chief
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 630
Registered: 19-7-2007
Member Is Offline
Mood: No Mood
|
|
BariumCarbonate from BariumSulfate + Soda
I want to cook BaSO4 with Na2CO3 to get BaCO3 (+ Na2SO4)
This is said to work to 100 % (no BaSO4 left in the BaCO3), when cooked with concentrated soda-solution over quite a while.
My experience is: Some 20-30% BaCO3, rest BaSO4, even with quite concentrated solutions, 3-5 times the stoechiometric amount of soda and 12+ hours of
cooking.
How can I get clean BaCO3 (in an time-economic manner) by this cooking-procedure (several cookings, washing etc.) ? (Have tried the melt, but it has
to be _milled_, quite hard stuff, don't want that)
My BaSO4-powder is quite fine (average grain-size 6 micrometers).
|
|
not_important
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
I think you answered your own question. You need to remove sulfate from the reaction mix to force the reaction, so repeated ( cooking, filter+wash )
cycles is what needs to be done. The wash doesn't need to be really thorough, just remove most of the Na2SO4.
A really large excess of Na2CO3 over remaining BaSO4 helps, say 10 to 15 times excess; industrially the used solution would be fractionally
crystallised to recover much of the unreacted soda for further use.
If you are after the barium carbonate to make other barium compounds from, then you just live with some sulfate and filter it out of the solution of
the barium salt.
In analytic chemistry, the melt method also used a many times excess of soda, treatment with hot water left a fairly fine powder of BaCO3 after the
sodium salts were dissolved away.
|
|
chief
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 630
Registered: 19-7-2007
Member Is Offline
Mood: No Mood
|
|
Interesting: Crystallize the soda; I have thought about that, but the solubilities at 20 and 100 [Celsius] (Na2CO3, Na2SO4) are so similar that it
seemed to not be very applicable. At least one would want to remove the Na2SO4, so the soda could be used again for the same process ? May be
partially recycle the soda, but at low efficiencies ? (Always to use about twice the stoechiometric soda-amount per mol BaCO3 ?)
|
|
S.C. Wack
bibliomaster
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2419
Registered: 7-5-2004
Location: Cornworld, Central USA
Member Is Offline
Mood: Enhanced
|
|
100% may be a stretch. Maybe 99.5% only. You should look into "what is said" for improvement to your experience:
http://dx.doi.org/10.1021/ac50065a014
|
|
chief
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 630
Registered: 19-7-2007
Member Is Offline
Mood: No Mood
|
|
Great link ! Only that I have no access there; but the first (free) page contains enough info ... .
|
|
FrankRizzo
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 203
Registered: 9-2-2004
Member Is Offline
Mood: No Mood
|
|
Here ya are chief.
Attachment: ac50065a014.pdf (456kB) This file has been downloaded 1251 times
|
|
I am a fish
undersea enforcer
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 600
Registered: 16-1-2003
Location: Bath, United Kingdom
Member Is Offline
Mood: Ichthyoidal
|
|
Barium sulfate and sodium carbonate are both very cheap, and so (on a small scale) it's perfectly acceptable to sacrifice efficiency for quality.
Take your crude BaSO4, BaCO3, Na2SO4, Na2CO3 and H2O mixture, and collect the insoluble components by filtration.
Add a nominal excess of hydrochloric acid to the resulting BaSO4/BaCO3 mixture, and filter to give a solution of BaCl2 and HCl.
Next, add a nominal excess of Na2CO3 solution, and the resulting precipitate will be pure BaCO3.
1f `/0u (4|\\| |234d 7|-|15, `/0u |234||`/ |\\|33d 70 937 0u7 /\\/\\0|23.
|
|
chief
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 630
Registered: 19-7-2007
Member Is Offline
Mood: No Mood
|
|
Great Idea !!! I have a lot of Ba(NO3)2, instead the BaCL2 . Thank you !!!
|
|
tetrahedron
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 210
Registered: 28-9-2012
Member Is Offline
Mood: No Mood
|
|
ok i did the math on this, trying to figure out how efficient it is in theory. we have two equilibria1:
1.
