| Pages:
1
2 |
Scratch-
Hazard to Self
Posts: 60
Registered: 22-2-2005
Location: U.S.
Member Is Offline
Mood: No Mood
|
|
Liquid gasses
I have a list of gasses here that might be neat to ampoule while liquid. If you put a liquid gas in a container and seal it up it should remain a
liquid provided it cant break the container from the pressure and theres not enough room for it to totally expand and become a gas. So if you had some
ampoules made of thick thick glass you should be able to contain alot of the higher BP gasses. But the problem is that the only kind of ampoules I can
find are those that are sold for containing medicines to keep them sterile, these would be good maybe for holding gasses with a BP higher than 0
degrees but IDK besides that. Does anyone know where to get ampoules with thicker glass? Also a few more interesting gasses wouldnt hurt. 
(NOTE: some of these gasses would be hard to ampoule, like SO3, and some would be downright insane, like F2.)
Temp (C)............Composition
58.7.........................Br2
44.8.........................SO3
21.2.........................NO2
0..............................Ice and water (Cooling solution)
-7.............................NH3NO3 and water (Cooling solution)
-10.06......................SO2
-21...........................Ice and saturated NaCl solution (Cooling solution)
-33.34......................NH3
-34.06......................Cl2
-35.4........................HI
-40...........................Ice and saturated CaCl solution (Cooling solution)
-66.7........................HBr
-78...........................Dry ice and acetone (Cooling solution)
-85.06......................HCl
-88.6........................N2O
-108.1......................Xe
-151.7......................NO
-153.4......................Kr
-183.17....................O2
-185.86....................Ar
-188.2......................F2
-195.86....................N2
-195.86....................Liquid nitrogen (Cooling solution)
-246.06....................Ne
-252.8......................H2
-268.94....................He
An ampoule of liquid helium would be really neat. 
Sources:
Gas BPs: http://chemfinder.cambridgesoft.com/
Cooling solutions: https://www1.fishersci.com/education/resources/eqtip06.jsp
[EDIT: Corrected the BP of HI and removed O3, which decomposes when liquified]
[Edited on 3/11/2005 by Scratch-]
[Edited on 3/11/2005 by Scratch-]
|
|
|
neutrino
International Hazard
Posts: 1583
Registered: 20-8-2004
Location: USA
Member Is Offline
Mood: oscillating
|
|
| Quote: | Originally posted by Scratch-
If you put a liquid gas in a container and seal it up it should remain a liquid provided it cant break the container from the pressure and theres not
enough room for it to totally expand and become a gas. |
Any way you seal it, the gas will exert the same outward pressure—its vapor pressure. Since this increases with temperature, this means that you
will have a hard time ampouling any of the lower-boiling gasses without an explosion. Another problem: some of these gasses would become supercritical
fluids at room temperature, leaving you without a clearly defined liquid-gas boundary. This shouldn't be much of a problem, though, as this is
almost always at 25+ atm.
All of this aside, I have thought about ampouling liquid chlorine but can’t do it without dry ice. My idea was as follows: seal one end of a short
glass tube and extrude the other end into a capillary so the liquid could be pipetted in. Chill with dry ice, add liquid chlorine, and seal. So far, I
have only been able to do this with difluoroethane (Bp. -25*C), but chlorine should be doable, only having a vapor pressure of around 3-4 atm at room
temperature.
A word of advice on this: when sealing the ampoule, make sure that the liquid inside it doesn’t heat up. A slight increase in temperature of a
liquid near its boiling point causes a very large increase in vapor pressure. This inevitably bursts the bubble of molten glass at the top of the
ampoule (where it’s being sealed), ruining it. To avoid this, cool the liquid down a lot, seal the ampoule very quickly, use a very thin and hot
flame, get some glassworking experience, and if possible, ensure a distance of at least ¾” between the ampoule and liquid.
