Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
Making an induction heater for fastener removal?
I have a small problem, a drain plug frozen into an Iron gear box. Mechanic tasked with changing gear lube totally stripped the hex drive indentation
trying to remove (with an impact wrench!). He then refused to work on it further, and suggested whole gear box be replaced (for an estimated several
THOUSAND dollars, if a part could be located. Thanks, buddy!).
I suspect it may also have been cross threaded on installation by a previous mechanic, who then forced it home anyhow.
I need to get it out. Without breaking the gear box, which is not AFAIK available as a new part, and if it were, would cost more than the repair would
be worth to obtain and install.
These tools are useful for spot heating a bolt in places a torch would be inadvisable or too imprecise-
![shopping.jpg - 54kB](http://www.sciencemadness.org/talk/files.php?pid=499291&aid=63018)
[Edited on 3-12-2017 by Bert]
![maxresdefault.jpg - 96kB](http://www.sciencemadness.org/talk/files.php?pid=499291&aid=63020)
But the cheapest version is still kind of expensive. Looking at eBay, Amazon, etc., the components are available and inexpensive...
And after the fastener removal project, the same components could make a small crucible heater for other projects.
Looking at the many online offers of induction heaters as assembled boards without enclosures and associated heating coils. Anyone here done a similar
project? (I have seen several posts by members about making and using small induction heaters for smelting).
[Edited on 3-12-2017 by Bert]
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
gnitseretni
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 282
Registered: 5-1-2007
Location: Colombia
Member Is Offline
Mood: No Mood
|
|
If possible, weld a short bolt to the drain plug so you can put a wrench on the bolt. That's what I'd try anyway.
|
|
aga
Forum Drunkard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
Surely it's not the bolt you want to heat, but the casing ?
A blowtorch would be the best bet, even though there is Oil in there.
Protect everything else with plumber's mats (or pyrolysed bread ) and go slow to
get as even a heat as possible.
Angle-grind the head on two sides so you can at least use a normal wrench on it.
If it is cross threaded, consider the painful option of drilling it out and re-tapping the hole a size bigger, and a new plug.
Probably less painful than a few $1000 tho.
|
|
unionised
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5109
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Can you drill and tap a new hole next to the original?
|
|
aga
Forum Drunkard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
If there is enough 'meat' in the part, that would be an excellent idea.
Now that is a good example of thinking sideways
|
|
RogueRose
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1590
Registered: 16-6-2014
Member Is Offline
|
|
There are screw extraction thread taps which tap a hole in a counter clockwise manner. Drill the hole, tap it, insert a bolt ("left hand threaded")
and turn it counter clockwise and it should turn the plug
here is are some taps that can be used
http://www.ebay.com/bhp/left-hand-tap
If the plug isn't recessed, what about just grinding 2 parallel sides flat and using an adjustable wrench to remove it.
|
|
Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
Plug is flush to slightly recessed. Intent is to heat the metal AROUND the hole. Chill the plug, probably with a CO2 tank. When loosened by
expanding the hole and shrinking the plug thermally, unscrew.
Question of wether the gear box can be cracked or permanently distorted to uselessness by heating unevenly? Unknown.
Drilling a new plug hole is actually something worth looking at, thanks-
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
aga
Forum Drunkard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7030
Registered: 25-3-2014
Member Is Offline
|
|
A coil induction heater will heat the bit inside the coil, which is why i thought you wanted to heat the bolt.
unionised's idea does sound like the best so far.
If it were me, i;d want the original bolt out and fixed, OCD style.
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1309
Registered: 26-7-2004
Location: Middle Earth
Member Is Online
Mood: A trace of hope...
|
|
Screw extractors tend to be made of hardened steel , and are therefore brittle. If an impact wrench wouldn't shift it, then I'd say a screw extractor
will snap before achieving anything.
I'd probably go for a gas torch or hot air gun, before trying something exotic like induction heating. The best chiller would be a can of 'freeze
spray', which is usually an HFC and chills to -50C. Easily directed onto a small spot.
Last ditch effort: drill it out, with a left-hand spiral drill bit (yes they do exist) - that way if it loosens during drilling it will unscrew.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
NedsHead
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 9-12-2014
Location: South Australia
Member Is Offline
Mood: No Mood
|
|
I use my arc welder with two carbon electrodes to heat up and remove seized bolts, I stick one electrode in the hand piece and one in the ground
clamp, they actually make a special hand piece for arc welders to do this but it's just as easy to work with both hands.
|
|
Vosoryx
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 282
Registered: 18-6-2017
Location: British Columbia, Canada
Member Is Offline
Mood: Serial Apple Enjoyer
|
|
If I were in your situation, I would grind angles into the head so you can grip it with a pair of vice grips, and heat up the surrounding area with a
torch. Get a friend to lean on the handle of the vice grips.
