of contaminates. I can't think how any of the solvents could make a coating on the glass, and I would think the steel wool would just
restore it to the "virgin" surface.
Maybe some of you have had experience with cleaning your glassware that will translate to this process and give insight into it.
|
Actually, very clean glass is hydrophilic. Water will sheet over it and not bead up at all. This is because the surface of the glass is covered in
silanol groups which are polar.
Try soaking your glassware in a strong base bath overnight and you'll see what I mean.
The long octyl chains on the silane derivative mentioned will of course render the surface non-polar and thus hydrophobic. Similarly stationary phases
for reverse-phase chromatography often consist of silica gel powder which has been treated with a similar silane derivative to produce a surface with
chemically bonded stationary phase molecules- often C18 chains.
[Edited on 16-8-2018 by DavidJR]
|
|
diddi
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 723
Registered: 23-9-2014
Location: Victoria, Australia
Member Is Offline
Mood: Fluorescent
|
|
rain-X is brilliant stuff. i can drive in pelting rain with no windshield wipers on. even at lowish speeds.
Beginning construction of periodic table display
|
|
Deathunter88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 514
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
DavidJR is correct, MSDS's and the newer SDS's only usually list hazardous materials in concentrations above 0.1% (if I remember correctly). You can
easily verify this for yourself by looking at the data sheets for paints and varnishes. Most will only list the solvents in them, but it's obvious
they contain other materials too.
|
|
AJKOER
Radically Dubious
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Deathunter88 ![](images/xpblue/lastpost.gif) | DavidJR is correct, MSDS's and the newer SDS's only usually list hazardous materials in concentrations above 0.1% (if I remember correctly). You can
easily verify this for yourself by looking at the data sheets for paints and varnishes. Most will only list the solvents in them, but it's obvious
they contain other materials too. |
My further understanding based on a thread I did on percarbonate and commercial additivies (like TAED, see comments at http://www.sciencemadness.org/talk/viewthread.php?tid=74533#... ), which in themselves may not be hazardous items, is that the latter are not
mentioned in the contents.
The warning labels, however, suggest toxic issues are possible based on further reactions with water and other items possibly added by the consumer
(like bleach).
A bit confusing unless you have a full understanding of the legal disclosure rules and subsequent aqueous chemistry involved.
My suspicion in the case of the product war between H2O2 vs NaOCl based bleaches, was the need for the benign H2O2 camp to accelerate its power by a
chemical conversion to a nasty organic peroxide which does, in fairness, eventually breakdown into harmless products. However, the persistent
misconception of the safety of their H2O2 based percarbonate product may have led to injuries (and lawsuits) that now obviously requires some very
pronounced changes in warning labels.
Bottom line, read the ingredients and all warning labels to surmise the true nature of the product you are buying!
[Edited on 17-8-2018 by AJKOER]
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2692
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Rain x works by chemically bonding an octyl group to the Silicons in the glass, via
Triethoxyoctylsilane reacts with glass to form EtOH + glass--O-Si-O-Si(OEt)2-Octyl
This effectively leaves a chemically bonded "wax" on the surface of the glass, made of millions of octyl groups on the surface. Only it does not
come off as easily as real wax, which is just a film on the glass, not chemically bonded. But the chemically bonded layer is only essentially one
molecule think at each point, so it eventually comes off as base, fluoride or acid from the air/rain reacts with the glass.
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
After I looked at the various MDSD/SDS's for rain-x products I looked up the international agreement requiring SDS's and what was required to be
listed for the products. It stated that all ingredients must be listed, concentrations/percentages could be given in ranges and if there is a unique
"trade secret" ingredient which is not used by another company (IDK how this is determined) or is not public knowledge of what it is it has to be
listed (as "trade secret or proprietary) and the actual percentage must be given. If the substance is toxic (as per the TSCA) then they must list the
relevant medical information for the secret ingredient in a general way and must be willing to disclose the ingredient to a medical professional in an
emergency.
What I read was pretty clear, I know I have seen a lot of SDS's that seem lacking in their component make-up but that doesn't mean that the SDS is
"legit", meaning official or following the rules of the agreement. It is also very possible that there are many versions of the SDS, one that is
submitted and one that is made much more public, which may omit some data. IDK, it seems one of those things where requirements don't match with what
is happening and that could be some legal loophole or whatnot.
|
|
DavidJR
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Would you be able to link your source for that?