A thought about storage: could the ampoule be stored in a block of transparent plastic? It’s hard to describe, but I’m thinking of those blocks
the bugs in museums are always sealed in.
|
|
|
12AX7
Post Harlot
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
Just mind the critical temperature, above which it cannot be compressed into liquid form.
F2 can be stored gaseous for a little while (see www.theodoregray.com), under the pressure to keep it liquid or supercritical might be a bit harder though...
Tim
|
|
|
chemoleo
Biochemicus Energeticus
Posts: 3005
Registered: 23-7-2003
Location: England Germany
Member Is Offline
Mood: crystalline
|
|
Transparent plastic - hmm. Having had some experience with it, it always takes some time to harden (i.e. polyester resin). The more catalyst one adds
(MEKP), the faster the hardening, but it produces a big temperature spike. This is not good for the gas, and also it causes cracks. Foreign objects in
resin also require slow hardening, to avoid cracks (the object has different expansion coefficients than the resin). It'd be tricky to
do, but possibly worthwile if done well!
Never Stop to Begin, and Never Begin to Stop...
Tolerance is good. But not with the intolerant! (Wilhelm Busch)
|
|
|
a_bab
Hazard to Others
Posts: 458
Registered: 15-9-2002
Member Is Offline
Mood: Angry !!!!!111111...2?!
|
|
Most of the gases in your list are next to imposible to "ampoule".
With chlorine it is possible though. What you need is gases with a scritical temperature superior to the room temperature, and a
"liquification" presure with a value less then 5 atm let's say, so that the ampule will resist to the presure.
Liquid chlorine is an oily, green liquid...Very interesting to see I bet.
|
|
|
Scratch-
Hazard to Self
Posts: 60
Registered: 22-2-2005
Location: U.S.
Member Is Offline
Mood: No Mood
|
|
Yeah the lower temperature ones, but what about most of the ones above the dry ice/acetone mixture? I was thinking that those should be doable, but I
need to do more research. For ampouling I was thinking that I could just almost seal the ampoule and letting it cool before I put the liquid in,
similar to neutrino's procedure.
|
|
|
BromicAcid
International Hazard
Posts: 3253
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Ummm... Bp of hydrogen iodide is actually -35 C. Why would you want to ampule SO3 anyways?
|
|
|
Scratch-
Hazard to Self
Posts: 60
Registered: 22-2-2005
Location: U.S.
Member Is Offline
Mood: No Mood
|
|
Not sure, I hear its a pretty canary yellow as a liquid. I actually had trouble with the hydrogen iodide, there were several conflicting sites.
Dangerous and corrosive liquid gasses just seem to appeal to me, for no apparent reason. I'll have to devise an effective storage method for
these so they get neutralized if they ever get out (Out of some kind of inner container that is). Perhaps an inner sealed ampoule cushioned in a
larger outer container partially filled with a hydroxide for the more acid forming gasses.
|
|
|
a_bab
Hazard to Others
Posts: 458
Registered: 15-9-2002
Member Is Offline
Mood: Angry !!!!!111111...2?!
|
|
You don't seem to know enough chemistry yet. There is a thing involved here, which is called the "critical temperature". As
12AX7 stated, above this temperature, no matter how great the pressure is, the gas cannot be liquified anymore. Such gases are
hydrogen, oxygen and nitrogen to name a few. They all have critical temps lower than 30 degrees C. In an oxygen tank, the contents are gaseous even at
300 atm. Knowing that, you first have to filter your gases using this criteria, as the ampoule, even if made of steel will explode once you pass the
critical temperature, and then look for low pressure liquification gases.
There are two ways to liquify a gas: by the means of pressure or temperature.
Once you ampouled liquid nitrogen or helium let's say (which I doubt you'll ever see, as it's the melting temperature is almost 0
Kelvin), it doesn't mean that your stupid ampoule will witstand the thremendous pressure caused by the expansion of the boiling gas.
