| Pages:
1
..
54
55
56
57
58
..
81 |
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
Quote: Originally posted by Bert  | There is considerable information available for high explosives based on mixtures of Potassium chlorate and nitrobenzene or of ammonium nitrate and
nitromethane.
Do any know of data on mixtures of Potassium chlorate and nitromethane? VOD, impact and friction sensitivity? (high, one assumes...) STABILITY? Was
there ever any industrial use made of this mixture?
A quick Google search shows some amateur experimental uses, and at least one video. |
The main problems with nitromethane (NM) are:
1°) It is near perfect OB
CH3-NO2 --> CO2 + 3/2 H2
3/2 H2 + 3/4 O2 --> 3/2 H2O
OB = -19,6%
This means that for perfect OB one needs 50% KClO3 and 50% NM (halve a mole of KClO3 to get 3/2 O vs 1 mole of NM thus 61g and 61g)
This will cause fast sedimentation of the KClO3...unless some active thickener gellig agent is used ==> Nitrocellulose is a good gelling agent.
Into ANNM and ANFO the % of liquid vs solid is low thus it can be held by capilarity forces into place without too much segregation.
2°) It is of low density... Nitrobenzene (NB) is slightly higher in density and DNB or DNT oils are much denser thus increasing VOD and detonic
parameters of the oxydiser/fuel mix
3°) NB contains a lot more fuel (C and H atoms/bad OB) to burn so the heat of combustion per kg is much higher than NM...also one will need more
solid vs the liquid to acheive a perfect OB mix and one will be closer to conventional ANNM/ANFO mixes with regards to solid/liquid ratio.
4°) NB has a higher viscosity, a lower inflamability and lower volatility than NM; viscosity will help in holding the mix stabler with regard to
sedimentartion segregation; the other parameters will help for storage safety...
*************************************************
The problem with KClO3 is its dead weight counterpart... solid KCl into the detonations products...
NH4NO3 has the advantage to increase the overal gas generated during detonation process and thus the explosion mechanical work or blast pressure.
So better oxydisers would be (eventually with help of active/or energy rich fuel gelling agents stables vs the oxydisers):
A) Ammonium perchlorate ==> AP/NM
AP has a low VOD but a very high density; the low VOD is caused by its overoxygenation...adding NM will reveal its maximum power...
B) Hydrazinium nitrate ==> HN/NM
C) Hydrazinium pechlorate ==> HP/NM
D) Hydroxylamine nitrate ==> HAN/NM
E) Hydroxylamine perchlorate ==> HAP/NM
F) Urea perchlorate ==> UP/NM
G) Other oxydisers based on nitroform or dinitramide
==> HNF/NM (hydrazinium nitroformate (stable?)-NM)
==> ANF/NM (Ammonium nitroformate-NM)
==> HANF/NM (hydroxylaminium nitroformate (stable?)-NM)
==> UNF/NM (urea nitroformate (stable?)-NM)
==> HDN/NM (hydrazinium dinitramide (stable?)-NM)
==> ADN/NM (Ammonium dinitramide-NM)
==> HADN/NM (hydroxylaminium dinitramide (stable?)-NM)
==> UDN/NM (urea dinitramide (stable?)-NM)
******************************************
Sensitivity to impact or friction of KClO3/NM mix should be driven by the weakest explosive link... what is NM... thus not exceptionnal except if some
conventionnal basic media is present to help.
Storage stability should be of no concern if KClO3 and NM are pure enough...and exempt of water...
KClO3 is uncompatible with acidic compounds... and NM is moderately acidic and only express its weak acidity if water is present... and KClO3 is not
hygroscopic at all...it crystallizes/precipitates without water of hydration...
********************************
The use of higher homologues of NM like 1,2-dinitroethane (DNE) or 1,2,3-trinitropropane (TNPr) will bring more density to the mixes and allow those
to reach regios of VOD (between 8,0-10 km/s) and very high brisance...
