Reverend Necroticus Rex
Hazard to Others
Posts: 196
Registered: 15-6-2004
Location: Right behind you.......
Member Is Offline
Mood: Poisonous
|
|
Large scale amateur alkali buissiness
I am hoping to set up a small buissiness soon, producing alkali metals on a large scale, to sell, for the purposes of boosting up my rather meager
income as I am currently on benefit for all the money I get.
The way I intend on doing this, is modifying a series of large fishtanks, to hold anodes at the bottom,
and create a large series of cells with multiple carbon anodes submerged in tanks of pyridine, saturated with caesium, rubidium, potassium and sodium
salts, and may create a smaller tank for the preperation of lithium metal, and run it off a generator using cheap fuel, for the caesium, build a tap
in the bottom of the tank, to enable running off of the liquid caesium as it is formed, having all the cells containing 20 liters of pyridine, to act
as a solvent for electrolysis which will not attack the metal, a closed system, to prevent escape of stinky and toxic pyridine, and a hatch, to permit
intake of further metal salts, and an escape valve, built into a single cathode barely touching the surface of the stinky lake of fishy death within,
and performing the electrolysis using the chloride salts of the metals.
I have a few questions, and would like input as to optimisations I might make, the cathode will barely touch the pyridine, so that the evolved
chlorine gas can simply be run off without reacting with the solvent, therefor minimising maintainance, and then, run off into a large drum kept full
of very hot saturated KOH solution, to absorb the Cl2, and also yield large quantities of potassium chlorate as a byproduct, that can be sold for
further profit, or perhaps, directly liquify the chlorine in diving gas cylinders, and either sell or use it for my own projects
I hope, to be able to output multiple-tens-of-kilograms quantities of potassium, sodium and caesium metal, and produce rubidium and lithium in any
quantity to order, after a first, several kilogram test run of the production process to produce some Rb and Li to be able to satisfy any reasonably
sized orders at short notice if I must do.
I would quite like others input on this, I am serious about investing in the stuff needed to create a large-scale home lab manufacture of the group
one metals, and equally as serious about selling them for profit, so, if anybody has any suggestions as to how I might improve my setup, I would be
very glad to hear of them.
I will probably be selling via Ebay, and, if I manage to get this set up, I will be willing to give any scimadness members, with at least one
non-troll post a discout
[Edited on 21-3-2005 by Reverend Necroticus Rex]
The sun is shining on a brand new day
Blackened corpses burn where they were slain
Self-flagellation prompts him to confess, Bless me father, for I made this mess.
|
|
|
BromicAcid
International Hazard
Posts: 3253
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
From what I have read on electrolysis of the alkali metal salts in pyridine nearly every source that I have found says that electrolysis of lithium
salts works better then any of the other alkali metals, one member of our forum Strepta, had this to say in the lithium production thread on
it: | Quote: | | Last December I thought I'd try the electrolysis of LiCl in pyridine, so I purchased 500ml of pyridine for $60 (ouch!!) I used a graphite anode
and a nickel cathode (approx. 2 sq. in.) Spacing between electrodes was about .75 in. I was able to dissolve 2 g of LiCl in 30 ml of pyridine.
Applying voltage, I could hardly detect any current flowing. For 30v across the electrodes there was perhaps 15ma of current. The LiCl must not be
ionized. Doing a little math after the fact, it takes about 100,000 coulombs to reduce a mole (7 grams) of Li+ ions to Li. At .015A that would take
about 2000 hours or much larger plates and I have better things to do. Also, pyridine is not all that pleasant to have around as it smells a lot like
skunk. Live and learn I guess. |
Larger amounts of pyridine may lead to larger solutions and maybe better
current efficency, however if your anode is only going to barely touch the pyridine then your current going through the solution is going to suffer.
Because the conductivity of these solutions is so bad usually they use very large flat graphite plates to get the best current out of the system
possible. Good luck.
BTW, S.C. Wack followed up to Strepta's post above with this | Quote: | | I read his articles (there are later ones in that journal) and thought that there may be some cottage-industryness to it if there was enough demand
and cheap electricity. But if I remember correctly, it is a very touchy procedure, for several reasons. The pyridine must be very dry, and stay that
way. He did not get good results with the other solvents, either. Would take some work, and this would probably not be a side project, but something
you would devote a lot of effort towards, like Kahlenberg did. |
[Edited on 3/21/2005 by BromicAcid]
|
|
|
Reverend Necroticus Rex
Hazard to Others
Posts: 196
Registered: 15-6-2004
Location: Right behind you.......
Member Is Offline
Mood: Poisonous
|
|
Hmm, what about using a large, flat, slotted or perforated graphite plate, or what about silver, sheets of silver foil could be arranged in large
metal frames, to avoid tearing and would give good conduction area for relatively little price.