Study a little bit the law of the gases, so you can understand some basic notions, and then do your research concerning values like boiling/melting
point for gases.
A good starting point might be here
[Edited on 11-3-2005 by a_bab]
|
|
|
Scratch-
Hazard to Self
Posts: 60
Registered: 22-2-2005
Location: U.S.
Member Is Offline
Mood: No Mood
|
|
And you dont seem to be a good judge of chemistry knowledge. Yes I know what critical temperature is, thats what my research is about.
Perhaps I should rephrase the question in my second post to:
"Yeah the lower temperature ones, but in general arent most of the ones with a BP above the dry ice/acetone mixture also have a critical
temperature high enough to liquify?"
When I said it would be neat to ampoule liquid He I was joaking.
|
|
|
mick
Hazard to Others
Posts: 338
Registered: 3-10-2003
Member Is Offline
Mood: No Mood
|
|
If you ever want to open an old ampoule the best thing seems to be freeze it solid, dri-ice or liquid N2. Otherwise use gloves, goggles and a shield
because the thing might go bang. Stuff in ampoules can discolour which could mean some thing is happening in there.
mick
|
|
|
a_bab
Hazard to Others
Posts: 458
Registered: 15-9-2002
Member Is Offline
Mood: Angry !!!!!111111...2?!
|
|
Alright, sorry for the flame. I am always very rough. My mood is kinda angry usually.
Just gor your info, I am also very keen about liquid gases. An I posees 9 ampoules with SO3. (they are used as fumigant, you know, for making clouds
of H2SO4 smoke)
Still, the bromine is a liquid at room temperature.
|
|
|
BromicAcid
International Hazard
Posts: 3253
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Bromine may be a liquid at STP but we all know how readily it furmes so usually at my school we use ampules of it with 2.5 ml each. Storing under
water or H2SO4 also works but having ampules around is just convient.
|
|
|
cyclonite4
Hazard to Others
Posts: 480
Registered: 16-11-2004
Location: is unknown
Member Is Offline
Mood: Amphoteric
|
|
SO3 may not even need to be pressurised.
It has 3 crystalline modifications with melting points of 17, 33, and 67 degrees.
\"It is dangerous to be right, when your government is wrong.\" - Voltaire
|
|
|
BromicAcid
International Hazard
Posts: 3253
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Not to mention that without a polyermisation inhibitor your SO3 will really be reluctant to volatize in the near future.
|
|
|
a_bab
Hazard to Others
Posts: 458
Registered: 15-9-2002
Member Is Offline
Mood: Angry !!!!!111111...2?!
|
|
He started the thread with "I have a list of gasses here that might be neat to ampoule while liquid", and bromine (a liquid) is the first
one in the list.
|
|
|
Scratch-
Hazard to Self
Posts: 60
Registered: 22-2-2005
Location: U.S.
Member Is Offline
Mood: No Mood
|
|
Bromine probably wouldnt be liquid very long where I live . I just want to
collect liquid gasses because I think they would be neat, not for reagents. Can you describe your liquid SO3 a_bab? Can you also describe these
crystals cyclonite4?
|
|
|
a_bab
Hazard to Others
Posts: 458
Registered: 15-9-2002
Member Is Offline
Mood: Angry !!!!!111111...2?!
|
|
My SO3 is not liquid but a solid absorbed into some sort of earth thing. You can have liquid SO2 in an ampoule since it's easy to liquify.
[Edited on 12-3-2005 by a_bab]
|
|
|
Scratch-
Hazard to Self
Posts: 60
Registered: 22-2-2005
Location: U.S.
Member Is Offline
Mood: No Mood
|
|
Good idea, SO2 would be good for getting experience with liquid gasses. I'm still trying to find someplace to get ampoules, but I guess I could
just use large diameter glass tubing.
|
|
|
neutrino
International Hazard
Posts: 1583
Registered: 20-8-2004
Location: USA
Member Is Offline
Mood: oscillating
|
|
If you want experience, I suggest you start out with bromine (this teaches you the basics, especially not letting the liquid heat up) and the gas in
compressed air dusters (mine is HF<sub>2</sub>C-CH<sub>3</sub>, but the composition varies).