[Edited on 6-9-2017 by PHILOU Zrealone]
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
UkAmateur
Harmless
Posts: 11
Registered: 4-8-2017
Member Is Offline
Mood: No Mood
|
|
EM Short Question
I hope these questions aren't regarded as overly kewlish and whilst they have probably been answered previously I have utse and read numerous posts
with out a definitive answer being apparent.
But given this is the short question/quick answer thread I thought I may as well ask.
1, How much A.P. (acetone peroxide) is required to successfully initiate detonation of E.T.N (ethryitol tetranitrate)?
The ETN will be sensitized by addition of 15%(b.w) of aluminum powder. Containment will be a thin walled aluminum tube approx 6mm diameter.
2, How much ETN is required to successfully initiate detonation of nitrocellulose?
(Trinitrate, properly washed, neutralised, stabilized, dried and pressed to optimal density) containment varied.
I apologise in advance if these questions aren't suited to this thread and am happy for a moderator to delete or move to the appropriate thread or
subsection if deemed necessary.
Many thanks in advance.
E2a I realise AP is less than an ideal primary and I loath to synth it again (been several years since I last did on account of a Darwin award worthy
mistake on by behalf which very nearly lost me two fingers) but unless my UTC source of sodium azide comes through soon my options are limited to
AP/HMTD. Its worth saying that both questions are at this point hypothetical. As I am still unconvinced that AP is worth the risk. Its amazing how
convincing our little accidents can be eh..
Anyways just wanted to clarify as I'm not some 14yr old kid and have the appropriate respect for the compounds in question.
Again, many thanks
[Edited on 13-9-2017 by UkAmateur]
[Edited on 13-9-2017 by UkAmateur]
|
|
|
gdflp
|
Threads Merged
13-9-2017 at 17:21 |
James Ikanov
Hazard to Self
Posts: 81
Registered: 12-7-2015
Location: Alaska
Member Is Offline
Mood: Zen
|
|
I'm not often the sort to suggest this kind of thing, but if you can find an older car (I think pre-2004? google might be more informative) with
intact original airbags, those systems primarily used sodium azide. You can gut them and strip them for sodium azide if you use the right tools and
are very gentle about removing the gas generator.
I should clarify I've never personally attempted this method of procurement. But I read about it in a text written by someone I would qualify well as
an expert in the field.
Either way, I'd say making Nickel Hydrazine Nitrate or a nitroguanidine derivative would both be highly preferable to AP. If neither could be
produced, perhaps you could consider the MnO2 thermite initiator produced by another member of this forum?
“To do good work one must eat well, be well housed, have one's fling from time to time, smoke one's pipe, and drink one's coffee in peace” -
Vincent Van Gogh
|
|
|
j_sum1
Administrator
Posts: 6333
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
IIRC, Panache is our resident expert on airbag systems. And again, IIRC he does not recommend disassembly to recover NaN3.
|
|
|
Corrosive Joeseph
National Hazard
Posts: 915
Registered: 17-5-2015
Location: The Other Place
Member Is Offline
Mood: Cyclic
|
|
I once spent a night reading about obtaining sodium azide from airbags and came to the conclusion it was just too dangerous.
/CJ
|
|
|
NeonPulse
Hazard to Others
Posts: 417
Registered: 29-6-2013
Location: The other end of the internet.
Member Is Offline
Mood: Isolated from Reality! For Real this time....
|
|
I do this on video for my YT channel. The biggest bastard is separation of the KNO3 from the NaN3 which I have not succeeded in doing yet- not that I
have really attempted to though. I dismantled two different airbags from two different car makers and there is a marked difference in construction of
each unit but the idea is the same.
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by UkAmateur | I hope these questions aren't regarded as overly kewlish and whilst they have probably been answered previously I have utse and read numerous posts
with out a definitive answer being apparent.
But given this is the short question/quick answer thread I thought I may as well ask.
1, How much A.P. (acetone peroxide) is required to successfully initiate detonation of E.T.N (ethryitol tetranitrate)?
The ETN will be sensitized by addition of 15%(b.w) of aluminum powder. Containment will be a thin walled aluminum tube approx 6mm diameter.
