Alek
Harmless
Posts: 4
Registered: 22-3-2005
Location: Poland
Member Is Offline
Mood: No Mood
|
|
Measuring pressure a la Pirani's Vacuum Meter
Hi,
My name is Alek Zawada. I'm polish. My english is very fatal . I'm so
sorry
That's why I beg you:
don't write a lot of very hard words.
I have the vacuum pump. It isn't very good pump, because I have
70 torr vacuum (760 torr=760mmHg=1013,25hPa). However I haven't
very high vacuum it's posibble to make the tubes with cold cathode.
I can to do it.
I measure my vacuum by mechanical vacuum meter, but it isn't good idea.
Why? Because this vacuum meter is big. I tried to do better vacuum meter-
Pirani's vacuum meter. (I reconstructed ligtbulb-I united the glass tube with bulb).
Metal wire in the bulb must be hot (mabye 400 celsus degrees it's good -then wolframe
couldn't burn). That's why you must to connect the serial resistor to reduce current.
Now, If you reduce the pressure inside the bulb, resistance of metal wire in bulb will be
grow up (because gas cool down the wire worse nad worse). It's no problem to compute the resitance to presure and display it on LCD.
But I don't know if displayed pressure (vacuum) depend on atmospheric pressure.
What do you think about it?
If you want, you can see my glass tubes here (there is in the file *.jpg
http://www.trioda.com/php/forum/viewtopic.php?t=638&post...
Edited by chemoleo: Changed title to something more appropriate.
[Edited on 23-3-2005 by chemoleo]
|
|
|
chemoleo
Biochemicus Energeticus
Posts: 3005
Registered: 23-7-2003
Location: England Germany
Member Is Offline
Mood: crystalline
|
|
It's a good question.
Could you please point out which picture you mean, there are several.
Hmm, so essentially you say resistance in Ohms changes within the wire depending on the pressure (concentration of gas) the wire is surrounded by?
Essentially, a higher pressure would mean more rapid cooling, while a cooler wire would mean a smaller resistance (a red glowing wire has a greater
resistance than a cool one)- which results in a resistance being somewhat proportional to the pressure? Proportional...uhm. I doubt it.
You'd need to derive the equations for that. The system needs to be calibrated naturally, if the lightbulb i.e. had the size of a room, the
cooling would be more efficient (and thus the resistance proportional to the pressure, taking some gas/electric laws into account?) because the heat
generated by it would not be able to feed back into the system so quickly.
So there are lots of factors to take account of.
Essentially, yes, the resistance depends to some degree on the pressure; the higher the pressure, the smaller the resistance.
So a vacuum insulates perfectly, causing the resistance to increase (because it can heat up, without the heat being carried away by gasses).
But unless you have a perfect system, I think you'd need calibration (of known pressures) to make this work.
I like the idea though
Do correct me if I misunderstood or something.
[Edited on 23-3-2005 by chemoleo]
Never Stop to Begin, and Never Begin to Stop...
Tolerance is good. But not with the intolerant! (Wilhelm Busch)
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
The displayed pressure will depend less on atmospheric pressure, and more on atmospheric temperature.
A better way to run a Pirani gauge is to run it so that its temperature (resistance) stays constant and then measure the power needed to keep that
temperature.
Have a look here for a thermistor gauge that works on the same principle
|
|
|
Alek
Harmless
Posts: 4
Registered: 22-3-2005
Location: Poland
Member Is Offline
Mood: No Mood
|
|
Good morning!
Thank you for answeres. I watch Twospoons's link. It i'snt exactly my idea, because I haven't thermocouple in my bulb.
My sample schematic diagram is here:
http://www.trioda.com/php/forum/viewtopic.php?t=638&star...
(the file called "wakuometr idea.jpg".
In my circuit, the metal wire have resistance:
R=Ro(1+kT)
when k-constant
Ro-resistance in temperature=0 celsus degrees
T-temperature (depend on presure )
If pressure fall from ca.760 Torr to ca.76 Torr the current in microamperometer change of 100 microamperes. Firstly, I couldn't belive that
it's possible- I though that Pirani's vacuum meter is good for low pressure (for example 10^-2 torr) only.
I'm going to reconstruct my circuit - I will have to add operational amplifier, microcontroller, LCD display etc.
I'm afraid that use thermocopule is better idea- we haven't errors from temperature of atmosphere.
|
|
|
Twospoons
International Hazard
Posts: 1324
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
This is closer to what you are doing. In this circuit the bridge is kept in balance by the amplifier, and the bridge excitation voltage gives you a measure of the pressure.
Since you are using a filament instead of an NTC thermistor, you would need change the circuit - put your filament in the upper arm of the bridge in
place of R1.
|
|
|
Geomancer
Hazard to Others
Posts: 228
Registered: 21-12-2003
Member Is Offline
Mood: No Mood
|
|
That's an impressive bit of glassblowing. Scientific American had a column describing a Pirani gauge in the November 1996 issue. The
sensor was a "glow plug" for some sort of model engine, but I assume the calibration and electronics will be similar. I don't have a
copy right now, so that is all I can tell you. I can probably give some more details on Monday.
|
|
|
Alek
Harmless
Posts: 4
Registered: 22-3-2005
Location: Poland
Member Is Offline
Mood: No Mood
|
|
Having some time I'm making the system with LCD 2*16, microcontroller ATMEGA 8 and precision amplifier MAX 430. Writing the program I used
polynomial (5 stage) to change voltage to pressure. I'm happy, because it's working good!
Geomancer-I will be waiting for your answer.
|
|
|
Texium
|
Thread Moved
19-11-2023 at 10:24 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
