MR AZIDE
Hazard to Self
Posts: 64
Registered: 21-5-2012
Location: UNITED KINGDOM
Member Is Offline
Mood: Fizzing
|
|
Molybdenum metal.
Has anyone ever collected blown tungsten filament bulbs, bust them open and collected enough of the fine support wires that are supposedly made of
Molybdenum, to make any compounds from the Molybdenum?
Maybe some didn't realize the the supporting wires for the filament are made of Mo??????
|
|
|
DoctorOfPhilosophy
Hazard to Others
Posts: 130
Registered: 12-6-2012
Location: Ontario, Canada
Member Is Offline
Mood: enthralled
|
|
Yep, I used to pull burnt/broken halogen lights from a construction site and pull out the W and Mo. I'm not sure if it's Mo, but they're still lying
in my periodic table so if you propose a test I'll post the results.
|
|
|
vmelkon
National Hazard
Posts: 669
Registered: 25-11-2011
Location: Canada
Member Is Offline
Mood: autoerotic asphyxiation
|
|
You mean the thin wires that support the filament?
http://www.ehow.com/list_6623245_minerals-light-bulb_.html
Since when have they been using Mo? I had not heard about it previously.
More stuff
http://www.ushio.com/support/faqs.htm
"Why is molybdenum foil used inside the halogen lamp?
Molybdenum foils is used as a conductor through the seal part of lamp. It insures the hermetic sealing of the lamp. Molybdenum has almost the same
thermal expansion properties as quartz. "
[Edited on 29-6-2012 by vmelkon]
|
|
|
Endimion17
International Hazard
Posts: 1468
Registered: 17-7-2011
Location: shores of a solar sea
Member Is Offline
Mood: speeding through time at the rate of 1 second per second
|
|
I've heard about molybdenum being used for filament support a long time ago (pure or alloyed, don't know), but I've also read somewhere it's not being
used anymore. That's all I can tell at this point.
|
|
|
daragh8008
Hazard to Self
Posts: 61
Registered: 15-10-2008
Location: Eire
Member Is Offline
Mood: Happy
|
|
I have lots of Molybdenum metal coated with gold. We use it for our gold evaporator and when it blows we just keep it. Wouldn't anyone have any easy
methods of separating the gold from the Mo metal for recovery??
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Treatment with Aqua Regia and precipitation of the Au with sodium metabisulphite (after partial neutralisation) should work.
|
|
|
plante1999
International Hazard
Posts: 1936
Registered: 27-12-2010
Member Is Offline
Mood: Mad as a hatter
|
|
Molybdenium is not very similar to gold, Maybe HCl/chlorine would only dissolve gold. Generaly when disolving gold plating we use 20% HCl with small
amount of sodium hypochlorite in it to leach the gold.
I never asked for this.
|
|
|
Wizzard
Hazard to Others
Posts: 337
Registered: 22-3-2010
Member Is Offline
Mood: No Mood
|
|
Grinding, then heating will release Mo trioxide, which evaporates above 1150*c, which is also slightly water soluble (yeilding molybdic acid).
|
|
|
chornedsnorkack
National Hazard
Posts: 564
Registered: 16-2-2012
Member Is Offline
Mood: No Mood
|
|
Molybdenum also dissolves in hydrofluoric/nitric acid mixture. At higher temperatures, molybdenum metal reacts with molten alkali and with molten
alkali metal nitrates.
|
|
|
cyanureeves
National Hazard
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
daragh8008 you have lots? you mean plated?peroxide and hcl acid releases the gold from copper maybe it will do the same with molybdenum and maybe its
got alot more gold surface than computer gold. if it doesnt peel the gold then aqua regia as suggested will do the trick. just let it evaporate after
dissolving and add sodium metabisulfate.
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by cyanureeves  | | daragh8008 you have lots? you mean plated?peroxide and hcl acid releases the gold from copper maybe it will do the same with molybdenum and maybe its
got alot more gold surface than computer gold. if it doesnt peel the gold then aqua regia as suggested will do the trick. just let it evaporate after
dissolving and add sodium metabisulfate. |
"peroxide and hcl acid releases the gold from copper maybe it will do the same with molybdenum"
What precisely do you understand by 'releases'?
