Freddybaby
Harmless
Posts: 4
Registered: 8-3-2011
Member Is Offline
Mood: No Mood
|
|
Zinc sulfide thin films on glass
Trying to deposit very thin films of ZnS on glass for gamma detector. This stuff does not mix well with much on my shelf.
Thought about combining with Sylgard silicone elastomere, similar to Sol gel but it's expensive and my needs are small.
Anyone have any ideas ??
Also, I wonder how much the microscope slide will attenuate the light level ? Perhaps a glass coverslip instead
[Edited on 19-3-2011 by Freddybaby]
|
|
|
redox
Hazard to Others
Posts: 268
Registered: 22-2-2011
Location: The Land of Milk and Honey
Member Is Offline
Mood: Chalcogenetic
|
|
Does the zinc sulfide have to be strongly adhered to the glass surface? Or can it be loose?
|
|
|
Freddybaby
Harmless
Posts: 4
Registered: 8-3-2011
Member Is Offline
Mood: No Mood
|
|
It should be bonded to the glass but even simple adhesion would be fine. A photo sensor will be on the opposite side and the entire assem bonded
together.
The ZnS should be fairly protected I guess, it will be exposed to the atmosphere but the coating over the sulfide must be thin for sensitivity.
|
|
|
Ozone
International Hazard
Posts: 1269
Registered: 28-7-2005
Location: Good Olde USA
Member Is Offline
Mood: Integrated
|
|
"..must be thin for sensitivity."
Not so for gammas! A glass slide over the one with the ZnS secured with rubber bands would be fine, and would demonstrate little to no decrease in
counting efficiency (aside from the fact the ZnS is a pretty crummy scintillator). You want the material to be even, but not so thick that your
detector (photodiode, PMT, etc.) cannot see the pulses from the active side. Also, look up ZnS(Ag) (doped with Ag) which is a much more efficient
material.
Cheers,
O3
-Anyone who never made a mistake never tried anything new.
--Albert Einstein
|
|
|
unionised
International Hazard
Posts: 5126
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
Would something like this help?
http://resources.metapress.com/pdf-preview.axd?code=q3655543...
|
|
|
White Yeti
National Hazard
Posts: 816
Registered: 20-7-2011
Location: Asperger's spectrum
Member Is Offline
Mood: delocalized
|
|
Do you have a furnace?
Zinc sulphide sublimes at ~1100C, you could deposit it onto a glass surface by heating some zinc sulphide under a piece of glass. The added bonus to
this method is that any impurities are left behind or evaporated away under the intense heat. Alternatively, if you already have high purity zinc
sulphide, you could melt some glass and mix some of it in, stir, extrude into a sheet and let cool.
|
|
|
Wizzard
Hazard to Others
Posts: 337
Registered: 22-3-2010
Member Is Offline
Mood: No Mood
|
|
Ungh, I don't know what happen to my last post... Apparently it was never sent.
I second the ZnS sublimation idea.
Encase a Ta/Moly boat in a small brick box, sealed with some clay. Fill with argon (recommended?), loosely seal the top with some material. Short some
volts across the with some carbon terminals. Heat to red hot, replace the atmosphere (getting rid of zinc and sulfur), place your glass close above
the boat, forming a loose seal over the top, and then heat the boat as hot as it will go.
ZnS melts at 1830*C, I think.
|
|
|
redox
Hazard to Others
Posts: 268
Registered: 22-2-2011
Location: The Land of Milk and Honey
Member Is Offline
Mood: Chalcogenetic
|
|
How about sandwiching the powder in between two planes of glass, like microscope slides? I'm not very learned in nuclear chemistry (I prefer to stick
to organic), but would the extra sheet of glass interfere with readings?
Just a thought.
My quite small but growing Youtube Channel: http://www.youtube.com/user/RealChemLabs
Newest video: Synthesis of Chloroform
The difference between chemists and chemical engineers: Chemists use test tubes, chemical engineers use buckets. |
|
|
White Yeti
National Hazard
Posts: 816
Registered: 20-7-2011
Location: Asperger's spectrum
Member Is Offline
Mood: delocalized
|
|
Redox:
Yes it would. Beta rays don't make it though a millimetre of aluminium and alpha rays are even easier to stop. The only way to get readings is to have
a thin film of scintillator attached to a glass substrate, or to somehow embed the scintillator inside a very thin piece of glass.
Good thinking though.
|
|
|
redox
Hazard to Others
Posts: 268
Registered: 22-2-2011
Location: The Land of Milk and Honey
Member Is Offline
Mood: Chalcogenetic
|
|
Oh. For some reason I thought this was a scintillator for gamma rays, which, of course, could penetrate.
Whoops!
My quite small but growing Youtube Channel: http://www.youtube.com/user/RealChemLabs
Newest video: Synthesis of Chloroform
The difference between chemists and chemical engineers: Chemists use test tubes, chemical engineers use buckets. |
|
|
White Yeti
National Hazard
Posts: 816
Registered: 20-7-2011
Location: Asperger's spectrum
Member Is Offline
Mood: delocalized
|
|
Gamma rays would penetrate, but they wouldn't interact much with the zinc sulfide. Zinc sulfide, from what I understand, scintillates in the presence
of alpha, beta and X radiation, not gamma. Freddybaby is probably trying to build a scintillation counter, but in order to detect gamma rays
(specifically), different scintillator materials must be used. Besides, the decay of common radioisotopes results in the emission of alpha and beta
particles (gamma radiation is negligible).
So the OP must have misunderstood something. Detecting gamma radiation is not a reliable way to measure radioactivity in rocks/ radium dials/ medical
isotopes etc... Zinc sulfide only allows you to detect alpha and beta particles.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