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
These are some of the sites I looked over when I was researching it that are in my browser history. There were a couple others but IDK where they
are.
http://www.ilpi.com/msds/ref/tradesecret.html
http://www.ilpi.com/msds/osha/1910_1200.html#1910.1200
http://www.msds-europe.com/safety-data-sheet-knowledge-base/
https://en.wikipedia.org/wiki/Safety_data_sheet
https://en.wikipedia.org/wiki/Toxic_Substances_Control_Act_o...
|
|
Deathunter88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 514
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) | After I looked at the various MDSD/SDS's for rain-x products I looked up the international agreement requiring SDS's and what was required to be
listed for the products. It stated that all ingredients must be listed, concentrations/percentages could be given in ranges and if there is a unique
"trade secret" ingredient which is not used by another company (IDK how this is determined) or is not public knowledge of what it is it has to be
listed (as "trade secret or proprietary) and the actual percentage must be given. If the substance is toxic (as per the TSCA) then they must list the
relevant medical information for the secret ingredient in a general way and must be willing to disclose the ingredient to a medical professional in an
emergency.
What I read was pretty clear, I know I have seen a lot of SDS's that seem lacking in their component make-up but that doesn't mean that the SDS is
"legit", meaning official or following the rules of the agreement. It is also very possible that there are many versions of the SDS, one that is
submitted and one that is made much more public, which may omit some data. IDK, it seems one of those things where requirements don't match with what
is happening and that could be some legal loophole or whatnot. |
Your research seems to be incorrect or completely outdated. As per the recently adopted GHS system:
DISCLOSURE OF INGREDIENT NAMES
The chemical identity of an ingredient must be disclosed on an SDS in accordance with
Schedule 8 of the WHS Regulations (Disclosure of ingredients). In some cases, a generic
name may be used.
Ingredients that are not classified as hazardous but have an exposure standard and which are present above 1% should be mentioned in the SDS if it is
likely that they might be released under standard storage and application conditions.
Disclosure of ingredient names is not required by the WHS Regulations for those ingredients that meet only physicochemical and/or environmental hazard
classifications, or for nonhazardous
ingredients.
There is no requirement to disclose the identity of ingredients for the following GHS health hazard categories because they fall outside the scope of
the WHS Regulations:
Acute toxicity – Category 5 (oral, dermal and inhalation)
Skin corrosion/irritation – Category 3
Serious eye damage/eye irritation – Category 2B
Aspiration hazard – Category 2
Aquatic toxicity (all categories)
Flammable gas – Category 2
Ozone depletion.
Source: https://www.safeworkaustralia.gov.au/system/files/documents/1705/mcop-preparation-of-safety-data-sheets-for-hazardous-chemicals-v1.pdf
For more information if you still insist otherwise:
https://www.chemsafetypro.com/Topics/GHS/GHS_cut_off_value_GHS_concentration_limit.html
EDIT: Ah yes, any site that still uses MSDS instead of SDS is outdated (as seen in your sources).
[Edited on 18-8-2018 by Deathunter88]
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
IDK what a GHS is but from what I have seen in the US the MSDS is the standard and is often called an SDS.
If you need to find what is in a product, what do you search for? If you need to find what is in "Windex" or some other product, what would you do a
search for?
|
|
wildfyr
Harmless
Posts: 25
Registered: 23-6-2018
Member Is Offline
|
|
Rogue, you can argue about the SDS compliance but the fact remains the Rain-X products work by using alkoxy silanes. I've rotovapped it down and taken
NMR before. Its there. Furthermore its a dead obvious way to do what their product does.
You can (gently) evaporate some down yourself and attempt to examine it. If it was only solvents, then there shouldn't be any residue.
GHS=Globally harmonized system. Its how SDS sheets are being standardized worldwide.
If you need to find out whats in a product you often have to use instruments yourself. Companies don't want to give away their secrets if at all
possible, they spent big bucks having chemists work on those formulations. If any jackass could copy it, they would lose money.
This is a good site for household product ingredients from the US gov't, but it doesn't always have full info
https://hpd.nlm.nih.gov/cgi-bin/household/list?tbl=TblBrands...
you can also search by products containing a certain ingredient.
[Edited on 21-8-2018 by wildfyr]
|
|
DrP
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 625
Registered: 28-9-2005
Member Is Offline
Mood: exothermic
|
|
Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) | IDK what a GHS is but from what I have seen in the US the MSDS is the standard and is often called an SDS.
