rocketscience
Harmless
Posts: 13
Registered: 21-11-2004
Member Is Offline
Mood: No Mood
|
|
Rocket propellant
I was wondering if any one knows if rocket propellant should have enough oxidizer to burn all the fuel or just most I am afraid if the oxidizer burns
all the fuel if it will burn way to quick and possibly explode
Edit: bad spelling in title.
[Edited on 23-11-2004 by chemoleo]
|
|
|
Geomancer
Hazard to Others
Posts: 228
Registered: 21-12-2003
Member Is Offline
Mood: No Mood
|
|
The burn rate of propellant must be experimentally determined. I can see no reason why you shouldn't be able to burn lean (oxgen rich)
propellants well. Nobody does it though, since rich mixtures provide better performance. There is a family of programs (ProPEP, etc.) that can predict
the performance aspects of a given propellant, but they cannot determine such things as burn rate and pressure exponent.
For your sake, I recommend you do quite a bit more research before actually experimenting. Sutton's book Rocket Propulsion Elements is
the standard, but there are others. Also check out Richard Nakka's site.
|
|
|
MadHatter
International Hazard
Posts: 1339
Registered: 9-7-2004
Location: Maine
Member Is Offline
Mood: Enjoying retirement
|
|
Rocket Candy
I've made rockets using the standard mix of potassium nitrate/sugar at a ratio of 65:35.
This is fuel rich but for whatever reason it gives the best performance. As for explosions, I
found that any type of airgap in the fuel is the culprit.
From opening of NCIS New Orleans - It goes a BOOM ! BOOM ! BOOM ! MUHAHAHAHAHAHAHA !
|
|
|
budullewraagh
Hazard to Others
Posts: 168
Registered: 1-8-2004
Location: new york
Member Is Offline
Mood: Aliphatic
|
|
i prefer potassium chlorate to nitrate when combined with sugar
|
|
|
JohnWW
International Hazard
Posts: 2849
Registered: 27-7-2004
Location: New Zealand
Member Is Offline
Mood: No Mood
|
|
Can Sutton's book Rocket Propulsion Elements be downloaded from any site?
|
|
|
Marvin
National Hazard
Posts: 995
Registered: 13-10-2002
Member Is Offline
Mood: No Mood
|
|
Potassium Chlorate fuels have safety problems. Its extremely unwise for someone just starting the hobby to use them.
To address the actual question, yes there must be enough oxidiser to burn all the fuel. Any unburned fuel or unused oxidiser constitutes dead weight.
The term 'burned' though gets very complicated. For example for carbon it usually better to consider carbon monoxide as 'burned'
as this usually results in a fuel having a higher energy density. It is true however to say anything coming out of the exhaust in the same form as
it was in the propelent is wasted.
|
|
|
neutrino
International Hazard
Posts: 1583
Registered: 20-8-2004
Location: USA
Member Is Offline
Mood: oscillating
|
|
Why would you want to use chlorates? They have less oxygen than perchlorates, are much less stable, and generally more expensive. If you really want a
good perchlorate, use ammonium perchlorate.
|
|
|
AngelEyes
Hazard to Others
Posts: 187
Registered: 24-1-2003
Location: South of England
Member Is Offline
Mood: Better than it used to be.
|
|
Because Chlorates are easier to get hold of that perchlorates and cheaper. It's also a better oxidiser than a nitrate. Sure, there are
incompatibility issues with Chlorates but if you're careful these can be dealt with. Just avoid sulphur (and sulphur compunds) at all times.
Not everyone lives in the US where you can simply mail order Perchlorates and fine Al powder form Skylighter - some of use have to look hard for our
chems and we will gladly use a bit of chlorate if necessary. It all comes down to common sense - if you're careful then you'd be unlucky to
get burned...but if you're a kewl chump then you deserve everything you get.
\'Silk and satin, leather and lace...black panties with an Angel\'s face\'
|
|
|
tokat
Hazard to Self
Posts: 64
Registered: 1-6-2004
Location: 6feet south
Member Is Offline
Mood: No Mood
|
|
"I was wondering if any one knows if rocket propellant should have enough oxidizer to burn all the fuel or just most I am afraid if the oxidizer
burns all the fuel if it will burn way to quick and possibly explode "
Make it so it in perfect balance, then add a binder,melted sugar, PVC,hell all most anything, then add a themite/redox Al-fe and use the amount of
themite to goveing the speed.
Eg AN + Al + Fe2O3(one that is highly oxy) + Binder.
The themite makes heat to break down the AN, more themite per square inch more amount/quicker the reaction
[Edited on 24-11-2004 by tokat]
|
|
|
redneck
Harmless
Posts: 12
Registered: 26-9-2004
Member Is Offline
Mood: No Mood
|
|
Hallo rocketscience
At high temperatures CO2 can't be formed under low pressure. CO ist formed instead. That's the reason why rocketfuels are balanced to
produce CO.
