| Pages:
1
..
3
4
5
6
7
..
9 |
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
I have recently tried a preparation of calcium malonate using an older procedure by Subramaniam et al, as offered by DJF90. This procedure, as
excerpted, is shown below:
"Oxidation of Malic Acid by Hydrogen Peroxide in the Presence of Ammonia.
dl-Malic acid (5 g.) was dissolved in a 20-volume (6%) solution of hydrogen peroxide (100 c.c.), and the liquid was made just alkaline with
concentrated aqueous ammonia and diluted to 150 C.C. with water. After 30 hours the reaction mixture was shaken with animal charcoal (5 g.) to remove
the undecomposed hydrogen peroxide still present. The solution was filtered, boiled, and treated with an excess of calcium chloride solution. After
concentration to 100 C.C. and subsequent standing for 3 days, the white crystalline precipitate (5.25 g.) was collected, washed with water, and dried
in a vacuum [Found : Ca, 21.7. Calc. for CH2(CO*O),Ca,2H20: Ca, 22.3%].
A quantity of this calcium salt (1-5 g.) was heated in a sealed tube with glacial acetic acid (5 c.c.) and freshly distilled cinnamaldehyde (30 drops)
at 100" for 10 hours. The product was purified as detailed in a previous case and yielded 0.32 g., which melted at 208" (decomp.), alone or mixed with
authentic cinnamylidenemalonic acid of m. p. 208" (decomp.) (0.1510 g. required 274 C.C. of NI20-NaOH. Calc., 27.7 c.c.)."
A white precipitate of the stated weight was indeed obtained. However, extraction of the acidified salt with ether did not yield the desired malonic
acid.
Although a method for identifying the salt as a malonate is presented in the article, it appears cumbersome. Does anyone have any other suggestions
as to how putative Ca malonate can be identified?
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
experimenter
Harmless
Posts: 19
Registered: 7-11-2010
Member Is Offline
Mood: No Mood
|
|
By reacting glycerol with HCl/ZnCl2 (Lucas test) the middle hydroxyl group (OH) could be substituted by Cl. So you get CH2(OH)-CHCl-CH2(OH). From
this, substitute the chloride ion with hydrogen (using Zn) in order to obtain 1,3 propanediol. Oxidize this to the malonic acid.
I don't know if this could work. Probably you will see no turbidity in the first reaction because the chlorinated product is water-soluble (because of
two hydroxyl groups). Isolation of this product from the unreacted glycerol could be another problem.
|
|
|
Roger86
Harmless
Posts: 31
Registered: 17-8-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Magpie  | | Malonate salts are indeed present in the juice of beets. Precipitation of Ca malonate is a problem for industrial refiners of sugar beets. It is
present at something around 2% in sugar beets IIRC. It would be an interesting challenge to extract malonate from beets IMO. |
If its intresting, then i hope you dont mind in helping me,i decided to do just that
I think that getting calcium malonate from beetroot is an achivement id like to have, has anyone written extraction guide yet, because id like to try,
im not expert at chemistry but i have degree as a lab worker and i dont mind trying many times
what i believe i should do first is to make some calculations on economics
in my country beetroot costs 0,9€ per kilogram and if there is 2 % calcium malonate the price of extracted malonate at 0% loss would be 45€ per
kilogram witch would be a good price, and i also like doing some cooking
Since its economicaly a sound plan im going to start my experiments next monday when i get some money for chemicals
and of course the game plan, witch i hope i can get some feedback on
1.Im going to cut the beetroot to slices and boil them in water for some amount of time, since i have no experience in cooking beetroot i have no idea
for how long, but i will do so for as long as it takes to soften them up.Then im going to use blender to break the stuff in to a paste,to help the
color dissolve in water.I know from a reliable source that calcium malonate will not dissolve in water.There is no source as to how low the solubility
is but what iv read, calcium malonate is 'cheese like precapitate'.im going to save the water and drink it for its vitamins and antioxidants.
2.im going to put fresh water in and put the beetroots from steel cooking pot to plastic bucket and add some acid, i plan to use sulfuric from battery
acid.Battery acid should be pretty pure ~30%.Calcium sulfate is going to precapitate at this point.Maybe, i might not see anything because calcium
malonate is already insoluble, it might just get replaced by the sulfate.
