M4D1NV3N70R
Harmless
Posts: 6
Registered: 28-11-2004
Member Is Offline
Mood: Muah-ha-ha-ha!!
|
|
Liquid With A Very High Expansion When Heated?
Hello,
I'm looking for a liquid that expands/vaporizes a great deal when a modest amount of heat is applied to it. I'm not looking for any kind of
combustion, just expansion and/or phase change.
The idea is to generate as much pressure as possible for a given amount of heating.
Would a modern refridgerant such as freon or that R-12 stuff be what I'm looking for?
Thanks!
[Edited on 28-11-2004 by M4D1NV3N70R]
Change is good. Especially when it\'s more than you just paid.
|
|
vulture
Forum Gatekeeper
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
Refrigerants are selected for their heat capacity and evaporation enthalpy, not expansion, so it's doubtful you'll have any luck there.
I don't know if the CRC handbook lists expansion coefficients...
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
mick
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 338
Registered: 3-10-2003
Member Is Offline
Mood: No Mood
|
|
you could be talking of water and steam under the right pressure and temperature. If you can find the critical temperature and pressure of the liquid
you are thinking about you could get more power than steam gives. I think they were called phase diagrams. Find the bit where the liquid can not exist
as a liquid but as a gas and then use the ideal gas equation. It could give you a rough idea of how much expansion there could be. CO2 is easily
liquified and sublimed but I think there is a bit where it is always gas.
mick
[Edited on 30-11-2004 by mick]
|
|
M4D1NV3N70R
Harmless
Posts: 6
Registered: 28-11-2004
Member Is Offline
Mood: Muah-ha-ha-ha!!
|
|
Thanks! That helps a lot. I had no idea where to start to figure this out.
Change is good. Especially when it\'s more than you just paid.
|
|
HNO3
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 211
Registered: 10-11-2004
Location: America
Member Is Offline
Mood: No Mood
|
|
Umm, butane refiller bottles might work. But the name M4D1NV3N70R sounds a little bit KEI_!$I-I. Ummm, that is kewlish.
![:mad:](./images/smilies/mad.gif)
\"In the beginning, God...\" Wait a minute, God doesn\'t exist!!!!!!!!!! \"OK, in the beginning, ummm, hydrogen...\" Wait a minute, what about the
laws of thermodynamics? \"OK, in the beginning, ummm.....UMMMMM, what\'s left to choose from?
|
|
neutrino
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1583
Registered: 20-8-2004
Location: USA
Member Is Offline
Mood: oscillating
|
|
For a liquid, I might suggest mercury. If my lousy memory serves, it was listed in the Guinness Book some year as the liquid with the highest thermal
expansion coefficient. If you want something that will boil, remember that the pressure the boiling liquid will exert is equal to its vapor pressure
at that temperature. If you do want something like this, I would suggest gas dusters. They usually contain fluorinated hydrocarbons with boiling
points around -30*C and vapor pressures of 5-7 atm at room temperature.
|
|
S.C. Wack
bibliomaster
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
Dalton's law might come in handy here.
|
|
mick
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 338
Registered: 3-10-2003
Member Is Offline
Mood: No Mood
|
|
The only thing I can think of is ammonia. 18g of water could give you 22.14 l of gas at the right temperature. 17g of ammonia could give the same or
more. I think the heat of vapourisation comes into it. The only other thing I can think is boron trihydide, diborane, which could be explosive.
mick
|
|
Twospoons
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1314
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Ha! Try liquid Helium
|
|
MadHatter
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1333
Registered: 9-7-2004
Location: Maine
Member Is Offline
Mood: Enjoying retirement
|
|
He
Twospoons, I think you nailed it but M4D1NV3N70R might have a hard time getting it.
Probably needs something more available. Liquid nitrogen should be easier to acquire.
From opening of NCIS New Orleans - It goes a BOOM ! BOOM ! BOOM ! MUHAHAHAHAHAHAHA !
|
|
M4D1NV3N70R
Harmless
Posts: 6
Registered: 28-11-2004
Member Is Offline
Mood: Muah-ha-ha-ha!!
|
|
OK, lots of helpful info. Thanks.
But I am kind of looking to avoid cryogenic temperatures. And the materials required to work with them.
Change is good. Especially when it\'s more than you just paid.
|
|
S.C. Wack
bibliomaster
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
? There are no low temperatures involved, only tanks and an appropriate hose. Turn the tank upside down, liquid whatever comes out, goes through the
hose, into the other tank.
Well fuck, it looks like just about anything will give a high pressure. Why not a solid - CO2? Convenient even with cryogenic handling.
[Edited on 4-12-2004 by S.C. Wack]
|
|
Magpie
lab constructor
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
All liquids provide 22.4 liters of volume per gram mole at standard conditions when they form a gas if they behave ideally or close to it. So, from a
theoretical standpoint you are looking for a liquid with a low molar heat of vaporization. A table of compounds listing this should be available in
handbooks such as CRC or Perry's Chem. Engr. You probably want the boiling point to not be too high also.
[Edited on 4-12-2004 by Magpie]
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|