[Edited on 13-3-2005 by neutrino]
|
|
|
cyclonite4
Hazard to Others
Posts: 480
Registered: 16-11-2004
Location: is unknown
Member Is Offline
Mood: Amphoteric
|
|
I'm not saying they are crystals, Scratch.
What I'm saying is SO3 has three different cyrstaline modifications (alpha, beta and gamma, with melting points of 62, 33, and 17 degrees
celcius).
I've heard that SO3 is supposed to be a fuming solid or liquid, so having alpha or beta SO3 is most likely.
EDIT: Just to help you understand, here is a definition of crystallinity: The degree to which polymer molecules are oriented into
repeating patterns.
[Edited on 13-3-2005 by cyclonite4]
\"It is dangerous to be right, when your government is wrong.\" - Voltaire
|
|
|
Scratch-
Hazard to Self
Posts: 60
Registered: 22-2-2005
Location: U.S.
Member Is Offline
Mood: No Mood
|
|
Oh, I was thinking of a different definition of crystaline:
"Solid material composed of regularly repeating atoms, ions, or molecules that form defined patterns or lattice structures."
Is this correct? That makes me think its crystals. I see what you mean though.
Bromine might be a good gas to start with but I cant seem to find any NaBr to make it from, the local stores dont seem to carry it and I dont think
theres a pool supply store nearby. I'll try the compressed air, I have some of that. Thanks.
|
|
|
cyclonite4
Hazard to Others
Posts: 480
Registered: 16-11-2004
Location: is unknown
Member Is Offline
Mood: Amphoteric
|
|
I can understand what you mean. I find it a bit confusing too. Basically, it helps to think of a crystal as a polymer.
Your definition of crystal, I beleive, is quite correct. I was defining crystallinity.
Good luck anyways. 
\"It is dangerous to be right, when your government is wrong.\" - Voltaire
|
|
|
sparkgap
International Hazard
Posts: 1234
Registered: 16-1-2005
Location: not where you think
Member Is Offline
Mood: chaotropic
|
|
Both your definitions are consistent, cyclonite4 and Scratch-. The key word is "ordered". As long as whatever is comprising the substance in
question is in a regular (or fairly) pattern, it is a crystal.
And BTW, crystals can be liquid, too. You may want to take a look at your digital
displays the next time.
sparky (^_^)
"What's UTFSE? I keep hearing about it, but I can't be arsed to search for the answer..."
|
|
|
patu
Harmless
Posts: 9
Registered: 9-4-2004
Member Is Offline
Mood: No Mood
|
|
I managed to ampoule a small amount of liquid chlorine in a durham tube. The tube is only 50 mm long and 6 mm wide so it was tricky. I started off by
filling a 250 ml volumetric flask with chlorine gas from a hcl kmno4 reaction. I then cut a square piece of duct tape and poked a hole with a nail in
the middle. I then pushed the durham tube through it having the sticky side of the tabe on the same side as the open end of the tube. I then put the
tape with the tube sticking out on top of the flask with the chlorine. i then inverted the whole unit and inserted only the tube part into a cut off
coke can filled with dry ice. i used a ring stand and clamps to hold up the flask. after about five minutes i lifted up the whole thing and saw a
small amount of yellow liquid at the bottom of the durham tube. i immediately put the tube back under the dry ice. i removed the flask and the tape
and left the tube in the dry ice. the tube was sticking out enough for me to torch it shut. the first two i did had small holes that didnt close so
all of the liquid chlorine leaked out within five minutes of it warming up. the last one fully closed because i still have liquid chlorine in it and
it has been a day. Me happy!!!!
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