2, How much ETN is required to successfully initiate detonation of nitrocellulose?
(Trinitrate, properly washed, neutralised, stabilized, dried and pressed to optimal density) containment varied.
I apologise in advance if these questions aren't suited to this thread and am happy for a moderator to delete or move to the appropriate thread or
subsection if deemed necessary.
Many thanks in advance.
E2a I realise AP is less than an ideal primary and I loath to synth it again (been several years since I last did on account of a Darwin award worthy
mistake on by behalf which very nearly lost me two fingers) but unless my UTC source of sodium azide comes through soon my options are limited to
AP/HMTD. Its worth saying that both questions are at this point hypothetical. As I am still unconvinced that AP is worth the risk. Its amazing how
convincing our little accidents can be eh..
Anyways just wanted to clarify as I'm not some 14yr old kid and have the appropriate respect for the compounds in question.
Again, many thanks
[Edited on 13-9-2017 by UkAmateur]
[Edited on 13-9-2017 by UkAmateur] |
Above the critical mass of detonation of the explosive into that diameter under the given density... but like many explosive material... it is not
reliable D2D explosive...
==> This is the case of ETN / CTAP (cyclo-tri-aceton-peroxide)... depends on too many factors...
==> Trial error and better too much than too little... but that is not nice with regards to the inherent danger of CTAP...
It is said that ETN may be thermaly pushed to D2D with help of Aluminium under heating... so maybe a mild heating mix may do the trick (or a stronger
one like exploding CuO/Al thermite.
Again ETN is not easy to D2D reliably especially in tiny amounts...
Better shift to SADS/SANC (Silver acecytlide double salt/ Silver acetylide nitrato complex)... pretty OTC and very easy to detonate even from minute
amounts (without confinement what CTAP or ETN hardly do in so tiny amounts) by flame or heat > 180 °C.
==> When using KMnO4/glycerine... it detonates before the mix has the time to burst into flame...
[Edited on 14-9-2017 by PHILOU Zrealone]
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
UkAmateur
Harmless
Posts: 11
Registered: 4-8-2017
Member Is Offline
Mood: No Mood
|
|
Thanks for the replies guys. I think I'm gonna shelve the AP idea for now. Even in minute amounts its just to dangerous (to handle/manipulate, the
synthesis itself is easy and measures can be taken to reduce risks but when it comes to handling the dry product.. Well I don't need to elaborate)
I'll concentrate on acquiring the required reagents for other primaries first. And maybe look into docs method of detonating ETN caps too at the same
time..
I've got plenty of chlorates available (and my cell can easily produce perchlorate too) so the perchlorate primaries are perhaps another option as
well.
I was hoping to acquire sodium azide via the car airbag route as I have a friend in the car breaking business but reading a couple of the above posts
it may not be as simple as I first hoped..
As is often the case, less speed = more haste.
This isn't the kind of hobby where rushing things brings you any medals. In fact, often the opposite.
I'll keep reading.
Again, many thanks.
|
|
|
Rosco Bodine
Banned
Posts: 6370
Registered: 29-9-2004
Member Is Offline
Mood: analytical
|
|
For sluggish, low efficiency / low impulse / slow DDT / slow self accelleration initiators there is a very real constraint of critical diameter that
works against a practical design at below about 3/8" inch diameter for the initiator column. TCAP is only very marginally usable as an initiator even
at that 3/8" diameter in an amount of several grams topped off with a first fire "kicker" of AP / bullseye putty as a low press loading "hand pressed"
firing train. HMTD performs a little better, and DDNP still better. At a 1/4" inch column diameter, from my tests, which were not done on ETN or other
sensitive base charge, none of the sluggish initiators will perform like they should. Reported by others NHN and other sluggish initiators are going
to also require the larger diameter charge columns to be useful loadings.
As for the perchlorates, triaminoguanidine perchlorate over guanidine perchlorate could be an interesting combination of initiator and base charge.
