golfpro
Banned
Posts: 179
Registered: 18-5-2013
Member Is Offline
Mood: Cap Sensitive
|
|
Detonators and some other questions.
Hi,
So this summer I will be going up to a cabin almost every weekend and access to remote area where i want to do some detonations and tests with
different materials. I have made TATP before once but I thought I would just skip over that one. I have been trying to think up a detonator that I can
make fairly easily and readily and have a consistent procedure for it. I would probably use something along the lines of straw or pen case, one end
sealed with epoxy or hot gun glue, each cut a few inches long, filled with HMTD, somehow pressed (don't know I would do this yet), fused and expoxied
for sealant, I want to try things like ANNM, ANNMAL, ETN etc. Which brings my other question, is it at all reasonably possible to make inorganic
primaries like Lead Azide without any access to lab chemicals or other fancy appuratis?
I'd also like to try some stuff with small amounts of ETN under 20grams and detonated with heat shock or no primary detonators. I have a lot of
things I want to try and so many thoughts through my head that sometimes it hinders my thinking and don't really know where to start.
Thanks
[Edited on 31-5-2013 by golfpro]
|
|
chemcam
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 423
Registered: 18-2-2013
Location: Atlantis
Member Is Offline
Mood: I will be gone until mid-september, on a work contract.
|
|
Azides are not beginner friendly to synthesize. Well, if you have hydrazine or sodium amide on hand then an azide synthesis is trivial, but, I highly
doubt you have those reagents. A nitrite is also needed but no irregular glassware is required.
20 grams of ETN is not a small amount, 1-2g is a small amount good for beginners, although, even that can severely disfigure or destroy your
hands/ears/eyes.
I don't understand what you are asking? You want help with what?
[Edited on 5-31-2013 by chemcam]
|
|
golfpro
Banned
Posts: 179
Registered: 18-5-2013
Member Is Offline
Mood: Cap Sensitive
|
|
I have thought that ETN in too small amounts would not detonate or would be hard to detonate. Maybe not as much as 20g there. But wouldn't I need more
to do a heatshock detonation or should I forget about that and just use a primary.
Just wanted peeoples opinion on if there is any safe way of using HMTD as a cap and what would this involve, does the HMTD need to be pressed if used
in a straw?
|
|
chemcam
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 423
Registered: 18-2-2013
Location: Atlantis
Member Is Offline
Mood: I will be gone until mid-september, on a work contract.
|
|
A single well-formed needle crystal, <5mg, of ETN in aluminum foil will detonate by heat shock with no problem. Without Al foil I have no idea,
never tried. High-order would obviously need a bigger amount but 2-3mg rips open a soda can. -_-
I can't see any peroxide as being safe but there are smarter ways to go about using them if you absolutely have to. There are other primaries much
safer you should look into. Depends what reagents and equipment you have though.
[Edited on 6-1-2013 by chemcam]
|
|
Ral123
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 735
Registered: 31-12-2011
Member Is Offline
Mood: No Mood
|
|
You want safety, reliability, performance, easy of making and all that with almost no reagents. I'll try to post a synth. of the pseudo primary Lead
nitrophospite. I guess it will work for ETN.
|
|
Farnsworth
Harmless
Posts: 37
Registered: 11-5-2012
Member Is Offline
Mood: No Mood
|
|
Here is a relevant patent
I came up with a detonator using this information a few years ago.
I made one minor modification by adding a little bit of lightly pressed ETN (~150mg) to the bottom of the cap as a booster. The main charge is
(currently) 2.4 grams of a common lead styphnate/barium nitrate mixture. Use a strong metal confinement and beware of shrapnel.
For safety's sake I'll give you one warning - most supply sources for that mixture DON'T WORK, as they're contaminated with other chemicals. Go MSDS
hunting - you want the lead and barium compounds and NOTHING ELSE.
-Philo
Attachment: PATENT - Lead Styphnate Detonators GB139811A.pdf (175kB) This file has been downloaded 677 times
|
|
jpsmith123
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
Here's a patent on a CuO/Al/Si/Bi2O3 thermite based detonator, and also a paper on it.
Attachment: WO2011106803A1.pdf (253kB) This file has been downloaded 690 times
Attachment: Ilunga_Effect(2011).pdf (595kB) This file has been downloaded 637 times
Edit:
I should mention that in several places in the text of these documents, the numbers are apparently mixed up; e.g., in the abstract of the paper the
respective parts by weight of the several ingredients are backwards. Likewise for table 2 in the patent.
[Edited on 2-6-2013 by jpsmith123]
|
|
Rosco Bodine
Banned
Posts: 6370
Registered: 29-9-2004
Member Is Offline
Mood: analytical
|
|
Here is a link to a thread related to use of CuO / Al
http://www.sciencemadness.org/talk/viewthread.php?tid=22599&...
|
|