Don't use chlorates as oxidiser because they are so sensitive that there is a great risk that the rocket will detonate instead of lift up.
Nitrates are a better oxidiser for rocket fuels because they produce more gas and more energy. They burn slower thus they are saver.
Take 60% finely powdered potassium nitate and 40% powdered sugar (2% rust can be added to get a slightly higher burn rate). Give both substances in a
cup and add enough lighter petrol to make a mush. Stir for 5 min and then insert the mush in your rocket. Let it dry for two days. This procedure
gives a high density rocket fuel and so reduces the risk of an explosion.
To make a rocket with this medium fast burning fuel you need a small nozzle. For example if the internal diameter of your rocket is 16 mm then the
diameter of your nozzle must be smaller than 3 mm if your rocket consists of a metall pipe. If its made out of a paper roll the nozzle must be wider
because paper can't withstand as much pressure as metall.
The smaller the nozzle is the wider, higher and faster the rocket will fly. But if it's too small the rocket will explode. If it's too wide
the rocket will just smoke instead of fly.
If you bild a rocket without fins you can inset it in a long pipe (round about 1.5 times as wide as your rocket) to start it.
Use a fuse that gives you enough time to get far away and behind cover when you try to start a selfmade rocket because it could explode. They are
potentialy as lethal as pipeboms. Never stand next to it when it starts.
|
|
|
Harpoon
Harmless
Posts: 5
Registered: 19-11-2004
Member Is Offline
Mood: Pyrophoric...
|
|
The only times I've seen rockets explode was when the propellant was compressed insufficiently, or the casing was too weak and the nozzle too
small.
A weak casing will rupture, and loose propellant will burn faster as it has a greater surface area, leading to higher pressures and therefore ruptured
casings.
As for chlorates, I've had good success (so far) in compressing a sodium chlorate/paper mix in a vice e.g. no unwanted ignitions.
The only time I could get this mixture to ignite was when I deliberately hammered a sample several times.
I like the idea of launching rockets from a pipe. Perhaps if one end of the pipe was sealed/restricted, the pipe buried, and the rocket dropped in
like a (military) mortar shell...
Flick out fins could enhance the flight path of the rocket.
|
|
|
rocketscience
Harmless
Posts: 13
Registered: 21-11-2004
Member Is Offline
Mood: No Mood
|
|
I personally don’t think that nitrates are worth a darn or at least kno3 because from some research I have done on it. It reluctantly release oxygen
and know or potassium nitrite dose not decompose when heated and kno3 is pretty expensive butt also naoclo2 or sodium chlorate dose the same so for
rocket propellants prechlorate would be the best and can easily be made from salt
|
|
|
Ramiel
Vicious like a ferret
Posts: 484
Registered: 19-8-2002
Location: Room at the Back, Australia
Member Is Offline
Mood: Semi-demented
|
|
RS: I've had some success with rich KNO<sub>3</sub> + Sugar mixes. Usually consistent and fine admixture is needed. Remember that
reaction rates increase with pressure, so sometimes the ill-advised method of having the nozzle a tad too small is necessary to build up pressure
(think of it as a paradoxical “semi-closed” system [I know! Its either closed or it fuggin aint, but tell that to any good professor] ).
This topic is very practical... I should hate to think what would happen if a mod were to see it.
And now to demonstrate my hypocrisy:
Harpoon, how would you create the flick out fins? Because I've tried for about 6 months without fining a solution - short of actual metal hinging
(from the rear – which requires considerable machining prowess!) or spring coil (from the sides). I can recommend the tube method though, it's
quite something!
Caveat Orator
|
|
|
tokat
Hazard to Self
Posts: 64
Registered: 1-6-2004
Location: 6feet south
Member Is Offline
Mood: No Mood
|
|
"I personally don’t think that nitrates are worth a darn or at least kno3 because from some research I have done on it. It reluctantly
release oxygen and know or potassium nitrite dose not decompose when heated and kno3 is pretty expensive butt also naoclo2 or sodium chlorate dose the
same so for rocket propellants prechlorate would be the best and can easily be made from salt"'
i see were you coming from, i got my KNO3 from a farm sullpie, it was about $2 per KG, But allmost inposalbe to find.If you mix chacoal and sulpher it
is hard to lit with a cig liter so use steel wool fumlments. Personly i don't like useing KNO3 becuase with sugar the limit between zero thrust
and exploeding is small. I don't know weather you know about rockets but this is what i think.
Make the powder compressed so you can control suface area, i will check my notes and edit, but mild steel i think as 220psi per square inch, and was
thinking but having a throat of say(9mmID,11OD,3mm throat for a lossly packet KNO3+sugar is about right(test),adding water to cake.
|
|
|
MadHatter
International Hazard
Posts: 1339
Registered: 9-7-2004
Location: Maine
Member Is Offline
Mood: Enjoying retirement
|
|
Melting
I mix my KNO3 and sucrose in water. Then I boil it down and carefully allow it to melt.
