Pages:
1
2 |
kclo4
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline
Mood: No Mood
|
|
destroying chlorates and leaving the prechlorates
I have read many essays on how to destroy the chlorates and not the prechlorates unfortunately most had a great lack of the procedure and the one that
gives a procedure was too dangerous and costly. Certainly there is other ways.
If any one knows of a synthesis or a site pleas post
Thank you
|
|
guy
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
Do you just want to seperate the two? If it were NaClO3 and NaClO4, according to this msds, you can have a solution of 209% NaClO4 in water, and NaClO3 only dissolves 100g in 100ml of water, so you can evevaporate the water to
isolate one of them.
|
|
kclo4
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline
Mood: No Mood
|
|
That would work but I do not know how much naclo3 is in my solution
|
|
BromicAcid
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3237
Registered: 13-7-2003
Location: Wisconsin
Member Is Offline
Mood: Rock n' Roll
|
|
Destroying Chlorate by Chemical Means a 10 minute google find.
|
|
kclo4
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline
Mood: No Mood
|
|
Switching to google
|
|
hodges
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 525
Registered: 17-12-2003
Location: Midwest
Member Is Offline
|
|
You could heat the chlorate to give perchlorate and chloride and then re-crystalize since the chloride is much more soluable than the perchlorate.
|
|
guy
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
Quote: |
since the chloride is much more soluable than the perchlorate.
|
That would only work for the potassium salt. The sodium perchlorate is highly soluble.
|
|
MadHatter
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1333
Registered: 9-7-2004
Location: Maine
Member Is Offline
Mood: Enjoying retirement
|
|
Solubilities
From CRC 62<sup>ND</sup> Edition(1981-1982) in grams per 100 ml H<sub>2</sub>O:
KCl_______23.80 @ 20C____56.70 @ 100C
KClO<sub>3</sub>______7.10 @ 20C____57.00 @ 100C
KClO<sub>4</sub>_______.75 @ 0C_____21.80 @ 100C
NaCl______35.70 @ 0C_____39.12 @ 100C
NaClO<sub>3</sub>____79.00 @ 0C____230.00 @ 100C
NaClO<sub>4</sub>___209.00 @ 15C___284.00 @ 50C
The NaClO<sub>4</sub> is the monohydrate: NaClO<sub>4</sub>.H<sub>2</sub>O
From opening of NCIS New Orleans - It goes a BOOM ! BOOM ! BOOM ! MUHAHAHAHAHAHAHA !
|
|
kclo4
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 916
Registered: 11-12-2004
Location:
Member Is Offline
Mood: No Mood
|
|
I research and I thick I am going to destroy the chlorates with Sodium metabisulphite
The reaction that happens is
3Na2S2O5 + H2O + 2NaClO3 => 3Na2SO4 + 3H2SO4 + 2NaCl
Than I am going to and naoh to neutralize the acid
But I till don’t know how to get the pure naclo4 with out the other contaminations
Is any one knows a way or another reaction that creates a insoluble salt
And how can I make NaS2O5 or the acid. Could I just add h2o2 to H2SO4 I read that’s how you can make it but I don’t see how
|
|
guy
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 982
Registered: 14-4-2004
Location: California, USA
Member Is Offline
Mood: Catalytic!
|
|
You could fractionally crystallize all of them since NaClO4 will stay in the solution. (209%)
|
|
garage chemist
chemical wizard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1803
Registered: 16-8-2004
Location: Germany
Member Is Offline
Mood: No Mood
|
|
You could add KCl solution, this would precipitate KClO4, which is highly insoluble in cold water.
KClO3 is also sparingly soluble in cold water, but not nearly as insoluble as KClO4. You should work in a highly diluted solution to keep the KClO3
from precipitating!
[Edited on 2-1-2005 by garage chemist]
|
|
chemoleo
Biochemicus Energeticus
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3005
Registered: 23-7-2003
Location: England Germany
Member Is Offline
Mood: crystalline
|
|
I think the idea is to first destroy the chlorate by chemical means, and then to extract the perchlorate by precipiation with a potassium salt.
The resulting KClO4 precipitates and is free of KClO3, if the chemical destruction of the chlorate was complete. I suggest to take stoichiometric
quantities of bisulphite vs the amount of NaCl you started off with, just to make sure you aren't left with KClO3 - particularly if you obtained
your solution of sodium (per) chlorate by electrolysis or heating of chlorate.
Hodges - did you try the heating method to disproportionate the chlorate to perchlorate and chloride? From what I read this requires to keep the temp
of the chlorate/perchlorate mix at the MP for several hours. If too high, the chlorate/perchlorate decomposes, if too low it solidfies, or the
reaction is slow.
It's more of a hassle than it looks. I'd also prefer chemical means, although I wouldnt be happy about the contamination with other salts.
Never Stop to Begin, and Never Begin to Stop...
Tolerance is good. But not with the intolerant! (Wilhelm Busch)
|
|
neutrino
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1583
Registered: 20-8-2004
Location: USA
Member Is Offline
Mood: oscillating
|
|
Quote: | Originally posted by kclo4
And how can I make NaS2O5 or the acid. Could I just add h2o2 to H2SO4 I read that’s how you can make it but I don’t see how
|
This creates the peroxysulfate (SO<sub>5</sub>-) ion, not the one you’re after.
|
|
budullewraagh
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 168
Registered: 1-8-2004
Location: new york
Member Is Offline
Mood: Aliphatic
|
|
[nitpick]peroxysulfate is a -2 anion[/nitpick]
|
|
hashashan
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 255
Registered: 10-10-2006
Member Is Offline
Mood: No Mood
|
|
Say guys, i have a problem. NaS2O5 is quite expensive in my country and i dont want to use tons of it.