If you need to find what is in a product, what do you search for? If you need to find what is in "Windex" or some other product, what would you do a
search for? |
We called them MSDS's as the convention for many years. This was changed a few years back by REACH and the EU to simply, SDS to try to standardise
things globally. The GHS is the 'Global Harmonised Standard' I think...
It standardises the hazard labelling used for transport, labelling and SDSs. Much better than 100s of different countries using their own individual
labelling systems - it will avoid confusion in the long run. It is much safer that all of us use the same pictorials and statements for hazard
identification.
Quote: Originally posted by wildfyr ![](images/xpblue/lastpost.gif) | Rain-X products work by using alkoxy silanes. I've rotovapped it down and taken NMR before. Its there.
[Edited on 21-8-2018 by wildfyr] |
Hi Wildfyr! :-) Good to see you here. I guess the silane sets up Si-H bonds on the surface of the glass to repel H2O? Is that how it works? (rather
than being covered in surface hydroxyls which hydrogen bond to the water).
[Edited on 22-8-2018 by DrP]
\"It\'s a man\'s obligation to stick his boneration in a women\'s separation; this sort of penetration will increase the population of the younger
generation\" - Eric Cartman
|
|
wildfyr
Harmless
Posts: 25
Registered: 23-6-2018
Member Is Offline
|
|
Hey P! Ah, I should be more clear. No Si-H bonds involved, rather (RO)XSi-((CH2)XCH3)Y
The active ingredient in Rain-X is either a simple alkyl functionalized alkoxysilane like octyltriethoxysilane, or some oligomeric
polyalklysiloxane-based derivative. Since Rain-X contains some water this distinction is pretty grey, alkoxysilanes will freely oligomerize and
dissociate in a water containing solution. The nature and ratio of alkoxys is that of the alcoholic solvents. Methoxy silanes are most reactive, and
longer chains are less reactive.
In such systems a catalytic amount of acid or base will cause condensation of the alkoxy silloxane with the surface silanols of glass. This is the
reaction https://ars.els-cdn.com/content/image/1-s2.0-S1359835X100008...
In the case of Rain-X the R group is an alkane, which is the source of the hydrophobicity.
[Edited on 22-8-2018 by wildfyr]
|
|
DrP
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 625
Registered: 28-9-2005
Member Is Offline
Mood: exothermic
|
|
Quote: Originally posted by wildfyr ![](images/xpblue/lastpost.gif) | In the case of Rain-X the R group is an alkane, which is the source of the hydrophobicity.
[Edited on 22-8-2018 by wildfyr] |
Ah - that makes sense, thanks - I though it might be a siloxane or something. If R is an alkane then it would repel water for sure.
I did wonder if you would work out where I know you from lol. You did.
\"It\'s a man\'s obligation to stick his boneration in a women\'s separation; this sort of penetration will increase the population of the younger
generation\" - Eric Cartman
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
Quote: Originally posted by wildfyr ![](images/xpblue/lastpost.gif) | Rogue, you can argue about the SDS compliance but the fact remains the Rain-X products work by using alkoxy silanes. I've rotovapped it down and taken
NMR before. Its there. Furthermore its a dead obvious way to do what their product does.
You can (gently) evaporate some down yourself and attempt to examine it. If it was only solvents, then there shouldn't be any residue.
GHS=Globally harmonized system. Its how SDS sheets are being standardized worldwide.
If you need to find out whats in a product you often have to use instruments yourself. Companies don't want to give away their secrets if at all
possible, they spent big bucks having chemists work on those formulations. If any jackass could copy it, they would lose money.
This is a good site for household product ingredients from the US gov't, but it doesn't always have full info
https://hpd.nlm.nih.gov/cgi-bin/household/list?tbl=TblBrands...
you can also search by products containing a certain ingredient.
[Edited on 21-8-2018 by wildfyr] |
I wasn't trying to argue that there wasn't something else in it, I thought there was as well, but from looking at the rules for the MSDS/SDS (current
to the time of the publication of the company provided MSDS - so they should have been compliant with THOSE rules at the time) there should't have
been any other product in the solution besides the solvents - at minimum there should have been a listing of "trade secret" ingredient.
This is kind of frustrating when looking at MSDS even when the ingredients add to 100%, there could be somethign that isn't there, even in large
percentages of 1-15%! I think companies do this because they know no one is going to check each product MSDS but I am assuming that they would be
liable if that unlisted ingredient cause harm in some way, especially if it wasn't even listed as a trade secret and totally omitted!
