196
Harmless
Posts: 2
Registered: 21-8-2015
Member Is Offline
Mood: No Mood
|
|
Leaky Joints
Today I was making some nitric acid with sulfuric acid and potassium nitrate. I know it's been done a lot on the Internet before, but in the middle of
the distillation some nitric acid vapors and nitrogen oxides started leaking out of the joint between the 75 degree adapter and the condenser, and to
a lesser extent the joint at the reaction flask and the bottom of the adapter.
As still somewhat of a beginner in amateur chemistry work, I was just wondering what you all thought may have caused the leaking. This was my first
time using some Chinese glass I'd gotten off eBay, though the seals initially seemed reasonably tight, at least at the joints that were leaking. I
also greased the joints with some sulfuric acid although it didn't seem to stop the vapors from seeping through and escaping.
Thanks.
|
|
|
Detonationology
Hazard to Others
Posts: 362
Registered: 5-5-2015
Location: Deep South
Member Is Offline
Mood: Electrophillic
|
|
I too purchased some glassware from China from 2 different suppliers. Simply put, the so called Standard Taper was not up to standard. There was a a
very loose fit towards the bottom of the taper. Did you use keck clips to secure the joints? A high-temp grease made by Corning solves most leak
issues, and it's fairly inert. I've also heard of someone who purchased glassware with "unfrosted" joints, but I have never stumbled upon one without
the frosting. Also, a vacuum pump or aspirator can be used to seal the joints and pull off the nasty NOx fumes.
[Edited on 11-4-2015 by Detonationology]
“There are no differences but differences of degree between different degrees of difference and no difference.” ― William James
|
|
|
Agari
Banned
Posts: 160
Registered: 8-10-2015
Location: The Amine Group
Member Is Offline
Mood: Lowest Oxidation State
|
|
Dow Corning High-Vacuum grease does the job for me and is in fact relatively inert, as I did not get any noticeable contamination when performing
chemistry experiments.
Unrelated: Does anybody know what hydrogen fluoride smells like,or is it odorless?
[Edited on 4-11-2015 by Agari]
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Plumber's teflon tape is effective too, and cheaper than HV grease . . . ?
|
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I don't know what it smells like, but I highly doubt that hydrogen fluoride is odorless.
|
|
|
arkoma
Redneck Overlord
Posts: 1762
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
Used PTFE tape myself. Works great.
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
|
szuko03
Hazard to Others
Posts: 188
Registered: 3-4-2015
Location: USA
Member Is Offline
Mood: No Mood
|
|
I am all for that tape. I just experienced it the for the first time today and it is definitely made for this type of application.
Chemistry is a natural drive, not an interest.
|
|
|
Deathunter88
National Hazard
Posts: 519
Registered: 20-2-2015
Location: Beijing, China
Member Is Offline
Mood: No Mood
|
|
Just FYI, glassware in China 24/29, not 24/40. Don't know about how much of a difference that makes.
|
|
|
Amos
International Hazard
Posts: 1406
Registered: 25-3-2014
Location: Yes
Member Is Offline
Mood: No
|
|
Weird thread to ask this in, but I've smelled it before and it's similar to hydrogen chloride but more biting and unpleasant.
|
|
|
Agari
Banned
Posts: 160
Registered: 8-10-2015
Location: The Amine Group
Member Is Offline
Mood: Lowest Oxidation State
|
|
Quote: Originally posted by Amos  |
Weird thread to ask this in, but I've smelled it before and it's similar to hydrogen chloride but more biting and unpleasant. |
What were you doing that exposed you to a sufficient concentration of HF that you could smell it?
Edit:Is HF gas also rapidly absorbed through the skin like its aqueous form?
[Edited on 5-11-2015 by Agari]
|
|
|
Agari
Banned
Posts: 160
Registered: 8-10-2015
Location: The Amine Group
Member Is Offline
Mood: Lowest Oxidation State
|
|
You never know,maybe it causes rapid olfactory fatigue like hydrogen sulfide.
Nevermind, Amos already provided an answer.
|
|
|
Agari
Banned
Posts: 160
Registered: 8-10-2015
Location: The Amine Group
Member Is Offline
Mood: Lowest Oxidation State
|
|
| Quote: Originally posted by szuko03 | | I am all for that tape. I just experienced it the for the first time today and it is definitely made for this type of application.
|
Never tried teflon tape,but seeing as a large amount of stir bars are coated in teflon to prevent reaction(And mostly do not receive damage unless
used with liquid alkali metals),I would assume that it would work.
|
|
|
Upsilon
Hazard to Others
Posts: 392
Registered: 6-10-2013
Member Is Offline
Mood: No Mood
|
|
This only happens at higher concentrations of H2S. You can consistently keep smelling it at low concentrations without a health risk. While some
sources say that this deadening of sense of smell makes it very hazardous, I see it as a benefit - you know when you stop smelling it that you need to
GTFO fast.
|
|
|
Agari
Banned
Posts: 160
Registered: 8-10-2015
Location: The Amine Group
Member Is Offline
Mood: Lowest Oxidation State
|
|
| Quote: Originally posted by Upsilon |
This only happens at higher concentrations of H2S. You can consistently keep smelling it at low concentrations without a health risk. While some
sources say that this deadening of sense of smell makes it very hazardous, I see it as a benefit - you know when you stop smelling it that you need to
GTFO fast. |
That is true,but when we don't smell something,we generally do not think about it and it is easy to forget that a toxic gas is present in the
atmosphere unless you smell it or keep constantly reminding yourself that you are working with hydrogen sulfide.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