BaCO3 <---> Ba2+ + CO32-
K1 = 2.58 * 10-9
2.
BaSO4 <---> Ba2+ + SO42-
K2 = 1.08 * 10-10
at the beginning we have a suspension of BaSO4 in a Na2CO3 solution of molarity a. in the absence of
other species the BaSO4 dissociates slightly and causes for Ba2+ and SO4 to reach molarity b each.
together, a new equilibrium is formed; CO32- steals some Ba2+ (let's say c mol/L) and precipitates
(equation 1, from right to left); as a consequence, further BaSO4 goes into solution (let's say d mol/L) (as in equation
2). at equilibrium, the solubility products hold:
K1 = [Ca2+] * [CO32-] = (b - c + d) * (a - c)
K2 = [Ca2+] * [SO42-] = (b - c + d) * (b + d)
---> (b + d)/(a - c) = K2 / K1
and
(K1 / K2 + 1) * (b + d)2 - a * (b + d) - K2 = 0
which resolves to
b + d = a * (1 + sqrt(1 + 4 * (K1 + K2) / a2)) / (2 * (K1 / K2 + 1))
the ratio inside the square root is small, so this approximates to
a / (K1 / K2 + 1) = 4.02% a (*)
i.e. the final molarity of sulfate ions (which roughly indicates how much the metathesis progressed) is about 4% of the initial molarity of sodium
carbonate dissolved. of course this says nothing about how fast the equilibrium is reached.
i also tried to work out the problem with CaF2 instead of BaSO4, but this seems to involve more than a simple quadratic
equation, due to fluoride being monovalent ![:(](./images/smilies/sad.gif)
[1]
solubility products @ 25°C:
http://www.ktf-split.hr/periodni/en/abc/kpt.html
edit. it's clear from (*) that the stoichiometry of the undissolved substances plays no role. you wanna use an
'excess' Na2CO3 in the sense that you want it well saturated (i.e. a = 4.29 M @ 100°C), while at the same time
you shouldn't mix in more BaSO4 than can be 'digested' (i.e. about 4% of 4.29 M, or 0.171 M) because the equilibrium represents a barrier
that can't be crossed.
running the computation with calcium sulfate (more soluble) instead of barium sulfate, the value in (*) is over 99% of
a.
using an approximation, it turns out that the fluoride in CaF2 can be leached to the extent of about 0.174 M for the same 4.29 M of
Na2CO3.
[Edited on 6-10-2012 by tetrahedron]
|
|
tetrahedron
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 210
Registered: 28-9-2012
Member Is Offline
Mood: No Mood
|
|
here goes:
a = [Ca2+]start
b = [F-]start
c Ca2+ + c CO32- ---> c CaCO3 (s)
d CaF2 ---> d Ca2+ + 2d F-
K1 = [Ca2+]end * [CO32-]end = (a - c + d) * (a - x)
K2 = [Ca2+]end * [F-]2end = (a - c + d) * (2 * (b + d))2
this system of equations gives (i'll spare you the details)
16 K1 x4 + 4 K2 x3 - 4 K2 a x2 - K22 = 0
where x = b + d. this intractable quartic can be reduced to
4 K1 x4 + K2 x3 - K2 a x2 ~~ 0
using the approximation K22 = 0. the only plausible solution is
x ~~ (- K2 + sqrt(K22 + 16 K1 K2 a)) / (8 K1)
here's where you can plug in a = 4.29 M and get x = 8.69 * 10-2 M, i.e. about 0.174 M of fluoride, as in
my previous post. note that the ratio K2 / K1 is so small that (for a not too small) we can
further approximate
x ~~ sqrt(K2 * a / (4 * K1))
i.e. the efficiency of the methathesis only increases with the square root of the initial concentration of Na2CO3 for the
monovalent anion F-, as opposed to linearly in the case of the divalent anion SO42-.
|
|