Random
International Hazard
Posts: 1120
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
Cinnamaldehyde from cinnamon bark powder
I am thinking about extracting cinnamaldehyde from cinnamon bark powder which can be bought (or maybe the better source is just cinnamon bark?). I
would add MEK based nail polish remover to it to extract it and then I would filter the solution. After that I would leave it to evaporate in the air
(mek should evaporate). Then I would add water and try to extract cinnamaldehyde from water with potassium metabisulphite.
Is this method good or do you have any more suggestions for that?
|
|
bbartlog
International Hazard
Posts: 1139
Registered: 27-8-2009
Location: Unmoored in time
Member Is Offline
Mood: No Mood
|
|
'MEK based nail polish remover... MEK should evaporate...'
And the other stuff in the nail polish remover, what about that? I don't know what constraints you're operating under but acquiring (either buying or
purifying/distilling yourself) some solvent(s) of known composition seems like a good idea. You can't just assume that the other stuff in the nail
polish remover won't screw things up somehow.
Here is one extraction described (uses ether): http://lhs2.lps.org/staff/sputnam/Ent801/lab9.htm
|
|
digitalemu
Harmless
Posts: 38
Registered: 21-10-2010
Member Is Offline
Mood: No Mood
|
|
Fractional distillation under vacuum would be your best bet as you will have your end product in hours, not days. Much less waste, time and effort
that way plus you would end up having to distill anyways after the MEK will extract not only your product but other oils too.
|
|
digitalemu
Harmless
Posts: 38
Registered: 21-10-2010
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by bbartlog | 'MEK based nail polish remover... MEK should evaporate...'
And the other stuff in the nail polish remover, what about that? I don't know what constraints you're operating under but acquiring (either buying or
purifying/distilling yourself) some solvent(s) of known composition seems like a good idea. You can't just assume that the other stuff in the nail
polish remover won't screw things up somehow.
Here is one extraction described (uses ether): http://lhs2.lps.org/staff/sputnam/Ent801/lab9.htm
|
As this page mentions "Purification by flash chromatography", I highly doubt someone who is trying to get MEK from nail polish will have such a setup
available to them, nor the ability to acquire such things like isooctane.
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Is this true cinnamon, or cassia? In the US cassia is labled as cinnamon, in much of the rest of the world doing so is illegal or at least considered
dishonest (if you don't know the flavour difference between cinnamon and cassia, you should learn that).
Within the cassias the Vietnamese or Saigon variety (Cinnamomum loureiroi) has a higher oil content than Chinese cassia or 'cinnamon' (Cinnamomum
aromaticum). True cinnamon (Cinnamomum verum) has less cinnamaldehyde than cassia but more of other flavour components, it is 'sweeter' and has
overtones of orange or other citrus. True cinnammon's bark is thinner that that of the cassias, almost paper-like and easy to crush in your hand; in
the US it can be found in stores catering to folks from Latin America; they know the difference between cassia and cinnamon, unlike the gringos.
Best way to extract is to purchase cassia bark, crush it, and steam distill the oil off. Solvent extract tends to pull out other stuff as well. The
bark is tough, not uncommonly a half cm thick; I crush it in a large rough stone mortar from SE Asia, used for mushing chilies and other plants. You
can find the bark in Asian stores, particularly herb/medicinal stores.
|
|
zed
International Hazard
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
I concur. Try steam distilling it. Nice clean process. Simple equipment.
|
|
digitalemu
Harmless
Posts: 38
Registered: 21-10-2010
Member Is Offline
Mood: No Mood
|
|
Sure, steam distill the bark to get the raw oil, but you will get cinnamon oil and not pure cinnamaldehyde. You still need to perform fractional
distillation to get the pure product.
|
|
arsphenamine
Hazard to Others
Posts: 236
Registered: 12-8-2010
Location: I smell horses, Maryland, USA
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by digitalemu | Sure, steam distill the bark to get the raw oil, but you will get cinnamon oil and not pure cinnamaldehyde. You still need to perform fractional
distillation to get the pure product. | Aldehydes have classically been purified by precipitation of the
bisulfite adduct, filtration and washing of the solid, and regeneration by gentle hydrolysis with bicarbonate or acid as circumstances dictate.