3.Im going to filter the liquid that i get from that. I should now have pink malonic acid solution.Now this is the part id need theoretical
help.Should i now proceed with options;
a)dry this off (pain in the ass) and esterify and distill.
b) use calcium compound to precapitate it and then wash with water
c)put non water miscible solvent like ether and extract with that
As a conclusion,i know that im not going to get pure stuff, its going to be contaminated with the red color and some organics from the vegetable, but
i dont really need it to be analytically pure.I dont even have a use for malonic acid yet but i wanted to do some kitchen friendly chemistry for a
while.
Has someone already done this, and if can i get link to the quide?if not i'd like to make experiments and reading and write the guide.
Ps.should i use beetroot or sugar beet?
[Edited on 17-8-2011 by Roger86]
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
Here's a reference you might want to read:
http://pubs.acs.org/doi/pdf/10.1021/ie50495a018
I have never tried this. I do have in my notes that the industrial juice extraction was done at 70-74C for 100 minutes.
Ether extraction may be the best way to separate the malonic acid from the other water solubles such as amino acids. Other acids may tag along with
the malonic acid.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
manimal
Hazard to Others
Posts: 180
Registered: 15-1-2008
Member Is Offline
Mood: ain't even mad
|
|
How about the oxidative decarboxylation of aspartic acid with TCCA, followed by hydrolysis of the nitrile?
|
|
|
FrankMartin
Hazard to Self
Posts: 50
Registered: 30-5-2010
Member Is Offline
Mood: No Mood
|
|
Synthesis of Malonic acid...
This may be done via enolate (crossed claisen) chemistry, vis:
Etn-Butyrate + DiEthylCarbonate = diethyl ethylmalonate + EtOH
Using NaEthoxide as a reagent.
The "diethyl ethylmalonate" is also known as "Ethyl Malonic Ester"
Presumably simple DiEthylMalonicAcid needs EtAcetate instead of Etn-Butyrate.
This patent gives this and similar examples:
US2367632 And the process is/was called "Carbalkoxylation"
Regards.
Frank
|
|
|
Roger86
Harmless
Posts: 31
Registered: 17-8-2011
Member Is Offline
Mood: No Mood
|
|
As i sayed i started today working towards OTC source of malonates.With attachement is a quide i wrote for myself, please help me to improve it.I got
to step 7 today.Tomorrow im going out to the hardware store to buy some impure NaOH and some CaCl2.
But, i cooked the vegetable for 60 minutes, untill it got soft, i didnt have blender so i just let the H2SO4 work for 15 minutes with mixing.
I did some reading and it seems that the colour of the beetroot is dependent on PH.I washed most of the colour from the plant away, but when sulfuric
acid was added, the colour became more violet than red.Now i have 1,5dl of beetroot juice with sulfuric acid in it(actually, from this point it
smelled like blackcurrants. I plan to make it basic with lye and put CaCl2 to make it precapitate.I read that the violet color turns to yellow at
caustic PH.
When i'm done with this quide, is it ok to have link to my guide, or do i just post it here as document? problem is that upload limit is 2MB witch
doesnt leave much to get creative with...
And i read Magpie's link, would it be possible to get glutamic acid from it too? because i would love to have some GABA
Attachment: Calcium Malonate.rtf (1kB)
This file has been downloaded 1028 times
|
|
|
Ebao-lu
Unregistered
Posts: N/A
Registered: N/A
Member Is Offline
|
|
[edited]
[Edited on 23-8-2011 by Ebao-lu]
|
|
|
bbartlog
International Hazard
Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline
Mood: No Mood
|
|
Not sure where you got your procedure, but I believe you will precipitate CaSO4 along with your calcium malonate. 2NaOH + H2SO4 -> Na2SO4 + 2H2O,
then CaCl2 + Na2SO4 -> 2NaCl + CaSO4 (driven by solubility as the CaSO4 is relatively insoluble). This may not be an insuperable objection if you
have some way in mind to separate calcium malonate from calcium sulfate, but in any case don't assume that all that white precipitate is malonate.
|
|
|
Roger86
Harmless
Posts: 31
Registered: 17-8-2011
Member Is Offline
Mood: No Mood
|
|
I dont expect the precapitate to be pure malonate, the process is so that i dont have to evaporate tons of water.I now have a plan to esterify the
malonic acid to make diethylmalonate and then distill.
I havent added the calcium chloride yet, so i havent really made the mistake yet
But, i could always separate malonic acid from the sulfuric acid by just letting it dry, couldnt i? i suspect its going to be a very long process, but
as i stated earlier, im not afraid to do some hard work
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
I went to the library and looked up the article in the scientific journal I cited above. Did you? There is absolutely no mention of malonic acid or
malonates in this article. This articles covers the analysis of the contents of juice extract of sugar beets from at least 3 different regions of the
US.