I think, given low solubility of the salts in pyridine, a co-solvent, mixed with the pyridine might work to imprive the yield,
I am looking up online to see what I can dig up now on the matter of a cosolvent,
I think, perhaps, I would rather use one large tank, to increase efficiency, and prepare one metal at a time, to order, rather than multiple 20-liter
tanks, have one, 100 liter tank, with a very large surface area of the electrodes using foil or thin, but large diameter graphite plates.
What about other alkali metal compounds, are the hydroxides soluable in pyridine? although I don't much fancy trying to dry out 100 liters of wet
pyridine after the water byproduct of the electrolysis of the hydroxide started to foul things up
The sun is shining on a brand new day
Blackened corpses burn where they were slain
Self-flagellation prompts him to confess, Bless me father, for I made this mess.
|
|
|
rift valley
Hazard to Others
Posts: 103
Registered: 24-7-2004
Location: NH
Member Is Offline
Mood: semiconducting
|
|
Damn you're not messing around 20L of pyridine goes for around $1400 (US) Gallade Chemical . Sounds like a big initial investment to get your
operation started, but maybe once started it will be easy to maintain? Have you performed experiments involving electrolysis of alkali ions in
pyridine before? If you decide to go through with this more power to you 
P.S. Can I put my name on the list for potassium metal please 
EDIT: I spoke too soon, it seems 200L can be had for $4500, altough nothing to sneeze at it is still much cheaper then the price I quoted above 200L pyridine
[Edited on 21-3-2005 by rift valley]
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
You may have to go on a smaller scale for the Cs production. Have you checked the prices on any caesium salts lately.
|
|
|
S.C. Wack
bibliomaster
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
I'm not sure what all articles I was talking about, I didn't keep track of what they were. A quick non-authoritative search yielded:
http://gallica.bnf.fr/catalog?IdentPerio=NP00348
J. Phys. Chem. 3, 602 (1899)
8, 153 (1904)
12, 49 (1908)
but there are others, somewhere. I'm pretty sure this isn't going to happen.
|
|
|
Reverend Necroticus Rex
Hazard to Others
Posts: 196
Registered: 15-6-2004
Location: Right behind you.......
Member Is Offline
Mood: Poisonous
|
|
Well, my father is arranging to get me 100ml or so of pyridine hopefully, to do some preliminary testing and experimentation, to find a decent
co-solvent to ionise the salts more efficiently.
He said to me, he is willing to help, even to the extent of me getting a small shed to function as a lab, so long as I can produce, and sell, a small
sample of an alkali metal, I am thinking ten grams or so to begin with for proof of concept.
Rogue Chemist, I noticed, that the link you provided for pyridine, was of the ACS grade, I am sure pyridine can be had for cheaper, it doesn't
need to be analytical grade of course, merely anhydrous.
Can pyridine be distilled over CaCl2? or are molecular sives needed for drying?
SC.Whack, you couldn't perhaps post the full text of those journal references could you, I can only access the abstracts, which provide no
information.
[Edited on 21-3-2005 by Reverend Necroticus Rex]
[Edited on 21-3-2005 by Reverend Necroticus Rex]
The sun is shining on a brand new day
Blackened corpses burn where they were slain
Self-flagellation prompts him to confess, Bless me father, for I made this mess.
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
Reverend, you gave the credit to the wrong guy, rift valley linked you to the pyridine page.
I did a bit of looking around and cesium salts range in price from 1-2$ per gram. You might to make sure your setup works well with the other alkalis first before you invest in large ammounts of cesium compounds.
|
|
|
Antwain
Hazard to Others
Posts: 252
Registered: 21-7-2007
Location: Australia
Member Is Offline
Mood: Supersaturated
|
|
Sorry to revive an old thread and hijack it good but this last post is EXACTLY my problem.
WHY IN THE HELL IS CAESIUM SO GODDAM EXPENSIVE?
According to Wiki (I will trust it since they have multiple sources and differnt values in good agreement) it is ~10^2 times more prevalent in the
crust than silver. 1/5 as abundant as bromine!!!!!!!!!!
Bromine is going to be found in the same places as caesium, ie salt deposits. So why are we being reamed, and where can we go to not get reamed?
|
|
|
evil_lurker
National Hazard
Posts: 767
Registered: 12-3-2005
Location: United States of Elbonia
Member Is Offline
Mood: On the wagon again.
|
|
It could be that there is not a very large market for it, and quite possibly it presents purification issues.
Not all chemicals are bad. Without chemicals such as hydrogen and oxygen, for example, there would be no way to make water, a vital ingredient in
beer.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Caesium is so expensive in part because unlike silver it doesn't concentrate in ores that much, and it's not nearly as easy as silver to isolate as an
element or a compound of the element.
