Farnsworth
Harmless
Posts: 37
Registered: 11-5-2012
Member Is Offline
Mood: No Mood
|
|
Acid Resistant Coating for Storage Purposes?
I'm looking for something interesting.
Suppose one needed to store small amounts of mixed nitric and sulphuric acid in a non-acid resistant container. I know this is an unusual situation,
but it is leading me into a particular experiment. For practical reasons I cannot use glass (unusual container geometry and I'm not a professional
glass blower, basically.)
Are there any commercially available or synthable materials that could coat the inside of a metal or plastic container to make it resistant to the
acid for an extended period?
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
Er... plastic? As far as I know, plastic is immune to acids. If I'm wrong, you could try Teflon.
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Yes, HDPE should do it. Starting from powder, 'rotamoulding' can be used to coat the inside of vessels, even oddly shaped ones.
[Edited on 17-7-2012 by blogfast25]
|
|
polymerizer87
Harmless
Posts: 35
Registered: 16-7-2012
Member Is Offline
Mood: No Mood
|
|
I have a synth for a acid resistant polymer they use as a coating for various products such as the interior of metal canisters. Although im not sure
what your availability is for solvents such as n methyl pyrrolidone and o-xylene. The polymer is extremely easy to apply and just needs to be thrown
in a 300 C oven to cure.
|
|
Endimion17
International Hazard
Posts: 1468
Registered: 17-7-2011
Location: shores of a solar sea
Member Is Offline
Mood: speeding through time at the rate of 1 second per second
|
|
Teflon is a plastic.
HDPE, s mentioned, is ok. Not all plastic masses are inert to all common acids, but HDPE would be ok for mixture of nitric and sulphuric acid, if they
aren't hot.
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Teflon is expensive and difficult to adhere to anything. It's a bit overkill for this application, IMHO...
|
|
AJKOER
Radically Dubious
Posts: 3026
Registered: 7-5-2011
Member Is Offline
Mood: No Mood
|
|
Here is an alternative possible solution (?) that can be molded into shapes, scaled up, relativity inexpensive and generally availablel. Make vessels
out of Plaster of Paris (CaSO4) and line with a suitable thin plastic sheet.
Obviously resistant to H2SO4, and the reaction:
CaSO4 + 2 HNO3 --> Ca(NO3)2 + H2SO4
may proceed slowly depending on temperature and the starting presence of H2SO4.
Downside: a short term solution as penetration of the plastic lining will introduce a Calcium contamination as Nitric acid attacks the CaSO4, and the
vessel itself would be fragile.
Those with some working knowledge of pottery may also have some creative ideas as to composition and shapes.
[Edited on 17-7-2012 by AJKOER]
|
|
Twospoons
International Hazard
Posts: 1321
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Isn't paraffin wax used to line glass bottles for storing HF? Maybe you could adapt that approach.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|