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by UkAmateur | Thanks for the replies guys. I think I'm gonna shelve the AP idea for now. Even in minute amounts its just to dangerous (to handle/manipulate, the
synthesis itself is easy and measures can be taken to reduce risks but when it comes to handling the dry product.. Well I don't need to elaborate)
I'll concentrate on acquiring the required reagents for other primaries first. And maybe look into docs method of detonating ETN caps too at the same
time..
I've got plenty of chlorates available (and my cell can easily produce perchlorate too) so the perchlorate primaries are perhaps another option as
well.
I was hoping to acquire sodium azide via the car airbag route as I have a friend in the car breaking business but reading a couple of the above posts
it may not be as simple as I first hoped..
As is often the case, less speed = more haste.
This isn't the kind of hobby where rushing things brings you any medals. In fact, often the opposite.
I'll keep reading.
Again, many thanks. |
Why not make hydrazine hydrogeno sulfate the conventionnal way (ammonia or urea and NaOCl (bleach)) and convert it to NaN3... plenty of receipe and
info here into the forum or elsewhere on YouTube...
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by Rosco Bodine | For sluggish, low efficiency / low impulse / slow DDT / slow self accelleration initiators there is a very real constraint of critical diameter that
works against a practical design at below about 3/8" inch diameter for the initiator column. TCAP is only very marginally usable as an initiator even
at that 3/8" diameter in an amount of several grams topped off with a first fire "kicker" of AP / bullseye putty as a low press loading "hand pressed"
firing train. HMTD performs a little better, and DDNP still better. At a 1/4" inch column diameter, from my tests, which were not done on ETN or other
sensitive base charge, none of the sluggish initiators will perform like they should. Reported by others NHN and other sluggish initiators are going
to also require the larger diameter charge columns to be useful loadings.
As for the perchlorates, triaminoguanidine perchlorate over guanidine perchlorate could be an interesting combination of initiator and base charge.
|
Nice data/infos Rosco  
The NiHN (Nickel nitrate hydrazino complex) is indeed too much on the edge between a primary/Secondary... that's why I developped the synergetical mix
with SADS/SANC (1/1 to 2/1)... so:
1°) initiability of of the mix is strongly improved vs NiHN alone
==> reducing the needed amount and critical diameter of detonation allowing for a lower diameter detonator and shorter one (development distance of
the D2D much shorter)
2°) overal power of the mix is improved vs SADS alone since NiHN is more brisant and display a higher VOD.
Hence the synergy 
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
gdflp
|
Thread Split
17-9-2017 at 17:10 |
joseph6355
Hazard to Others
Posts: 144
Registered: 23-8-2017
Member Is Offline
Mood: Nitrated
|
|
I need a primary explosive that won't kill me easily, is chemically stable, can be synthesized at a home lab and is not TOO expensive to make.
HMTD is cool, but it is not chemically stable.
I need an explosive to make a blasting cap for my Dunnite.
Lead azide is not an option for me. It is very time demanding and expensive to make.
|
|
|
kratomiter
Hazard to Others
Posts: 106
Registered: 30-9-2012
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by joseph6355 | I need a primary explosive that won't kill me easily, is chemically stable, can be synthesized at a home lab and is not TOO expensive to make.
HMTD is cool, but it is not chemically stable.
I need an explosive to make a blasting cap for my Dunnite.
Lead azide is not an option for me. It is very time demanding and expensive to make. |
SADS, without any doubt.
|
|
|
kratomiter
Hazard to Others
Posts: 106
Registered: 30-9-2012
Member Is Offline
Mood: No Mood
|
|
I tried to sensitize nitromethane with a 5% epoxy curing agent based on polyamine. The PLX-like explosive is green, I put 6 grams inside a syringe I
tried to detonate it with SADS/MHN (500 mg) without success. Should I add a booster or switch to another amine? EDA is hard to get.
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by kratomiter | | I tried to sensitize nitromethane with a 5% epoxy curing agent based on polyamine. The PLX-like explosive is green, I put 6 grams inside a syringe I
tried to detonate it with SADS/MHN (500 mg) without success. Should I add a booster or switch to another amine? EDA is hard to get.
|
What polyamine?
