drzdude
Harmless
Posts: 35
Registered: 25-2-2018
Member Is Offline
Mood: No Mood
|
|
Separation question
Hey, I found an OTC product with propylene glycol methyl ether, DCM, and nitroethane, and I’m trying so see what would be the best way to separate
the three from each other. DCM can easily be distilled off, but the other two have bp’s very close to one another. Any suggestions for a way to pull
the PGME out of solution possibly? Thanks!
|
|
|
Reboot
Hazard to Others
Posts: 141
Registered: 8-8-2017
Member Is Offline
Mood: No Mood
|
|
The PGME is reportedly miscible with water, while the nitroethane is only slightly soluble. I would probably hit it with some water (which is likely
to cause separation), collect the bottom (organic) layer containing the DCM and nitroethane, then distill it.
|
|
|
DraconicAcid
International Hazard
Posts: 4355
Registered: 1-2-2013
Location: The tiniest college campus ever....
Member Is Offline
Mood: Semi-victorious.
|
|
Quote: Originally posted by Reboot  | | The PGME is reportedly miscible with water, while the nitroethane is only slightly soluble. I would probably hit it with some water (which is likely
to cause separation), collect the bottom (organic) layer containing the DCM and nitroethane, then distill it. |
I was going to suggest something along these lines after looking up the solubility of the two. Rather than just "hitting it", you'd probably want to
do several extractions with water to get the majority of the PGME out.
Please remember: "Filtrate" is not a verb.
Write up your lab reports the way your instructor wants them, not the way your ex-instructor wants them.
|
|
|
drzdude
Harmless
Posts: 35
Registered: 25-2-2018
Member Is Offline
Mood: No Mood
|
|
Yeah I saw on wiki it’s miscibility in water, and figured that would be the best bet. But never worked with PGME before so figured I’d check.
Thanks!
| Quote: Originally posted by Reboot | | The PGME is reportedly miscible with water, while the nitroethane is only slightly soluble. I would probably hit it with some water (which is likely
to cause separation), collect the bottom (organic) layer containing the DCM and nitroethane, then distill it. |
|
|
|
Reboot
Hazard to Others
Posts: 141
Registered: 8-8-2017
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by DraconicAcid | | Rather than just "hitting it", you'd probably want to do several extractions with water to get the majority of the PGME out. |
Indeed. :-) I should be more explicit. Since nitroethane is slightly soluble in water (and may only be present in moderate amounts in the feed
stock) water volumes should be kept minimal. Add enough to cause separation, then wash perhaps twice with small additional amounts of water (less
water than organic layer.)
Although it depends on your ultimate goal. If purity is more important than recovery, larger wash volumes/more washes could be appropriate.
|
|
|
Vosoryx
Hazard to Others
Posts: 282
Registered: 18-6-2017
Location: British Columbia, Canada
Member Is Offline
Mood: Serial Apple Enjoyer
|
|
What product is this, if you don't mind me asking?
"Open your mind son, before someone opens it for you." - Dr. Walter Bishop
|
|
|
happyfooddance
National Hazard
Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline
Mood: No Mood
|
|
Nitroethane behaves strangely with water, especially in the presence of other solvents, IME. Look at this datasheet and tell me if you can see what I
mean.
https://www.google.com/url?sa=t&source=web&rct=j&...
If I were you, I would formulate as many extraction routes as I could think of, and try them out on a small scale.
I think the statement that nitroethane is only slightly soluble in water should only be taken at face value if you have a centrifuge. Otherwise, it
may be safe to say it can form tenacious emulsions with aqueous solutions. If you are doing water extractions, perhaps try adding different amounts of
different salts. CaCl2 is one I'd try.
Mostly I am assuming that you are wanting the nitroethane in pure form, since those other two components are much more easily accessible.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