I have done a little researching and can find no reference to malonates in beets in scientific journals. Several, however, make reference to
malic acid or malates. So, I don't know why Wiki and its clones keep mentioning malonic acid as a constituent of beets.
I think that the separation of a particular organic acid or its salt from beet juice would be difficult. The scientists resorted to several different
ion exchange resins to get these acid anion separations.
[Edited on 23-8-2011 by Magpie]
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
Roger86
Harmless
Posts: 31
Registered: 17-8-2011
Member Is Offline
Mood: No Mood
|
|
I advanced in my work, i got to step 8
Turns out that you get precapitate even without CaCl2, not much but the precapitate would indicate that i have saturated solution of sodium malonate,
and i used very dilute acid and base, so i have a lot of the solution.I never learned to make in small amounts.Would i be optimistic to assume that
the precapitate is sodium malonate?
I checked that Encylopedia Britannica also states that there is calcium malonate in beetroot
http://www.britannica.com/EBchecked/topic/360443/malonic-aci...
And if both Wikipedia and Encylopedia Britannica say there's some in it, it's worth trying out.
BTW, where did you get the 2% number? If there was 2% it would be in correlation with what i got as what i think is sodium malonate
Also, i read about the acid being unstable, any info on how long i can store it?
Edit. didnt notice you sayed scientific journals, but i trust wiki and Britannica
[Edited on 23-8-2011 by Roger86]
|
|
|
Polverone
Now celebrating 21 years of madness
Posts: 3186
Registered: 19-5-2002
Location: The Sunny Pacific Northwest
Member Is Offline
Mood: Waiting for spring
|
|
| Quote: Originally posted by Magpie | I went to the library and looked up the article in the scientific journal I cited above. Did you? There is absolutely no mention of malonic acid or
malonates in this article. This articles covers the analysis of the contents of juice extract of sugar beets from at least 3 different regions of the
US.
I have done a little researching and can find no reference to malonates in beets in scientific journals. Several, however, make reference to
malic acid or malates. So, I don't know why Wiki and its clones keep mentioning malonic acid as a constituent of beets.
I think that the separation of a particular organic acid or its salt from beet juice would be difficult. The scientists resorted to several different
ion exchange resins to get these acid anion separations.
|
According to several older references, malonic acid is present in sugar beets. No quantitative information was found in these pre-war publications.
Ullmann's says "Malonic acid is found in small amounts in sugar beet and green wheat, being formed by oxidative degradation of malic acid." Malic acid
is not that abundant in beets to begin with. I would guess that while malonic acid is technically present in beets, it's futile to attempt preparative
extraction.
PGP Key and corresponding e-mail address
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
| Quote: Originally posted by Roger86 |
Turns out that you get precapitate even without CaCl2, not much but the precapitate would indicate that i have saturated solution of sodium malonate,
and i used very dilute acid and base, so i have a lot of the solution.I never learned to make in small amounts.Would i be optimistic to assume that
the precapitate is sodium malonate?
|
Yes, sodium malonate is soluble to 148g/L according to:
http://www.chemicalbook.com/ChemicalProductProperty_EN_CB870...
| Quote: Originally posted by Roger86 |
BTW, where did you get the 2% number? If there was 2% it would be in correlation with what i got as what i think is sodium malonate
|
I can't remember where I got that 2%. It is not in my notes.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
querjek
Hazard to Self
Posts: 76
Registered: 26-8-2008
Member Is Offline
Mood: No Mood
|
|
I'm not too sure if this pathway would work--what about :
Serine + oxidant -> 1,3-propanedioic acid 2-amine (sorry if the name is off--I'm out of practice!)
1,3-propanedioic acid 2-amine + HNO2 -> the diazo form of the previous product
diazo compound + reductant -> malonate
What I'm mostly unsure about is the diazotization reaction--I know HNO2 can be kinda finicky depending on the constituents of the compounds involved.