Maybe the amine group into your product is not basic enough to force the nitromethane to its nitronate form...
==> The nitronate form is responsible of the sensitivity.
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
joseph6355
Hazard to Others
Posts: 144
Registered: 23-8-2017
Member Is Offline
Mood: Nitrated
|
|
| Quote: Originally posted by kratomiter | | Quote: Originally posted by joseph6355 | I need a primary explosive that won't kill me easily, is chemically stable, can be synthesized at a home lab and is not TOO expensive to make.
HMTD is cool, but it is not chemically stable.
I need an explosive to make a blasting cap for my Dunnite.
Lead azide is not an option for me. It is very time demanding and expensive to make. |
SADS, without any doubt. |
Hi! Thanks for answering.
By SADS you mean silver acetylide?
Doesn't seems hard to make. I can buy silver nitrate locally and recrystallize it, and then generate some acetylene gas.
How stable is it? Will it decompose or change its chemical structure in contact with metals, light, time?
I'd like to know more about it.
How much SADS would be required to detonate, lets say, 300g of dunnite?
|
|
|
kratomiter
Hazard to Others
Posts: 106
Registered: 30-9-2012
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by PHILOU Zrealone | | Quote: Originally posted by kratomiter | | I tried to sensitize nitromethane with a 5% epoxy curing agent based on polyamine. The PLX-like explosive is green, I put 6 grams inside a syringe I
tried to detonate it with SADS/MHN (500 mg) without success. Should I add a booster or switch to another amine? EDA is hard to get.
|
What polyamine?
Maybe the amine group into your product is not basic enough to force the nitromethane to its nitronate form...
==> The nitronate form is responsible of the sensitivity. |
Sorry, it wasn't a polyamine, it was a polyetheramine, so maybe is not basic enough. Next amine to try is hexamine.
|
|
|
kratomiter
Hazard to Others
Posts: 106
Registered: 30-9-2012
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by joseph6355 | | Quote: Originally posted by kratomiter | | Quote: Originally posted by joseph6355 | I need a primary explosive that won't kill me easily, is chemically stable, can be synthesized at a home lab and is not TOO expensive to make.
HMTD is cool, but it is not chemically stable.
I need an explosive to make a blasting cap for my Dunnite.
Lead azide is not an option for me. It is very time demanding and expensive to make. |
SADS, without any doubt. |
Hi! Thanks for answering.
By SADS you mean silver acetylide?
Doesn't seems hard to make. I can buy silver nitrate locally and recrystallize it, and then generate some acetylene gas.
How stable is it? Will it decompose or change its chemical structure in contact with metals, light, time?
I'd like to know more about it.
How much SADS would be required to detonate, lets say, 300g of dunnite? |
My SADS is stable enough stored under ethanol in a dark place. I think dunnite is quiet insensitive, maybe you need a booster to detonate it, like
picric acid.
|
|
|
joseph6355
Hazard to Others
Posts: 144
Registered: 23-8-2017
Member Is Offline
Mood: Nitrated
|
|
| Quote: Originally posted by kratomiter |
My SADS is stable enough stored under ethanol in a dark place. I think dunnite is quiet insensitive, maybe you need a booster to detonate it, like
picric acid. |
Nice.
Since you mentioned solubility, how soluble is SADS in ethanol, acetone and other solvents? The wikipedia article states that it is insoluble in
water.
If it is insoluble in ethanol, it is indeed a good choice of chemical, since it would dry the SADS much faster than water.
How much SADS can I store safely together, in the same container?
Thanks! 
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by kratomiter | | Quote: Originally posted by PHILOU Zrealone | | Quote: Originally posted by kratomiter | | I tried to sensitize nitromethane with a 5% epoxy curing agent based on polyamine. The PLX-like explosive is green, I put 6 grams inside a syringe I
tried to detonate it with SADS/MHN (500 mg) without success. Should I add a booster or switch to another amine? EDA is hard to get.
|
What polyamine?