Alternatively, if you need more torque than can be offered by a pair of vice grips, weld a chunk of re-bar or angle iron to it. Sit on that. (If it's
in an accessible position)
If all else fails, drill it out and re-tap. Though left handed bits do exist, they're pretty expensive.
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
I feel your pain, Bert. With the information you've provided, I don't think you'll be able to acheive what you want with an induction heater.
My advice is to drill it out. You can try a bolt extractor (I've used these before http://www.lasertools.co.uk/product/0295 - you'll need a tap wrench for effective use) but if you suspect it's been cross threaded by a previous
mechanic the best option is to drill it out and either re-tap it or use a helicoil kit (I've used this kit several times and its a life saver in the
garage: https://www.amazon.co.uk/BERGEN-Professional-Quality-Helicoi...).
Sounds like it's going to be a messy job (assuming its still filled with oil - that'll leak when you drill through) but for the sake of saving a grand
its probably worth it.
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3631
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I second the helicoil last resort option - a great invention.
CAUTION : Hobby Chemist, not Professional or even Amateur
|
|
Bert
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2821
Registered: 12-3-2004
Member Is Offline
Mood: " I think we are all going to die. I think that love is an illusion. We are flawed, my darling".
|
|
Yeah, I just wanted to buy/build a new toy.
Doing it mechanically, drilling and then using an extractor is sensible.
Also using heat cycling and Kroil repeatedly before even trying to unscrew or drill and extract would be wise. I know the mechanic didn't.
[Edited on 4-12-2017 by Bert]
Rapopart’s Rules for critical commentary:
1. Attempt to re-express your target’s position so clearly, vividly and fairly that your target says: “Thanks, I wish I’d thought of putting it
that way.”
2. List any points of agreement (especially if they are not matters of general or widespread agreement).
3. Mention anything you have learned from your target.
4. Only then are you permitted to say so much as a word of rebuttal or criticism.
Anatol Rapoport was a Russian-born American mathematical psychologist (1911-2007).
|
|
zed
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Hex Drive indentation?
Are you suggesting this is an Allen Head, type plug... That has had the sides of the hex hole stripped out?
Drill, if you must. Then, get a Square Extractor of the correct size, and back your plug out. If it doesn't work, you must drill out the whole plug,
and tap a new (slightly larger)hole. Don't break off an extractor inside the plug!
The hardened steel of an extractor, is quite difficult to drill through.
Square extractors are less likely to break than reverse thread extractors. Stronger.
Consult a bicycle shop/bicycle machinist. Such an individual might actually be somewhat altruistic.
Last time I faced an unsolvable problem, and needed a custom made part to proceed... A friendly local bike shop made that part for a whomping $15
dollars.
[Edited on 5-12-2017 by zed]
[Edited on 5-12-2017 by zed]
[Edited on 5-12-2017 by zed]
[Edited on 5-12-2017 by zed]
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1309
Registered: 26-7-2004
Location: Middle Earth
Member Is Online
Mood: A trace of hope...
|
|
If you are still keen on making an induction heater then http://4hv.org is the place to go for advice.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
NedsHead
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 409
Registered: 9-12-2014
Location: South Australia
Member Is Offline
Mood: No Mood
|
|
After the heat cycling and penetrating oil try and undo the sump plug using a small cold chisel or centre punch, I've been able to remove a few bolts
sheared off flush by carefully undoing them with a chisel and/or punch, the shock helps get them turning
|
|
Corrosive Joeseph
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 915
Registered: 17-5-2015
Location: The Other Place
Member Is Offline
Mood: Cyclic
|
|
Quote: Originally posted by NedsHead ![](images/xpblue/lastpost.gif) | After the heat cycling and penetrating oil try and undo the sump plug using a small cold chisel or centre punch, I've been able to remove a few bolts
sheared off flush by carefully undoing them with a chisel and/or punch, the shock helps get them turning |
This has never failed for me and I torture myself with this shit regularly.
If you can drill a small, moderately deep hole in your plug that will stop a punch from slipping, it will take an almighty beating.
Gas flame if you have to. Squirts of penetrating fluid on the cool down.
Repeat.......
If the gearbox is actually coming out anyways, it will be even easier to do it on the floor, plenty of space to get at it and no restrictions on
swinging away on the punch........
/CJ
[EDIT] - Damn Typo
[Edited on 5-12-2017 by Corrosive Joeseph]
Being well adjusted to a sick society is no measure of one's mental health
|
|
Cezium
Harmless
Posts: 39
Registered: 5-1-2015
Member Is Offline
Mood: No Mood
|
|
I have bought this https://ebay.com/itm/1000W-50A-ZVS-Induction-Heating-Machine... and it works fine for me.
|
|