[Edited on 24-8-2011 by querjek]
[Edited on 24-8-2011 by querjek]
it's all about chemistry.
|
|
|
Roger86
Harmless
Posts: 31
Registered: 17-8-2011
Member Is Offline
Mood: No Mood
|
|
I't doesnt matter if this isnt full succes, i know i probably have a mix of inorganics and some malates in the precapitate, but i like trying
things.So if it doesnt succeed, at least i had fun
|
|
|
redox
Hazard to Others
Posts: 268
Registered: 22-2-2011
Location: The Land of Milk and Honey
Member Is Offline
Mood: Chalcogenetic
|
|
| Quote: Originally posted by querjek | I'm not too sure if this pathway would work--what about :
Serine + oxidant -> 1,3-propanedioic acid 2-amine (sorry if the name is off--I'm out of practice!)
1,3-propanedioic acid 2-amine + HNO2 -> the diazo form of the previous product
diazo compound + reductant -> malonate
What I'm mostly unsure about is the diazotization reaction--I know HNO2 can be kinda finicky depending on the constituents of the compounds involved.
[Edited on 24-8-2011 by querjek]
[Edited on 24-8-2011 by querjek] |
Maybe I remember wrong, but I thought diazotisation wasn't possible on aliphatic compounds. The resonance in aromatics stabilizes the diazo compound,
but aliphatic compounds don't have these stabilizing effects. I think when you diazotise your acid it will release nitrogen immediately and form
2-hydroxymalonic acid.
Here's a ref: http://in.answers.yahoo.com/question/index?qid=2011051821215...
My quite small but growing Youtube Channel: http://www.youtube.com/user/RealChemLabs
Newest video: Synthesis of Chloroform
The difference between chemists and chemical engineers: Chemists use test tubes, chemical engineers use buckets. |
|
|
querjek
Hazard to Self
Posts: 76
Registered: 26-8-2008
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by redox | | Quote: Originally posted by querjek | I'm not too sure if this pathway would work--what about :
Serine + oxidant -> 1,3-propanedioic acid 2-amine (sorry if the name is off--I'm out of practice!)
1,3-propanedioic acid 2-amine + HNO2 -> the diazo form of the previous product
diazo compound + reductant -> malonate
What I'm mostly unsure about is the diazotization reaction--I know HNO2 can be kinda finicky depending on the constituents of the compounds involved.
[Edited on 24-8-2011 by querjek]
[Edited on 24-8-2011 by querjek] |
Maybe I remember wrong, but I thought diazotisation wasn't possible on aliphatic compounds. The resonance in aromatics stabilizes the diazo compound,
but aliphatic compounds don't have these stabilizing effects. I think when you diazotise your acid it will release nitrogen immediately and form
2-hydroxymalonic acid.
Here's a ref: http://in.answers.yahoo.com/question/index?qid=2011051821215... |
I've heard that before too about aliphatic compounds. However, could the pH of solution be played with in order to provide resonance stability via the
two carboxylates?
it's all about chemistry.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Alpha-amino acids can be successfully diazotised. See the following discussion from obscure site http://www.sciencemadness.org/talk/viewthread.php?tid=11148
|
|
|
querjek
Hazard to Self
Posts: 76
Registered: 26-8-2008
Member Is Offline
Mood: No Mood
|
|
Haha. Sorry for not using the search here more effectively and thanks for the link!
it's all about chemistry.
|
|
|
Roger86
Harmless
Posts: 31
Registered: 17-8-2011
Member Is Offline
Mood: No Mood
|
|
I really could use data on what malonic acid, sodium malonate and calcium malonate are soluble in, especially if the solvent is non water miscible.I
used google and it didnt provide much help.
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
http://www.sciencemadness.org/talk/viewthread.php?tid=11698&...
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
Roger86
Harmless
Posts: 31
Registered: 17-8-2011
Member Is Offline
Mood: No Mood
|
|
I cant open the page, it says im not permitted
|
|
|
Magpie
lab constructor
Posts: 5939
Registered: 1-11-2003
Location: USA
Member Is Offline
Mood: Chemistry: the subtle science.
|
|
You will have to request permission from an administrator via U2U.
The single most important condition for a successful synthesis is good mixing - Nicodem
|
|
|
bbartlog
International Hazard
Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline
Mood: No Mood
|
|
In this case, though, the reference that is provided in the linked-to post is just a page or two from Atherton Seidell's 1919 book on solubilities.
You can find it in Google Books even if you don't get access to the Reference forum. You may be disappointed, though, as it only gives data for
malonic acid proper and not for the salts; not only that, but it looks like malonic acid is more or less soluble in all of the listed solvents and so
there is no real prospect for crashing it out of solution by addition of some other compound.
My CRC handbook suggests that calcium malonate is rather insoluble, though.
|
|
|
| Pages:
1
..
3
4
5
6
7
..
9 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
