Artemus Gordon
Hazard to Others
Posts: 178
Registered: 1-8-2013
Member Is Offline
Mood: No Mood
|
|
Any comments on buying pH meters?
I did try to UTFSE and found nothing about this topic, which surprises me. pH meters are available in a very wide range of prices. Anybody have
good/bad experiences with certain features, models, or brands?
I assume long, thin electrodes are better than the short kind, but maybe they have reliability or accuracy issues?
|
|
|
PeeWee2000
Hazard to Self
Posts: 58
Registered: 2-7-2013
Location: Michigan
Member Is Offline
Mood: No Mood
|
|
pH meters are tricky, you need to maintain them after every use make sure you get everything you need to do this. Basically when looking for one you
get what you pay for, if you buy a 10$ aquarium pH meter from china thats what you get if you get a 100$ pH meter from europe it'll work much better.
http://www.ebay.com/itm/Milwaukee-MW102-Smart-pH-C-Meter-SM1... Heres the one I have it works without problem and automatically adjusts for
temperature and is very easy to calibrate plus it has replacable probes. The seller sells everything you would need for it, new probes, cleaning
solution, storage soluton and calibration solution. Although you can probably make the storage solution and cleaning solution fairly cheaply and
easily instead of buying the overpriced ones. I wouldnt skimp out on calibration solutions though, the link I posted comes with 2 calibration packets
for one time use.
“Everything is relative in this world, where change alone endures.”
― Leon Trotsky
|
|
|
Artemus Gordon
Hazard to Others
Posts: 178
Registered: 1-8-2013
Member Is Offline
Mood: No Mood
|
|
Thanks, PeeWee.
What about long-term storage? Is there a risk of the storage soln evaporating away, and if so, does this hurt the electrode?
|
|
|
Chemosynthesis
International Hazard
Posts: 1071
Registered: 26-9-2013
Member Is Offline
Mood: No Mood
|
|
I'm actually really interested in any advice people have as well. I've only used high end (Corning, Milwaukee Instruments, etc.) tabletop meters for
buffer formulation, and never paid too much attention to specifics as they are all easily >$300 at minimum, and not a large part of what anyone
does around there. As long as you screw on the little solutions and ensure washing between contact, I have not seen any solution evaporate
appreciably when capped.
Never seen this, but I don't think any damage results from allowing the glass/electrodes to dry either (though everyone taught me never to do this),
though it would be really annoying to re-hydrate before use, then re-calibrate.
|
|
|
Artemus Gordon
Hazard to Others
Posts: 178
Registered: 1-8-2013
Member Is Offline
Mood: No Mood
|
|
How long would rehydration take? An hour? A day?
If it was an hour, that wouldn't bug me because I tend to do my experiments in bursts with sometimes weeks of inaction in between.
|
|
|
Chemosynthesis
International Hazard
Posts: 1071
Registered: 26-9-2013
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Artemus Gordon  | How long would rehydration take? An hour? A day?
If it was an hour, that wouldn't bug me because I tend to do my experiments in bursts with sometimes weeks of inaction in between.
|
I'm not sure. Sorry. It would be an interesting experiment to see. I'll bet emailing a manufacturer would be fruitful.
|
|
|
Artemus Gordon
Hazard to Others
Posts: 178
Registered: 1-8-2013
Member Is Offline
Mood: No Mood
|
|
OK, I found this on eutechinst.com -
"After removing the electrode from soaking bottle or protective cap at the bottom of sensor, place the electrode in a clean container containing one
of the liquids i.e. 4.0 M KCl or pH 7.0 buffer. Soak electrode for 30 minutes if left dry."
But, it also says -
"The sensor should never be stored dry. Always keep pH electrode moist. Proper pH electrode storage maximizes electrode performance and extends
electrode life."
This is for glass electrodes, IDK if the same applies to junction electrodes.
|
|
|
numos
Hazard to Others
Posts: 269
Registered: 22-2-2014
Location: Pasadena
Member Is Offline
Mood: No Mood
|
|
Personally I like ph paper much more, unless you need lab grade accuracy,which in that case the lab should have a good one, ph paper works fine, quick
easy,and no maintenance. The meters are cumbersome and personally for home use, I'd take paper over meter any day...
|
|
|
Dr.Bob
International Hazard
Posts: 2753
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: Mildly disgruntled scientist
|
|
I have to agree on pH paper, it ismuch simpler. Unless you are doing titrations and complex analytical work, 0-14 pH papers will work for most
functions. But otherwise buy a mid-line ones.
|
|
|
PiledhigherandDeeper
Harmless
Posts: 17
Registered: 17-3-2013
Location: USA
Member Is Offline
Mood: No Mood
|
|
pH meters in the teaching lab have given me fits... very finicky, with error warnings that take way too long to diagnose.
I can't speak for the accuracy, but for ease of measurements and since I am mostly interested in demonstrating the big picture concepts (pH titration
curve analysis, change of temperature with time curves), I dig the Vernier hardware. Lots of options for other probes once you get an interface,
pretty much plug and play, bulletproof...
http://www.vernier.com/products/interfaces/
I have a colleague that uses the Labquest interface, in intro level chem labs, as well as P-chem. CBL's are my go to.
Just my $.02.
I'll third, fourth, what has been said though... can't beat pH paper for most apps.
[Edited on 5-4-2014 by PiledhigherandDeeper]
|
|
|
GoldGuy
Harmless
Posts: 45
Registered: 24-11-2013
Location: Toronto, ON
Member Is Offline
Mood: Not sure if awake or in a dream where Im trying to fully awake.
|
|
I bought a pH meter for 15 dollars. Guy happened to live 3 minute walk from my house! It works beautifully and I calibrated it with a can of Sprite
(pH 3.8) and borax solution (pH 9.1).
So my advice is low price does not equal low quality
http://toronto.kijiji.ca/c-buy-and-sell-other-BRAND-NEW-DIGI...
[Edited on 6-4-2014 by GoldGuy]
|
|
|
DrAldehyde
Hazard to Self
Posts: 82
Registered: 12-1-2014
Member Is Offline
Mood: No Mood
|
|
I concur with meters being finicky. We use handheld meters for water test at three sites. Consistency is much more important than accuracy for us. We
buy meters in the $100-$200US range. We use fresh calibration solutions, storage solutions, and cleaning solutions. What I find is I can calibrate
all six meters at the same time and end up getting six readings covering a 1.0pH range. These are meters with purported accuracy to the 100ths. I
don't know how they can even sell this garbage. I find if I calibrate several times, I start getting more stable readings. I end up using two meters
for every test to average the results.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