And I do wish people wouldn't use LOLtext for chemical formulas ("hcl") 
[Edited on 1-7-2012 by blogfast25]
|
|
|
daragh8008
Hazard to Self
Posts: 61
Registered: 15-10-2008
Location: Eire
Member Is Offline
Mood: Happy
|
|
I suppose I should clarify what I meant. the coater takes a strip of Mo about 3cm by 1cm formed into a little boat. We buy in sheets of the stuff and
shape it ourself. I'm not sure what the thickness of the sheet is but somewhere around 0.2 - 0.5 mm. I have at least 20 used boat of Mo almost all
with gold left in them. In some the gold is very little as Au is generally green when it is thiner than about 10nm in others there appears to be up
1-2mm of gold stuck to the Mo metal when the boat went. It would be nice to just release the gold from the Mo. I may try the peroxide hcl method
first. I don't have any nitric acid but I often work with molten nitrates so I may give that a shout also. I did once also dissolve very thin
coatings of gold with NaCl solution and a Hg lamp, these were however very thin sputtered gold coatings ~1-2nm so I don't think that would be a route.
I suppose Aqua Regia is the best was but I don't have any nitric acid so for the time being it is not an option.
|
|
|
cyanureeves
National Hazard
Posts: 744
Registered: 29-8-2010
Location: Mars
Member Is Offline
Mood: No Mood
|
|
daragh8008 thank you for that information. i have plated gold items and have gotten a greenish hue before,very interesting.
@blogfast by releases i meant that gold will separate as foils and float around in the sloution and i dont really know how it happens. do you mean HCl
does not need the word acid next to it?ha.ha i understand
[Edited on 2-7-2012 by cyanureeves]
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by cyanureeves |
@blogfast by releases i meant that gold will separate as foils and float around in the sloution and i dont really know how it happens.
|
In all likelihood the HCl/peroxide mixture attacks the underlying metal slightly, thus destroying any bonding between the gold plating and the bulk
metal. Some gold recoverers (from e-waste) use nitric acid to release the gold coatings from their substrates.
|
|
|
daragh8008
Hazard to Self
Posts: 61
Registered: 15-10-2008
Location: Eire
Member Is Offline
Mood: Happy
|
|
So I don't know much about Mo, would it be attacked by HCl / peroxide mix? I always assumed Mo was used as it fairly resistant to oxidation thus the
peroxide would be fairly useless. ( although I often use this mix for etching Cu2O to good effect) @ cyanureeves : what we find is that glass coated
with thin layers by evaporation are green but when the excess gold is peeled from the evaporator instrument it has the usual gold colour with a green
hue. Because it is built up of dozens of coats it is very flaky. I assume between coats atmospheric contaminants build up to separate the next
evaporated layer. giving it it's flaky texture and greenish hue
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
I would expect attack to be minimal.
|
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
| Quote: | Maybe some didn't realize the the supporting wires for the filament are made of Mo??????
|
In this 'How it's made - Incandescent Light Bulb' video they don't say what the wires themselves are made of, but do say that they are coated with
zirconium:
http://www.youtube.com/watch?v=BylLOWRojyY&feature=g-vre...
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer |
|
|
elementcollector1
International Hazard
Posts: 2684
Registered: 28-12-2011
Location: The Known Universe
Member Is Offline
Mood: Molten
|
|
I did pull out a few support wires from lightbulbs, and bought a rod of molybdenum to compare. Two years later, both have the exact same black
tarnish, so it's not steel or tungsten.
[Edited on 3-23-2014 by elementcollector1]
Elements Collected:52/87
Latest Acquired: Cl
Next in Line: Nd
|
|
|
Texium
Administrator
Posts: 4618
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
Wow, that's awesome. I accidentally broke a lightbulb earlier today and saved the tungsten, but I had no idea the those support wires were Mo! I would
have thrown it away otherwise. That's great!
Edit: Also, the lightbulb that I broke was a couple years old and the support wires also appear to have that black tarnish that you describe.
[Edited on 3-23-2014 by zts16]
|
|
|
Zephyr
Hazard to Others
Posts: 341
Registered: 30-8-2013
Location: Seattle, WA
Member Is Offline
|
|
Yes, that is very useful, anther addition to my periodic table.
But, is there any way to chemically test the filament support to determine is it is molybdenum besides waiting several years for it to gain the black
coating?
|
|
|
Texium
Administrator
Posts: 4618
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
I don't know… I just went looking for information about reactions involving metallic Mo, but with very little luck. If you heat it to above
600˚C it will form molybdenum trioxide according to Wikipedia, which has conflicting information as to what MoO3 actually looks like, since they
have a picture of a gray powder, but say that it is either yellow or blue.
My chemical reference book says that it's whitish yellow, so I'd go with that. It also says that molybdenum metal has a density of 10.2 g/cc, if you
have enough to measure that.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
