learningChem
Hazard to Others
Posts: 182
Registered: 21-7-2011
Member Is Offline
Mood: No Mood
|
|
DIY condenser
   
|
|
|
learningChem
Hazard to Others
Posts: 182
Registered: 21-7-2011
Member Is Offline
Mood: No Mood
|
|
.
   
|
|
|
learningChem
Hazard to Others
Posts: 182
Registered: 21-7-2011
Member Is Offline
Mood: No Mood
|
|
.
    
|
|
|
radagast
Hazard to Self
Posts: 79
Registered: 28-6-2012
Location: NYC
Member Is Offline
Mood: No Mood
|
|
Quite Clever
With a little more work, you can turn that into a setup for microdistillation.
http://www.erowid.org/archive/rhodium/chemistry/equipment/mi...
|
|
|
learningChem
Hazard to Others
Posts: 182
Registered: 21-7-2011
Member Is Offline
Mood: No Mood
|
|
Thanks for the link radagast! That looks interesting. Now I need to practice making T joints...
----------
reflux version of the condenser - pic attached.
[Edited on 16-2-2013 by learningChem]
|
|
|
Doc B
Hazard to Others
Posts: 107
Registered: 5-4-2012
Member Is Offline
Mood: No Mood
|
|
Won't the plastic in contact with the glass fail upon being heated by the incoming vapor?
|
|
|
radagast
Hazard to Self
Posts: 79
Registered: 28-6-2012
Location: NYC
Member Is Offline
Mood: No Mood
|
|
Good point; might have to use some kind of heat-resistant plastic and epoxy for those areas.
On an unrelated note, if you used a larger centrifuge tube, you could just pack the tube with small ice cubes without needing to circulate water
through it. This could be useful for small-scale distillation of low-boiling chemicals.
|
|
|
learningChem
Hazard to Others
Posts: 182
Registered: 21-7-2011
Member Is Offline
Mood: No Mood
|
|
Doc B
Yes, I thought that could happen. But notice that the (blue) plastic that surrounds the hot glass tube is in contact with cold water too. I'm
guessing the temperature in that area can't get too high, and it (no doubt) is lower than the temperature of the vapor.
I've used the condenser to distill water mixtures, and to distill toluene and it did work flawlessly. It would be interesting to test it at higher
temperatures though.
radagast,
Yes, that may be another option. I don't know if I can get bigger centrifugue tubes than the one I have though... (I didn't see them at the shop, but
maybe I'd need to ask). (Also, a potential problem is all the ice melting?)
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
A lot of work for a readily available object.
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
|
Bot0nist
International Hazard
Posts: 1559
Registered: 15-2-2011
Location: Right behind you.
Member Is Offline
Mood: Streching my cotyledons.
|
|
Yes, but nothing is quite as rewarding as making your first flammable spirits from white wine, in a home-rigged condenser! Your bringing me back.
Ahhh, nostalgia. Back when I had to be resourceful, because I had no resources!
Good job on the little project learningchem. That little guy might work for some small scale, slow distillations of fairly tame solutions. Now, save
up and get a couple 30cm boro condensers and a ground glass setup. Then it all really opens up to you.
Best of luck.
The Bot.
U.T.F.S.E. and learn the joys of autodidacticism!
Don't judge each day only by the harvest you reap, but also by the seeds you sow.
|
|
|
learningChem
Hazard to Others
Posts: 182
Registered: 21-7-2011
Member Is Offline
Mood: No Mood
|
|
| Quote: | | A lot of work for a readily available object. |
Well...Bending the glass takes two minutes at most. And making a few holes in a piece of soft plastic takes a couple of minutes too. The only 'hard'
part is making the holes a bit smaller than the glass tube diameter, so that the fit is tight.
Bill of materials :
Centrifugue tube - $0.40
25 cm glass tube - $0.40
2 connectors for aquarium tube - $0.20
I don't think small condensers are readily available here, though they may be in other parts of the world =P
|
|
|
learningChem
Hazard to Others
Posts: 182
Registered: 21-7-2011
Member Is Offline
Mood: No Mood
|
|
Bot0nist
Thanks for your message =] - And yeah, I'll probably get a 'real' distillation kit in the future.
|
|
|
Fluorite
Hazard to Others
Posts: 139
Registered: 26-12-2018
Location: United Arab Emirates
Member Is Offline
|
|
I love it *•* I can buy a big neon light tube maybe I can make a condenser since I can't buy anything but I'm a little concerned about the mercury
in the lamp I don't want to distill nitric acid and get a poisonous mercury Nitrate solution 
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
If China ships there, you have the worldwide selection at your disposal for few bucks. Only countries they don't like to ship are like Iraq and
Somalia, they even ship North Korea. 
|
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
Quote: Originally posted by Fluorite  | | I love it *•* I can buy a big neon light tube maybe I can make a condenser since I can't buy anything but I'm a little concerned about the mercury
in the lamp I don't want to distill nitric acid and get a poisonous mercury Nitrate solution |
you won't get any mercury nitrate, neon tubes have tiny beads of mercury+mercury vapour. As you break the sealed tube the mercury vapour will just
diffuse away, visible mercury beads will just roll out the tube.
| Quote: Originally posted by Fyndium |
If China ships there, you have the worldwide selection at your disposal for few bucks. Only countries they don't like to ship are like Iraq and
Somalia, they even ship North Korea. |
in 7 years things probably changed for learningChem
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
Fyndium
International Hazard
Posts: 1192
Registered: 12-7-2020
Location: Not in USA
Member Is Offline
|
|
Ah, my bad. I always forget to check the date.
On the other hand I'm the archeologist who digs up 18 years old topics if they match the context if I find one by search instead of making new thread.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