Maybe the amine group into your product is not basic enough to force the nitromethane to its nitronate form...
==> The nitronate form is responsible of the sensitivity. |
Sorry, it wasn't a polyamine, it was a polyetheramine, so maybe is not basic enough. Next amine to try is hexamine. |
Polyetheramine are in principle basic enough, but everything depends onto the molecular structure of it some have very large carbonaceous counterpart
vs the amine moiety; hence the amount of product to acheive same sensitizing effect as ammonia or ethylene diamine will be much higher than 5% by
weight can be 10, 15, 20% or even more for very high MW polyetheramine with little amino groups unit per molecule...
Hexamine is not basic enough... you can eat it...
It was used as ancient cure for urinal infections hence the name of urotropine... this effect is obtained by the slow hydrolysis of the
hexamethylenetetramine and slow release of formaldehyde (bactericide but also carcinogen) and of basic counterpart.
Hydrolysis only occure into waterous media...
You will have more chance to allow some NM (nitromethane) to react with formaldehyde to get dinitropropane, nitroethanol, nitroethene,
2-nitropropandiol or nitroisobutyltetrol...then reduce this by SnCl2/HCl to get the amines from it and to allow this to mix after isolation with NM...
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by joseph6355 | | Quote: Originally posted by kratomiter |
My SADS is stable enough stored under ethanol in a dark place. I think dunnite is quiet insensitive, maybe you need a booster to detonate it, like
picric acid. |
Nice.
Since you mentioned solubility, how soluble is SADS in ethanol, acetone and other solvents? The wikipedia article states that it is insoluble in
water.
If it is insoluble in ethanol, it is indeed a good choice of chemical, since it would dry the SADS much faster than water.
How much SADS can I store safely together, in the same container?
Thanks! |
SADS is pretty much insoluble in any solvent except very basic or acidic ones...
SADS is silver acetylide double salt or SANC silver acetylide nitrato complex... it is related to silver acetylide but it is not the same.
SA = Ag2C2
SANC/SADS = Ag2C2.xAgNO3 or Ag2C2.xAgNO3.yHNO3
The fact SANC/SADS contains nitrate into its complex structure allows form more energetic output and power... since the oxygen will help burning part
of the acetylen carbonaceous fuel... but not all as proven by the fact that the addition of KClO3 increases the power up to 40% by weight vs plain
SADS/SANC ==> so not enough oxydizer present for perfect OB (oxygen balance)
There are plenty of info about it all over the energetic section ==> Use the search engine
==> The safe amount to handle depends onto the operator, his ability to make the product pure following good procedures and onto the container.
I have had more than 15 grams stored at the same place under a granulated form with finer powder parts for long time.
Avoid light exposure for too long especially strong halogen ones and UV (like from the sun)... avoid too much friction, shock and heat... 150°C can
set it off.
[Edited on 3-10-2017 by PHILOU Zrealone]
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
joseph6355
Hazard to Others
Posts: 144
Registered: 23-8-2017
Member Is Offline
Mood: Nitrated
|
|
| Quote: Originally posted by PHILOU Zrealone | | Quote: Originally posted by joseph6355 | | Quote: Originally posted by kratomiter |
My SADS is stable enough stored under ethanol in a dark place. I think dunnite is quiet insensitive, maybe you need a booster to detonate it, like
picric acid. |
Nice.
Since you mentioned solubility, how soluble is SADS in ethanol, acetone and other solvents? The wikipedia article states that it is insoluble in
water.
If it is insoluble in ethanol, it is indeed a good choice of chemical, since it would dry the SADS much faster than water.
How much SADS can I store safely together, in the same container?
Thanks! |
SADS is pretty much insoluble in any solvent except very basic or acidic ones...
SADS is silver acetylide double salt or SANC silver acetylide nitrato complex... it is related to silver acetylide but it is not the same.
