dermolotov
Hazard to Others
Posts: 114
Registered: 13-12-2014
Location: Toronto, Canada
Member Is Offline
Mood: Free
|
|
Reusing Column Silica
That stuff is expensive and it'd be quite effective to find a method to reuse silica.
Has anyone done this before? There's always the little disk of junk on the top layer but I'm talking more about soaking it in a giant vat of solvent
and perhaps distilling it off then rewashing it. Much like a soxhlet extractor but reverse?
I already do that with my TLC plates (just let them develop in a chambre overnight). Finding a method to clean silica would be quite nice.
|
|
|
BromicAcid
International Hazard
Posts: 3245
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Depends on what you are running through your column and how tightly it is bound. Even though you are leaving a layer at the top you don't know what
is between the top and the bottom, sometimes just throwing a black light on it will show you plenty of bands. I have seen columns setup and after the
target compound is off them the polarity of solvent is increased or decreased to 'flush' the column and then it is used in place as is (usually for
the same thing). You could wash it and filter it, I'm sure that would help, but you wouldn't want to distill it off, you'll leave your crap in with
your silica gel. Instead of running something "soxhlet extractor but reverse" a soxhlet extractor is exactly what you would be looking for except
that your solvent probably won't percholate through your silica gel that quickly.
PS: If you really are capturing your impurities at the top of your column then don't bother with the column, just shoot it through a silica gel plug.
|
|
|
dermolotov
Hazard to Others
Posts: 114
Registered: 13-12-2014
Location: Toronto, Canada
Member Is Offline
Mood: Free
|
|
A better explanation.
Quote: Originally posted by BromicAcid  | Depends on what you are running through your column and how tightly it is bound. Even though you are leaving a layer at the top you don't know what
is between the top and the bottom, sometimes just throwing a black light on it will show you plenty of bands. I have seen columns setup and after the
target compound is off them the polarity of solvent is increased or decreased to 'flush' the column and then it is used in place as is (usually for
the same thing). You could wash it and filter it, I'm sure that would help, but you wouldn't want to distill it off, you'll leave your crap in with
your silica gel. Instead of running something "soxhlet extractor but reverse" a soxhlet extractor is exactly what you would be looking for except
that your solvent probably won't percholate through your silica gel that quickly.
PS: If you really are capturing your impurities at the top of your column then don't bother with the column, just shoot it through a silica gel plug.
|
My explanation was inept. Sorry.
If my mixture was unburnt and stable (most lab procedures like demethylation, PCC, high temperature DMSO reflux, etc leaves behinds the black gunk
that stays at the top of the silica), could I just stir the silica in excess aluent, decant into a rotovap, then pour the remaining solution back into
the silica vessel to soak/stir and repeat that to wash it through? That should release any adsorbed spots, right?
I guess you are right with the whole "case by case" situation.
www.alchemylabsupply.com/
Product Director
Canadian Chemical Legal Liaison
Sales Expert
Amateur Munitions/Explosive Expert
Safety Coordinator
Walking Oxymoron
|
|
|
Dr.Bob
International Hazard
Posts: 2732
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Years ago, my professor used to save the bulk of the used silica gel (most guys would ditch the top 1/2" of the material, as that is where most of the
trash gets bound), wash it well, heat it to a high temp in a vacuum oven, and then reuse it for non-critical stuff.
|
|
|
dermolotov
Hazard to Others
Posts: 114
Registered: 13-12-2014
Location: Toronto, Canada
Member Is Offline
Mood: Free
|
|
| Quote: Originally posted by Dr.Bob | | Years ago, my professor used to save the bulk of the used silica gel (most guys would ditch the top 1/2" of the material, as that is where most of the
trash gets bound), wash it well, heat it to a high temp in a vacuum oven, and then reuse it for non-critical stuff. |
Good to know it kinda works. Much like reusing silica plates, I suppose it's worth salvaging for non-critical stuff, as you mentioned. I guess he
wasn't working with fluorescing materials, too that'd be adsorbed and dye the stuff everywhere.
If only I could get academia prices for their drums of silica gel. It's $100 for 2kilos here!  . Ah well, 'tis the price of the trade.