TLC roughly shows you how impure it is. GC exactly shows you, but doing TLC using coffee filter strips is often all you need.
You can purify by vacuum distillation if you need something analytically pure although you lose some product to the pot.
OrgSynth has a good prep for 3-methyl phenylpropanal.
The money shot:
A completely pure sample of the aldehyde is readily obtained by stirring the crude aldehyde with excess saturated aqueous sodium bisulfite
solution for several hours, filtering the solid bisulfite adduct, washing with ether, and liberating the aldehyde with excess aqueous sodium
bicarbonate.
|
|
The WiZard is In
International Hazard
Posts: 1617
Registered: 3-4-2010
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Random | I am thinking about extracting cinnamaldehyde from cinnamon bark powder which can be bought (or maybe the better source is just cinnamon bark?). I
would add MEK based nail polish remover to it to extract it and then I would filter the solution. After that I would leave it to evaporate in the air
(mek should evaporate). Then I would add water and try to extract cinnamaldehyde from water with potassium metabisulphite.
Is this method good or do you have any more suggestions for that? |
Noted in passing by the book owning analogue guy —
JW Purseglove & et al
Spices
Longman
2 vols 813 pages
1981
p. 126. The finest cinnamon bark oil is produced by steam-
or hydro-distillation with cohobation, and Arctander (1960)
recommends that solvent extraction of the distillate is desirable
to obtain the best quality of oil.
The finest cinnamon bark oils are produced from selected
materials (high-grade) cinnamon quills) in the USA and
Western Europe by steam distillation using modern equipment.
English distilled oil contain about 60 per cinnamaldehyde and about
10 per cent eugenol....
...Sri Larkan bark oil 51 to 76 per cent (av 55) aldehyde...
eugenol 5 tom 18 percent...
And other chemicals! See page 135 for a list. [21 chemicals]
Page 140 for Cassia.
I will leave to others — how-to remove the eugenol.
djh
---
Who is looking for —
Cinnamon and Clove, life-savers candy.
[Edited on 6-11-2010 by The WiZard is In]
|
|
Random
International Hazard
Posts: 1120
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
Well, while MEK based nail polish remover has only impurities water, isopropyl alcohol and calcium chloide (and something like methoxyisopropanol -
but it's last on the list so there is maybe a small amount). All that Can be removed after I will solvent extract the oil and evaporate to leave just
the oil by using filter paper and then making adduct of cinnamaldehyde with metabisulphite. Cinnamaldehyde will precipitate and then I just need to
recover it again
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
No -start with a pure solvent, which will still extract additional compounds from the cassia, giving a more complex workup that just steam distilling
the bark. If you use tech grade solvents it is worthwhile to distill them before use. Starting with crappy solvent mixes, in order to extract
complex mixtures, and expecting to easily obtain reasonable pure compounds is generally in the realms frequented by those consuming quantities of
herb on a daily basis.
Also
http://pubs.acs.org/doi/abs/10.1021/jf60182a023
|
|
Random
International Hazard
Posts: 1120
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
The only problem is that I don't have distillation equipment so I have to do it with solvents if I am doing it. I would be happy if it would be even
just 70% pure, maybe I could later purify it more by other means.
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Steam distillation takes little equipment, stainless steel or copper works well for this sort of thing - essential oils from plants. If you use that
ugly source of MEK you'll end up having to steam distill anyway. Get pure MEK, or fractionate the MEK out of the polish remover, or use other pure
solvents such as ethanol, isopropanol, or DCM. If you use tech grade solvents it is worthwhile to distill them before use.
BTW - distillation was one of the earliest processes used by proto-chemists. While borosilicate ground jointed glassware is nice, much distillation
was done with vessels made of other materials although additional care was usually needed to avoid breakage. I've distilled solvents using no more
than milk bottles, corks, soda-lime glass tubing, and a slow cooker as a water bath.