SA = Ag2C2
SANC/SADS = Ag2C2.xAgNO3 or Ag2C2.xAgNO3.yHNO3
The fact SANC/SADS contains nitrate into its complex structure allows form more energetic output and power... since the oxygen will help burning part
of the acetylen carbonaceous fuel... but not all as proven by the fact that the addition of KClO3 increases the power up to 40% by weight vs plain
SADS/SANC ==> so not enough oxydizer present for perfect OB (oxygen balance)
There are plenty of info about it all over the energetic section ==> Use the search engine
==> The safe amount to handle depends onto the operator, his ability to make the product pure following good procedures and onto the container.
I have had more than 15 grams stored at the same place under a granulated form with finer powder parts for long time.
Avoid light exposure for too long especially strong halogen ones and UV (like from the sun)... avoid too much friction, shock and heat... 150°C can
set it off.
[Edited on 3-10-2017 by PHILOU Zrealone] |
Thanks for the info.
Do I synthesize SADS from SA or I have to approach it differently?
|
|
|
PHILOU Zrealone
International Hazard
Posts: 2893
Registered: 20-5-2002
Location: Brussel
Member Is Offline
Mood: Bis-diazo-dinitro-hydroquinonic
|
|
| Quote: Originally posted by joseph6355 | | Quote: Originally posted by PHILOU Zrealone | | Quote: Originally posted by joseph6355 | | Quote: Originally posted by kratomiter |
My SADS is stable enough stored under ethanol in a dark place. I think dunnite is quiet insensitive, maybe you need a booster to detonate it, like
picric acid. |
Nice.
Since you mentioned solubility, how soluble is SADS in ethanol, acetone and other solvents? The wikipedia article states that it is insoluble in
water.
If it is insoluble in ethanol, it is indeed a good choice of chemical, since it would dry the SADS much faster than water.
How much SADS can I store safely together, in the same container?
Thanks! |
SADS is pretty much insoluble in any solvent except very basic or acidic ones...
SADS is silver acetylide double salt or SANC silver acetylide nitrato complex... it is related to silver acetylide but it is not the same.
SA = Ag2C2
SANC/SADS = Ag2C2.xAgNO3 or Ag2C2.xAgNO3.yHNO3
The fact SANC/SADS contains nitrate into its complex structure allows form more energetic output and power... since the oxygen will help burning part
of the acetylen carbonaceous fuel... but not all as proven by the fact that the addition of KClO3 increases the power up to 40% by weight vs plain
SADS/SANC ==> so not enough oxydizer present for perfect OB (oxygen balance)
There are plenty of info about it all over the energetic section ==> Use the search engine
==> The safe amount to handle depends onto the operator, his ability to make the product pure following good procedures and onto the container.
I have had more than 15 grams stored at the same place under a granulated form with finer powder parts for long time.
Avoid light exposure for too long especially strong halogen ones and UV (like from the sun)... avoid too much friction, shock and heat... 150°C can
set it off.
[Edited on 3-10-2017 by PHILOU Zrealone] |
Thanks for the info.
Do I synthesize SADS from SA or I have to approach it differently?
|
As explained the search engine is your friend...
Ag2C2.x AgNO3 - SADS - SANC
PH Z (PHILOU Zrealone)
"Physic is all what never works; Chemistry is all what stinks and explodes!"-"Life that deadly disease, sexually transmitted."(W.Allen)
|
|
|
Hexogen
Harmless
Posts: 6
Registered: 10-10-2017
Member Is Offline
Mood: No Mood
|
|
Armstrong's mixture, powerful primary ?
I understand the instability of Armstrong's mixture due to it composing of a strong oxidizer and red phosphorous.
Would it be possible to set off a mix of 9:1 mix of KClO3 and PIB
(Polyisobutylene) ?
|
|
|
Bert
|
Threads Merged
10-10-2017 at 20:35 |
magyarvegyesz
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
Amstrong's mix is very sensitive, if i where you i don't use it for primer. There are some less sensitive and easy to prepare primers that you can
use.
|
|
|
| Pages:
1
..
54
55
56
57
58
..
81 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
