Ophidean
Harmless
Posts: 5
Registered: 8-6-2011
Member Is Offline
Mood: No Mood
|
|
Overhead stirrer
I am not familiar with overhead stirring and i would like to know how to accomplish this. I used to work with magnetic stirring and reflux condenser,
but now I am setting up a 12L 3-neck round bottom flask in which my magnetic stirrer wont suffice anymore(not enough power).
Now how do i use overhead stirring in this? Seeing as how I understand it you put some kind of stir-bar from the top through the neck, but at this
place there will be a liebig condenser?
|
|
|
redox
Hazard to Others
Posts: 268
Registered: 22-2-2011
Location: The Land of Milk and Honey
Member Is Offline
Mood: Chalcogenetic
|
|
Is it not possible to put the stirrer in the center neck, and put the condenser on a side neck?
My quite small but growing Youtube Channel: http://www.youtube.com/user/RealChemLabs
Newest video: Synthesis of Chloroform
The difference between chemists and chemical engineers: Chemists use test tubes, chemical engineers use buckets. |
|
|
Ophidean
Harmless
Posts: 5
Registered: 8-6-2011
Member Is Offline
Mood: No Mood
|
|
Hmm I guess ill just have to rearange then.
But this will not make it less efficient?
Might be a crazy thought, but just feels that way when you use a neck that is diagonal and not straight.
And a second thing: How would i use an overhead stirrer, because normally you can just put a stopper on a neck, and use a magnetic stirrer, but with
an overhead stirrer you will have to keep the neck open for the stirbar? (It of course needs to be sealed for reflux condensing)
[Edited on 8-6-2011 by Ophidean]
|
|
|
azo
Hazard to Others
Posts: 163
Registered: 12-2-2008
Member Is Offline
Mood: No Mood
|
|
Of course you can use mechanical stirring in the centre neck
if your setting up for simple distilation you could use a claisen still head.
regards azo
|
|
|
darel
Harmless
Posts: 27
Registered: 12-7-2008
Member Is Offline
Mood: No Mood
|
|
They are called stir bearings and are ground glass and air tight. I have one for a 19mm driver into a 45/50 ground glass joint. They are lubricated
with silicone oil or you can buy them in teflon. This solves the air tight problem. for stirring with overhead. Now you can have a condenser on one or
both the remaining necks. The gasses will only go to where they can escape to atmospheric pressure the easiest. Here are a few for sale on ebay
currently
http://shop.ebay.com/i.html?_from=R40&_trksid=p5197.m570...
I have a fancy spinning band distillation column that has the spin shaft run through the reflux condenser on top. But this is a custon piece and very
costly.
|
|
|
Ophidean
Harmless
Posts: 5
Registered: 8-6-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by darel  | They are called stir bearings and are ground glass and air tight. I have one for a 19mm driver into a 45/50 ground glass joint. They are lubricated
with silicone oil or you can buy them in teflon. This solves the air tight problem. for stirring with overhead. Now you can have a condenser on one or
both the remaining necks. The gasses will only go to where they can escape to atmospheric pressure the easiest. Here are a few for sale on ebay
currently
http://shop.ebay.com/i.html?_from=R40&_trksid=p5197.m570...
I have a fancy spinning band distillation column that has the spin shaft run through the reflux condenser on top. But this is a custon piece and very
costly.
|
Ah yes I see, and what would be the use of running water through them (because they seem to have connectors for this)? Or do they just have other uses
except stir bearing too.
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
| Quote: Originally posted by Ophidean |
Ah yes I see, and what would be the use of running water through them (because they seem to have connectors for this)? Or do they just have other uses
except stir bearing too. |
It's for cooling. The bearings can get really hot from the friction, so water cooling is mandatory. Some models use a small reservoir you can fill
with glycerol or paraffin, which serve as a coolant instead of using water.
Just run some tubing from the condenser to the bearing.
| Quote: Originally posted by darel | I have a fancy spinning band distillation column that has the spin shaft run through the reflux condenser on top. But this is a custon piece and very
costly.
|
Pictures, please!
This just in: 95,5 % of the world population lives outside the USA
Please drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
Ophidean
Harmless
Posts: 5
Registered: 8-6-2011
Member Is Offline
Mood: No Mood
|
|
Ok thanks! And last question, what kind of overhead stirring would I have to purchase for this, ive seen some on ebay, but they seem so small, are
they powerfull enough for a 12L flask?
|
|
|
Lambda-Eyde
National Hazard
Posts: 860
Registered: 20-11-2008
Location: Norway
Member Is Offline
Mood: Cleaved
|
|
Buy one with a blade that fits in the flask (and through the joint), and most importantly, with a bar that will fit through your bearing.
This just in: 95,5 % of the world population lives outside the USA
Please drop by our IRC channel: #sciencemadness @ irc.efnet.org
|
|
|
Ophidean
Harmless
Posts: 5
Registered: 8-6-2011
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Lambda-Eyde | | Buy one with a blade that fits in the flask (and through the joint), and most importantly, with a bar that will fit through your bearing.
|
Of course, but I meant like, if you have a 12L flask, filled for like 6-8L. What kind of overhead stirrer would you take? (I meant in power of
course. 40W, 60W, 100W?)
[Edited on 9-6-2011 by Ophidean]
|
|
|
darel
Harmless
Posts: 27
Registered: 12-7-2008
Member Is Offline
Mood: No Mood
|
|
Spinning Band Distillation Column
I believe this is what I got
http://www.brinstrument.com/fractional-distillation/fraction...
It would be the first one
I am still lookng for the interface and software to use the thing. Ebay has a few different types and can't figure out which one is correct. Also need
an adapter to go from a $50/30 spherical to 24/40, 29/42 or 45/50. Ebay has given no such luck and I'm still waiting on a response from the company
for hard/software. Here is a link to the thing disassembled and some of the parts.
http://s287.photobucket.com/albums/ll149/darelgreen/Spinning...
[Edited on 6-9-2011 by darel]
|
|
|
albqbrian
Hazard to Self
Posts: 73
Registered: 26-5-2011
Member Is Offline
Mood: Alternatingly paranoid or pi**ed
|
|
Or...
Just get a cheap electric drill and use the attachment for stirring paint.
|
|
|
Dr.Bob
International Hazard
Posts: 2753
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: Mildly disgruntled scientist
|
|
If you are looking for the actual teflon paddles and stirring rods and bearing shafts, I have a few sets of them for glass flasks, in 24/40 and
several larger sizes. The 24/40 is not much use, as the paddles that fit through that are not big enough to do much stirring, so most people use
larger ones.
A great place to see what is available for labware is the Chemglass.com website, they have their entire catalog on the web, with photos and
descriptions, so you can find a part number or name for what you want along with similar items that might also work. For example, the one below is
for a nice overhead stirrer system. I don't have any stirrer motors left, but have the glass shafts, bearings and paddles left.
Bob
http://www.chemglass.com/product_view.asp?pnr=CG-2039-A-10
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