[Edited on 9-11-2010 by not_important]
|
|
Random
International Hazard
Posts: 1120
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
Interesting, thanks for that distillation info. So you used glass milk bottles? I don't have glass tubing, could I use plastic tubing that has water
soaked paper towel around it for condenser? Also I am thinking about light bulbs, is their glass more heat resistant? Those could be interesting flask
(aluminium can be removed with hcl from the light bulb). How dangerous could be distillation in non heat resistant glass? I don't want to be shot with
glass bullets while performing it
[Edited on 9-11-2010 by Random]
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
Plastic tubing generally contains plasticisers, which leach out in organic solvents which thwarts the purpose of distilling. Light bulbs aren't any
better, they are very thin and so withstand thermal stress (fast changes in temperature) better, but are also much more mechanically fragile.
Just don't change the temperature quickly, thus the use of a water bath that is heated after the still pot is placed in it - slow cookers are slow,
takes a log time to get hot enough which is both bad/annoying but also good.
|
|
Random
International Hazard
Posts: 1120
Registered: 7-5-2010
Location: In ur closet
Member Is Offline
Mood: Energetic
|
|
It looks that I should get some copper tubing then, only if I could make some tubing from aluminium foil.. Are there some alternatives to that?
|
|
crystalXclear
Harmless
Posts: 28
Registered: 30-12-2010
Member Is Offline
Mood: No Mood
|
|
As to the glass, I have made and sucsessfully used a thin flurosent light bulb tube within a larger one, cooled by a recycling pond pump. But as
not_important mentioned, they are v-fragile & heat sensative, but great when used with care.
I even used some old heat resistant bricks from a storage heater to create a heat chamber, heated by blow torch to make a verry crude Allihn
condenser,
I first sealed the end of one of the smaller tubes up,
then heated it up at intervals & blew down it creating small bubbles along it's length. v-time consumming & broke three before I mannaged it,
but man did it work well. lots of fun
Stainless steel works great, but I live in a farming comunity, so from old milk parlours to deralict dairy proseessing buisneses, stainless tubeing
and dairy glass are common place here.
I did think about useing that internaly braided clear pipe used on fire extinguishers. It comes in a good range of sizes & has some chemical
resistance. could be worth a try.
I allways wanted to try and use it in combination with the glass.
let me know if you do try it, I would love to here of your results.
Anyone know what the new plastic alternative to copper pipe is like? They should be fine with water and alcohols.
There is a thermal pipe of the above that (MAY) be of some use. proberbly not worth the risk though, plastisisers are more of a problem with
recycled plastic, but are allway's there.
Just a few thaughts. good luck Xtal
|
|
Mailinmypocket
International Hazard
Posts: 1351
Registered: 12-5-2011
Member Is Offline
Mood: No Mood
|
|
I recently attempted to extract some cinnamon oil from about 20 grams of freshly crushed cinnamon sticks, it was a lot of fun and done without soxhlet
extractor. I did a steam distillation followed by extraction with dichloromethane and drying the latter over sodium sulfate. Filtered and distilled
the dry DCM and was left with a small amount of amazing smelling oil. I dont have the exact yield information or procedure handy at the moment but I
can definitely get the info if there is interest
Here is a picture of the final product with a quarter for size comparison.
(Couldnt help myself from tasting the oil on a toothpick, very nice taste... sort of like a cinnamon breath mint without any sweetness!)
[Edited on 24-3-2012 by Mailinmypocket]
|
|
hjhearle
Harmless
Posts: 9
Registered: 24-9-2012
Location: Perthshire, UK
Member Is Offline
Mood:
|
|
Trying to extract cinnamon for my final year school chemistry project usin reduction tube setup. A few problems encountered though.....
1) The product lost its distinctive cinnamon smell and turned a dark brown colour. I have tested for oxidation to cinnamic acid but pH was neutral so
this can't be it. Any ideas? I ditched this sample (perhaps I shouldn't of?)
2) What viscosity should it be? My freshest sample (right colour and smell so far! ) appears somewhat watery even though I removed what water I could by boiling it off and using anhydrous sodium sulphate. About 3.5ml of
it so far.
3) Once I extract a suitable amount I'm going to test its purity with TLC against a known pure sample and react it with 2,4-dinitrophenylhydrazine.
What is the definite melting point of the hydrazone and the accepted IUPAC name? I've tried looking this up but results are not concurrent it says
246,255,262 etc.....
Please help! I'll try to upload some photos.....
HH
|
|