For silver a number of relatively simple chemical or thermochemical processes will give a crude high silver alloy. After that electrorefining using
aqueous electrolyte will give both pure silver and a byproduct of any gold and platinum metals that were in the crude alloy. Similarly
electrorefining of copper gives a byproduct of the precious metal content of the original ore.
Caesium, rubidium, and potassium stick together pretty well, in most places the concentration of Cs and Rb are rather low, and there's generally a lot
of sodium and lithium as well. It's just in a few alkali metal rich rocks that the Cs and Rb concentration is high enough to make it worth going
after. Bernic Lake in Canada has about 2/3 of the world's reserves of economically extractable caesium ore. And once you got the Cs and Rb out, you
have to isolate them via fractional crystallisation or other process that doesn't give clean separation in a single step.
Bromine is easy to extract from fairly dilute sources, blow chlorine and steam through the solution and collect the bromine vapours. Bromine is
extracted from brines with 4 to 5 parts per thousand of bromine, a fairly low concentration of target for most elements.
When it comes to elements or simple compounds, high prices generally don't mean you're being ripped off, but that it's difficult to obtain them and/or
the demand is low enough that extraction is on a small scale and hasn't been optimised. Caesium format drilling fluid runs some 4000 $US per barrel,
meaning that many operations use some alternative rather than showering the suppliers with their money; I'm sure the suppliers would like to have a
way to reduce the cost so they could sell more.
|
|
|
kilowatt
Hazard to Others
Posts: 322
Registered: 11-10-2007
Location: Montana
Member Is Offline
Mood: nitric
|
|
You could always make your own pyridine from ammonia or ammonium acetate (easy to make from the obvious), acetaldehyde (could be made through partial
oxidation of ethanol), and formaldehyde (easily purchased in the form of trioxane fuel tablets). http://en.wikipedia.org/wiki/Hantzsch_pyridine_synthesis
You can get cesium chloride for $235/kilo plus shipping (bringing it to about $250) from cesium-chloride.com, but...
If this pyridine electrolysis could be used at all to make the more reactive alkali metals, potassium, rubidium, and cesium, wouldn't they use it
industrially instead of fractional distillation of the metal from a fused salt bath with addition of liquid sodium? That process requires high
temperature, relatively complex apparatus, and has fairly low batch yield, with a continuous process involving continual removal of the fused salt and
fractional crystallization, prior to the addition of new salt. Especially considering the low demand of these metals and the fact that pyridine is
produced from such fundamental reagents, they would probably use it if it was even possible.
The mind cannot decide the truth; it can only find the truth.
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
Not really. Large quantities of pyridine would present difficulties that industries like to avoid: toxicity, environmental problems, flammability,
volatility.
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
kilowatt
Hazard to Others
Posts: 322
Registered: 11-10-2007
Location: Montana
Member Is Offline
Mood: nitric
|
|
It isn't as flammable, toxic, or otherwise insanely hazardous as cesium vapor...
[Edited on 16-10-2007 by kilowatt]
The mind cannot decide the truth; it can only find the truth.
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
Pyridine is both HIGHLY flammable and harmful. You'd better check an MSDS before messing around.
Other than that, Cesium is the desired product and can be sold. You don't want thousands of liters of harmful and flammable solvent in an industrial
environment which have to be processed and disposed of.
[Edited on 17-10-2007 by vulture]
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
kilowatt
Hazard to Others
Posts: 322
Registered: 11-10-2007
Location: Montana
Member Is Offline
Mood: nitric
|
|
I guess I'm not sure what the point of any of this is. Many industrial processes use dangerous reagents or equipment. Pyridine is nasty stuff but
certainly not alarming. It is mere childsplay compared with HCN, cyanogen, boranes, hydrazine, arsine, and many other industrial chemicals. They
usually use the most cost-effective method, but you're correct that environmental concerns can be an issue too. A large bath of pyridine is certainly
harder to legitimately dispose of than a batch of harmless salts at the end of the day.
Personally I am skeptical that this cold electrolysis method is viable, and its lack of use in industry is one reason why. However I do wish the best
of luck to anyone who tries it and would like to see some actual experiments with it. If cesium salts are relatively soluble in pyridine and it will
not react with cesium metal, it just might work out. I have too many other chemistry projects going now to even think about it, though. Being in
school, away from my lab, does not help.
The mind cannot decide the truth; it can only find the truth.
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
Don't look at the industry for lab scale preparations. The industry uses processes that are totally uneconomical (Haber-Bosch for example) on a lab
scale but work in large quantities. In a lab you'd make ammonia from an ammonium salt and a base, in the industry this is considered nuts.
| Quote: |
It is mere childsplay compared with HCN, cyanogen, boranes, hydrazine, arsine, and many other industrial chemicals. |
Correct, but they are usually a reagent which is consumed or for which there is no viable alternative. Neither is the case for pyridine.
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
Texium
|
Thread Moved
19-11-2023 at 12:10 |
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