So i thought that ill use small quantities till there is no chlorate left. But another problem is that i dont have any indicators. what is the best
way to make an indictor or another method of safely destryoing the chlorate so i can make ammonium perchlorate?
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
Acidify the liquid a little bit and make it warm (60 C or so) and add the Na2S2O5 in small steps. As soon as a clear smell of SO2 can be observed, you
have converted all chlorate. This test is quite sensitive, the smell of SO2 is strong and pungent, and even an excess of a single spatula of Na2S2O5
will cause a very strong and pungent smell.
|
|
hashashan
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 255
Registered: 10-10-2006
Member Is Offline
Mood: No Mood
|
|
ok, but what if the SO2 shuts down my smell sense? i once had this, almost killed myself with a reaction ( or was it H2S?)
and how good is this method? would you dare to make AP with this perch?
|
|
12AX7
Post Harlot
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
You could also use a dash of Fe(III) sulfate. Chlorate should be reduced in favor of Fe(III) until all chlorate is gone.
Obviously, you don't put in so much Na2S2O5 that it gasses you. If it's so strong that you can't smell the shit anymore, chances are you're
done............
Tim
[Edited on 5-16-2007 by 12AX7]
|
|
hashashan
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 255
Registered: 10-10-2006
Member Is Offline
Mood: No Mood
|
|
Hi,
i saw on the geocities site a method for cheching for chlorates that uses MnSO4 and phosphoric acid. Anyone tried it, or care to explain in a fully
detailed manner how to preform this test, because for some reason it doesnt work for me.
Manganous Sulphate-Phosphoric Acid
Manganous Sulphate in syrupy (concentrated) Phosphoric acid solution reacts with Chlorates to form the violet coloured Mangani-Phosphate ion:
6Mn++ + 12PO4- - - + 6H+ + ClO3 - === 6[Mn(PO4)2]- - - + Cl - + 3H2O
Persulphates, nitrates, bromates, iodates and aslo periodates react similarly.
A drop of the test solution is put into a micro crucible and a drop of the reagent is added. Warm rapidly over a micro burner and allow to cool. A
violet coloration appears. Very pale colorations may be intensified by adding a drop of 1% alcoholic diphenylcarbazide solution when a deep violet
colour, dur to an oxidation product of the diphenylcarbaxide, is obtained.
Sensitivity: 0.05 ug (micro grams). ClO -.
Concentration: 1 in 1,000,000.
The reagent is made up by adding equal volumes of concentrated phosphoric acid and saturated manganese (II) sulphate solution.
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
If you have the chems, then you could use that method. It is based on formation of a manganese (III) complex, which is deep purple.
If you don't have the chems, simply use the method with the SO2 smell. If you use just a small spatula at a time, then believe me, you won't gas
yourself. SO2 is pungent, and you definitely notice the smell. It is H2S, which kills your sense of smell, not SO2.
So, if you think you smell SO2 remains and do not really trust, then simply add one other small spatula of Na2S2O5 if that makes you feel more
comfortable. Simple, effective and only requires a spatula or 2 excess of Na2S2O5.
[Edited on 17-5-07 by woelen]
|
|
hashashan
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 255
Registered: 10-10-2006
Member Is Offline
Mood: No Mood
|
|
ok well, probed some of my batch, gassed myself with SO2 . i just don't smell
this thing, just started to hurt in my nose and then in the lungs.
I do have all the chems for the test, but for some reason it doesn't work.
how much of the sulfate should i add to the acid? if i add in in stoichiometry it just gets really really gooey.
anyone?
|
|
woelen
Super Administrator
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 7990
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
If the SO2 burns in your lungs, then you really don't have to worry about remains of chlorate .
I did the other test with some chlorate, and it works nicely. Simply add a tiny pinch of solid MnSO4 to 2 ml of phosphoric acid (85%). Then I added
some chlorate and heated all of this, until the water was boiling away. The color quickly changes from colorless to a beautiful purple, quite close to
the color of a not too concentrated solution of KMnO4.
The use of a 1 : 1 mix of concentrated H3PO4 and conc. MnSO4 solution does not seem very good to me. The only thing you get in that case is a lot of
black crap. The complex is very dark and even tiny amounts already have a deep purple color.
|
|
G.i.B.
Harmless
Posts: 22
Registered: 17-5-2007
Location: amsterdam
Member Is Offline
Mood: confused but happy
|
|
I just tried the MnSO4-H3PO4 (85%) (add solid to syrurpy liquid) method, and it works just fine. Even with a tiny amount of chlorate I got a nice
purple colour. I forgot to heat the first time, ahum... Make sure it boils a little !!
|
|
hashashan
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 255
Registered: 10-10-2006
Member Is Offline
Mood: No Mood
|
|
The problem is that my MnSO4 is already a little bit purple(but really a bit).
now you say you take 2ml of phosporic and add there really a small amount of MnSO4(i mean like at the tip of the knife? or some more?) and then you
add couple of drops of your solution and then you boil it down? because i did tget the colorless liquid... can you please be more specific because i
do have some problems with this methos
thanks
|
|
G.i.B.
Harmless
Posts: 22
Registered: 17-5-2007
Location: amsterdam
Member Is Offline
Mood: confused but happy
|
|
I think MnSO4 should be a little purple (mine is anyway) Take 2 ml H3PO4 (85%) add a little MnSO4 (I tried a tiny bit up to a good knife tip full, it
all worked) Add 0.5 ml chlorate solution, and then heat to a boil. If this doesnt work for you, I think you should check your chems.
[Edited on 17-5-2007 by G.i.B.]
|
|
Pages:
1
2 |