How did he efficiently remove all the top 1cm anyway? Especially when plopped in the column like so.
www.alchemylabsupply.com/
Product Director
Canadian Chemical Legal Liaison
Sales Expert
Amateur Munitions/Explosive Expert
Safety Coordinator
Walking Oxymoron
|
|
|
Dr.Bob
International Hazard
Posts: 2732
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
It was not an exact science to get rid of the to bit of silica. If the column is damp, and you blow the silica out of it slowly with air, you just
let the first glop go to the solid waste, then collect the rest. That also gets rid of any sand from the top. If it is try, it just takes a
careful rotation of the column to keep the top material coming out first, and that helps some as well. If you heat the silica enough in a drying
oven, it will burn off most of the remaining organics, but you want to make sure no solvent is left in it when you do that. Even "academic" prices
for silica are very high, at least from my experience, so I try to use a plug to remove most of the baseline material when possible, and then
crystallize products or use the smallest column that I think will work for products. Often if you can get a material mostly pure with a small
column, then it will readily crystallize and then the mother liqueurs can be re-purified later if needed. A lot depends on if you are scaling up the
same things over and over, or making a new compound each reaction. Lots of product variety makes it much harder to save silica gel.
Have you tried Silicycle? They are in Canada, make their own silica gel, and sometimes are flexible on pricing. You might be able to get some old
materials or an off spec batch cheap. I have used their products before, and they have some great stuff, but more expensive in the US than US made
materials.
|
|
|
dermolotov
Hazard to Others
Posts: 114
Registered: 13-12-2014
Location: Toronto, Canada
Member Is Offline
Mood: Free
|
|
| Quote: Originally posted by Dr.Bob | | It was not an exact science to get rid of the to bit of silica. If the column is damp, and you blow the silica out of it slowly with air, you just
let the first glop go to the solid waste, then collect the rest. That also gets rid of any sand from the top. If it is try, it just takes a
careful rotation of the column to keep the top material coming out first, and that helps some as well. If you heat the silica enough in a drying
oven, it will burn off most of the remaining organics, but you want to make sure no solvent is left in it when you do that. |
Darn it! The issue is that I have a solvent reservoir so it's pretty hard to skim wet silica. I only have one column (3cm) that is a straight column
with no bulb at the end. I'll figure a way out. I seem to always do..
Thanks for the recommendation as well as the source of silica. I'll check into them. I'll check them out!
Currently, I pay $100/ 500g of 60-200mesh silica. 
www.alchemylabsupply.com/
Product Director
Canadian Chemical Legal Liaison
Sales Expert
Amateur Munitions/Explosive Expert
Safety Coordinator
Walking Oxymoron
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
There is no universal way to reuse silica as others have noted. The same rules that apply to fritted filters apply here. If it is just relatively low
boiling point organics then slow baking is your friend. If it is stuff that will carbonize or inorganics then it is really difficult to clean.
Organometalics are practically impossible to remove. The stuff that will carbonize can be cleaned out with pirahna solution made from vaccuum
distilled hydrogen peroxide and vacuum distilled sulfuric acid. But then you have to remove the sulfuric acid. Triple distilled water using
glassware is good for this as silica will be the only major contaminant. If you are cleaning the stuff up with a solvent you are likely to spend more
on solvent than new silica. Chromatography grade solvent is required and that is expensive.
|
|
|
Morkva
Harmless
Posts: 17
Registered: 6-11-2014
Member Is Offline
Mood: No Mood
|
|
Will ozone destroy C/H/N/O compounds in enough time? Silica catalyzes the decomposition of ozone, and there is a lot of silica, but you might still
get it to work.
[Edited on 2-1-2016 by Morkva]
http://www.carrotmuseum.co.uk/falcarinol.html
“Science is the ultimate pornography, analytic activity whose main aim is to isolate objects or events from their contexts in time and space. This
obsession with the specific activity of quantified functions is what science shares with pornography.”
- J.G. Ballard, The Atrocity Exhibition
|
|
|
macckone
Dispenser of practical lab wisdom
Posts: 2168
Registered: 1-3-2013
Location: Over a mile high
Member Is Offline
Mood: Electrical
|
|
Ozone will react with carbonized crap but it isn't going to penetrate into silica due to the catalytic action. So you would need a really thin layer.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