There is one solvent/glue I was looking at that had Toluene, acetone, MEK and 15% of "trade secret" and listed all the medical precautions for all the
others but nothing for the other ingredient. This stuff smells like super glue but with a much stronger punch (burns nose for hours) and I think it
has to be the secret ingredient Now if something happened b/c the company didn't list the medical issues pertaining to the "trade secret" how can they
be not liable? That is kind of rhetorical, but I'm just showing that there seems to be some seriously harmful stuff that isn't being listed in
products data sheets.
|
|
Deathunter88
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 514
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) | Quote: Originally posted by wildfyr ![](images/xpblue/lastpost.gif) | Rogue, you can argue about the SDS compliance but the fact remains the Rain-X products work by using alkoxy silanes. I've rotovapped it down and taken
NMR before. Its there. Furthermore its a dead obvious way to do what their product does.
You can (gently) evaporate some down yourself and attempt to examine it. If it was only solvents, then there shouldn't be any residue.
GHS=Globally harmonized system. Its how SDS sheets are being standardized worldwide.
If you need to find out whats in a product you often have to use instruments yourself. Companies don't want to give away their secrets if at all
possible, they spent big bucks having chemists work on those formulations. If any jackass could copy it, they would lose money.
This is a good site for household product ingredients from the US gov't, but it doesn't always have full info
https://hpd.nlm.nih.gov/cgi-bin/household/list?tbl=TblBrands...
you can also search by products containing a certain ingredient.
[Edited on 21-8-2018 by wildfyr] |
I wasn't trying to argue that there wasn't something else in it, I thought there was as well, but from looking at the rules for the MSDS/SDS (current
to the time of the publication of the company provided MSDS - so they should have been compliant with THOSE rules at the time) there should't have
been any other product in the solution besides the solvents - at minimum there should have been a listing of "trade secret" ingredient.
This is kind of frustrating when looking at MSDS even when the ingredients add to 100%, there could be somethign that isn't there, even in large
percentages of 1-15%! I think companies do this because they know no one is going to check each product MSDS but I am assuming that they would be
liable if that unlisted ingredient cause harm in some way, especially if it wasn't even listed as a trade secret and totally omitted!
There is one solvent/glue I was looking at that had Toluene, acetone, MEK and 15% of "trade secret" and listed all the medical precautions for all the
others but nothing for the other ingredient. This stuff smells like super glue but with a much stronger punch (burns nose for hours) and I think it
has to be the secret ingredient Now if something happened b/c the company didn't list the medical issues pertaining to the "trade secret" how can they
be not liable? That is kind of rhetorical, but I'm just showing that there seems to be some seriously harmful stuff that isn't being listed in
products data sheets. |
Stop being so paranoid about everything. If anything, it makes no sense for companies to lie in their SDS's as some are no doubt citing it during
legal disputes.
|
|
DrP
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 625
Registered: 28-9-2005
Member Is Offline
Mood: exothermic
|
|
Quote: Originally posted by RogueRose ![](images/xpblue/lastpost.gif) |
I thought there was as well, but from looking at the rules for the MSDS/SDS (current to the time of the publication of the company provided MSDS - so
they should have been compliant with THOSE rules at the time) there should't have been any other product in the solution besides the solvents - at
minimum there should have been a listing of "trade secret" ingredient.
|
They only have to list what is hazardous on the SDS though... you do not need to give a complete ingredients list on a SDS, only a list of those
chemicals that have a hazard classification with their percentages and the associated warnings. So they could well list all of the solvents on the SDS
and not say what the polymer is if it isn't hazardous. Even if it IS hazardous, it still doesn't need to be listed on the SDS if it is under a certain
percentage for its hazard classification.
It's just SDS now. MSDS is old terminology, although I do not know what the convention is in the USA - they are sometimes a century behind when it
comes to global harmonization standards... look at SI units. SI units were globalized last century to avoid confusion and problems for collaborative
work around the globe. There are only 3 countries not using SI units - Burma, Liberia and the USA. We still use pints and miles for shopping and
travel here, but you have to get in line with international standards when collaborating on research and use SI units. A Globally Harmonised System
for hazard labels is a no brainer also.
\"It\'s a man\'s obligation to stick his boneration in a women\'s separation; this sort of penetration will increase the population of the younger
generation\" - Eric Cartman
|
|