PumpkinDad
Harmless
Posts: 4
Registered: 23-1-2016
Member Is Offline
Mood: No Mood
|
|
Buchi rotovap - slipping belt drive
Hi everyone,
I have an old Buchi R-124 Rotovap. After about an hour or so of operation, the belt drive begins to slip. The evaporation flask stops suddenly, then
rotation starts again in about a second.
I'm wondering what might be the cause of this and how I could go about fixing it?
Thanks,
PD
|
|
|
Zephyr
Hazard to Others
Posts: 341
Registered: 30-8-2013
Location: Seattle, WA
Member Is Offline
|
|
Very hard to diagnose without any photos, I have some experience with rotovaps, and if I could have a look I could probably find you a fix.
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Well with any belt drives you can try cleaning it all with isopropyle alcohol that the belt rides on, All so belt deflection should be less then a 1/4
inch.
Check the rotating berrings, ensure they ride smooth.
It is a simple mechanical system, so treat the common belt issues that can effect such a system.
If the belt deflection is out of spec, you can use a belt dressing spry but order a new belt now as yours is ready to go (Providing there is no option
to adjust tension)
But given the nature of the device I'd look at the rotating barring first.
http://www.ebay.com/itm/Buchi-R-124-Rotavapor-Evaporator-PAR... < For parts if needed.
[Edited on 23-1-2016 by XeonTheMGPony]
|
|
|
PumpkinDad
Harmless
Posts: 4
Registered: 23-1-2016
Member Is Offline
Mood: No Mood
|
|
Hi everyone,
Sorry for the delayed response. I got called away on business.
I couldn't figure out how to open up the drive unit on the R-124. There are two large screws but I can't get them to loosen up for the life of me.
I was contemplating forcing it, but then I saw an old R-124 unit for parts for sale on eBay and got it for a great price ($80). I swapped out the
drive unit and while I still have to do a vacuum test, it rotates perfectly.
PD
|
|
|
XeonTheMGPony
International Hazard
Posts: 1640
Registered: 5-1-2016
Member Is Offline
Mood: No Mood
|
|
Do not toss the drive, practice working on it.
|
|
|
PumpkinDad
Harmless
Posts: 4
Registered: 23-1-2016
Member Is Offline
Mood: No Mood
|
|
Absolutely... I would never toss a working part. Only problem is I can't figure out how to get it open. The two screws seem like an obvious way in,
but I can't get them to loosen up for the life of me.
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
Can you be sure the source of the rotation stopping is the drive slipping? Many times removal of the rotating tube from its assembly and cleaning it
will get a rotovap that stopped rotating back in working order.
|
|
|
PumpkinDad
Harmless
Posts: 4
Registered: 23-1-2016
Member Is Offline
Mood: No Mood
|
|
Oh, I didn't know that. Well, I already replaced the drive so if the problem returns, I will take clean the vapor duct and see if that fixes it.
Thanks for the tip!
PD
|
|
|
youtubechem
Harmless
Posts: 3
Registered: 27-1-2017
Member Is Offline
Mood: No Mood
|
|
Did you ever find out how to get in?
I have bought the 111 model and it turns intermittently the fan on the back of the motor stops turning as well.. I was told to grease the bearings but
can't find my way into the thing.
|
|
|
Corrosive Joeseph
National Hazard
Posts: 915
Registered: 17-5-2015
Location: The Other Place
Member Is Offline
Mood: Cyclic
|
|
Quote: Originally posted by youtubechem  | | I have bought the 111 model and it turns intermittently the fan on the back of the motor stops turning as well.. I was told to grease the bearings but
can't find my way into the thing. |
We had this issue lately on an old RE-111 l found.......... it would stop turning intermittently, but only on low speeds.........
We took the motor off for a look, and not wanting to dog the bejaysus out of it, couldn't get the bearing out..............
So we managed to squirt quite a bit of 3-in-1 (machine) oil in the motor shaft hole, on to the bearing race, whilst turning it by hand......... This
was followed by a good soaking of penetrating fluid (WD-40), in the hope that the WD would slightly thin the machine oil and drive it in there, all
the while, turning the bearing by hand back and forth (and round and round), hoping to work it in...............
We then let all the excess oil drip dry, and wiped down the casing with a dry cloth to clean it up. We put the whole thing back together, fired it up
and.............
Bingo, no more sticky bearing.............. Looks like this old Rotovap is gonna live a while longer..............
Hope this helps...................
/CJ
Being well adjusted to a sick society is no measure of one's mental health
|
|
|
youtubechem
Harmless
Posts: 3
Registered: 27-1-2017
Member Is Offline
Mood: No Mood
|
|
Which screws?
How do you gain access to the bearings?
|
|
|
youtubechem
Harmless
Posts: 3
Registered: 27-1-2017
Member Is Offline
Mood: No Mood
|
|
My bad
After purchasing another faulty RE 111 from ebay I found the courage to dissect the newer one, which seemed to be more defunct. I was able to get the
motor and screw gear apart and noted it was funky inside and the motor bearings were likely shot as well. Should I continue the tear down and replace
the motor bearings or are they "not user serviceable"?
|
|
|
Corrosive Joeseph
National Hazard
Posts: 915
Registered: 17-5-2015
Location: The Other Place
Member Is Offline
Mood: Cyclic
|
|
Buchi Rotavapor RE-111, RE-121 and EL-131 Manual..................
Attachment: Buchi Rotavapor RE-111, RE-121 and EL131 Manual.pdf (2.7MB)
This file has been downloaded 2307 times
/CJ
Being well adjusted to a sick society is no measure of one's mental health
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