This way I can pour it molten into the rocket motor body. Mixing in water in advance makes
a more intimate mix before melting. It doesn't cool off to completely solid but more a rubbery
consistency.
From opening of NCIS New Orleans - It goes a BOOM ! BOOM ! BOOM ! MUHAHAHAHAHAHAHA !
|
|
|
Harpoon
Harmless
Posts: 5
Registered: 19-11-2004
Member Is Offline
Mood: Pyrophoric...
|
|
Ramiel, I'd build the fins out of thin springy plastic, and roll them around the body of the rocket prior to loading them into the tube.
You'll need to score the fins very lightly to provide a fold line where they attach to the rocket.
|
|
|
rocketscience
Harmless
Posts: 13
Registered: 21-11-2004
Member Is Offline
Mood: No Mood
|
|
I don’t think I am going to put the rockets in a pipe I plan to do ones similar to the ones in October sky but with a recovery system and a lot
smaller does any one have a suggestion for a ejection charge and a good binder (I need to know the chemical formula for the binder)
|
|
|
axehandle
Free Radical
Posts: 1065
Registered: 30-12-2003
Location: Sweden
Member Is Offline
Mood: horny
|
|
| Quote: |
...suggestion for a ejection charge and a good binder (I need to know the chemical formula for the binder)
|
You don't want a binder in the ejection charge mix -- a binder would inhibit burning and the whole point of the ejection charge is that it should
go "POF!" very very quickly, ejecting whatever it's designed to eject explosively. I'd suggest "Crimson Powder": http://www.nakka-rocketry.net/articles/Crimson_powder.pdf
It's a mix of ascorbic acid, KNO3 and Fe2O3 that is imtimately mixed by crystallization from an aqueous solution -- no grinding necessary.
I've made it myself once for testing it, albeit sans the Fe2O3. It packs quite a whollop.
PS. The easiest to prepare and cast rocket fuel I've ever used was a 64/34/2 mixture of KNO3, sorbitol and Fe2O3. Lovely stuff, it can be
intimately mixed by dissolving in water, then the water evaporated slowly and the sorbitol melted. Casts easily and doesn't caramellize if
accidentally overheated. Only difficulty is finding sorbitol.
I've also used 64/34/2 KNO3/glucose/Fe2O3, all ingredients gently ball milled for 4 hours prior to melting. Doesn't caramellize as easy as
sucrose based fuel but still worse than the sorbitol based fuel.
You'll want to build a dedicated melting pot from a deep-frier, BTW. Melting sugar/KNO3 based fuels on hotplate or flame is suicidal and a
deep-frier already comes equipped with a thermostat ideally suited for the melting range of the sugar/sorbitol based fuels (100..120 degrees C or
so-so). Continuous stirring is required though.
|
|
|
rocketscience
Harmless
Posts: 13
Registered: 21-11-2004
Member Is Offline
Mood: No Mood
|
|
I think I am going to use ammonium prechlorate, aluminum, iron oxide, and carbon for the propellant. But I need a good binder that is cheap, simple,
and I need to know is chemical formula.
|
|
|
axehandle
Free Radical
Posts: 1065
Registered: 30-12-2003
Location: Sweden
Member Is Offline
Mood: horny
|
|
Binder.
This has degenerated into a practical discussion of pyrotechnics -- which is against the forum rules. I suspect the thread will be detritized very
soon.
Still, I'll give you a couple of ideas for binders:
1) Parlon. Binder and fuel. Soluble in ethyl acetate.
2) PVC. Binder and fuel. Soluble in THF.
3) This is my own untested idea: PMMA (plexiglass). Binder and fuel. Soluble in acetone.
4) Asphalt + oil. Binder and fuel.
I'll bet you could find heaps more by a simple google search.
PS. IMHO, composite fuels using chlorates/perchlorates are unsuited for a beginner. I'd go with KNO3 based fuels. But it's your show.
[Edited on 2004-11-26 by axehandle]
My PGP key, Fingerprint 5D96 E09E 365D 1867 2DF5 C2FE 4269 9C19 E079 CD35
\"Verbing nouns weirds the language!\"
|
|
|
vulture
Forum Gatekeeper
Posts: 3330
Registered: 25-5-2002
Location: France
Member Is Offline
Mood: No Mood
|
|
CAUTION
| Quote: |
I personally don’t think that nitrates are worth a darn or at least kno3 because from some research I have done on it. It reluctantly release oxygen
and know or potassium nitrite dose not decompose when heated and kno3 is pretty expensive butt also naoclo2 or sodium chlorate dose the same so for
rocket propellants prechlorate would be the best and can easily be made from salt
|
Get your chemistry straight first! You obviously have no clue what you're talking about!
Because of your obvious lack of knowlegde and willingness to put effort into this, I not only see you as a potential hazard to yourself and others,
but I will also close this thread.
[Edited on 26-11-2004 by vulture]
One shouldn't accept or resort to the mutilation of science to appease the mentally impaired.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
