thereelstory!
Harmless
Posts: 2
Registered: 18-9-2010
Member Is Offline
Mood: No Mood
|
|
ground glass joint help
i had a hno3 setup that i left sitting in my fumehood for a few months attached. i have had hell getting the joints seperated. any suggestions on how
to get them unattached?
other than hot cold contrast.
|
|
|
mnick12
Hazard to Others
Posts: 404
Registered: 30-12-2009
Location: In the lab w/ Dr. Evil
Member Is Offline
Mood: devious
|
|
I know this is not what you asked for, but it has always worked in my experience.
Well I had a similar problem once. I have found through trial and error the best method for separating these joints is to first submerge the whole
thing in water then boil for an hour. If this does not work simply allow the the glassware to cool to rt then place the whole thing in the freezer for
a few hours, as the glass cools it shrinks and whatever is stuck pops out (literally).
Hope that helps.
|
|
|
Eclectic
National Hazard
Posts: 899
Registered: 14-11-2004
Member Is Offline
Mood: Obsessive
|
|
Ultrasonic cleaner and a solvent?
|
|
|
Panache
International Hazard
Posts: 1290
Registered: 18-10-2007
Member Is Offline
Mood: Instead of being my deliverance, she had a resemblance to a Kat named Frankenstein
|
|
smash it into several pieces and use pliers and a screwdriver, quickest way for sure.
|
|
|
Mildronate
Hazard to Others
Posts: 428
Registered: 12-9-2009
Member Is Offline
Mood: Ruido sintetico
|
|
http://www.sciencemadness.org/talk/viewthread.php?tid=14343#...
|
|
|
Chainhit222
Hazard to Others
Posts: 138
Registered: 22-8-2009
Location: peach's mailbox
Member Is Offline
Mood: grignard failing to start
|
|
When my joints stuck up after atmospheric distillation of sulfuric acid, i just hit that shit with a blow torch for a while and twisted using a pair
of welders gloves, they came apart fine 
The practice of storing bottles of milk or beer in laboratory refrigerators is to be strongly condemned encouraged
-Vogels Textbook of Practical Organic Chemistry
|
|
|
peach
Bon Vivant
Posts: 1428
Registered: 14-11-2008
Member Is Offline
Mood: No Mood
|
|
Chainhit to the rescue with the simple solution. 
You could try soaking them in water for a day or so. The less you mess around with jammed tapers, and let them soak (in verious things) and fix
themselves, the less likely a broken bit of glass is.
Freeing up stuck tapers can take ages as the things you're using gets through the microscope gap, I spent three weeks plus on one and
still didn't manage. Sometimes a long soak in a bucket of water is enough. If you've had it there for three months, you can afford to wait a few days
more. If not, lesson learned. 
[Edited on 22-9-2010 by peach]
|
|
|
SWilkin676
Hazard to Self
Posts: 68
Registered: 3-2-2010
Member Is Offline
Mood: No Mood
|
|
https://www.pai-net.com/secure/catalog.aspx?ParentKey=10054&...
aerochem's dry teflon spray has saved more than a couple of things around here.
I had a stuck stopcock in a sep funnel that wasn't budging after soaking or hot water. I sprayed some of the aerochem in and it came right out.
I also had two stainless steel sinks stuck together for 6 months and finally got them apart using the aerochem.
|
|
|
peach
Bon Vivant
Posts: 1428
Registered: 14-11-2008
Member Is Offline
Mood: No Mood
|
|
Makes me wonder if stuff like WD40 might save some joints.
As some of you probably know, it wasn't originally designed so much as a lubricant. WD stands for Water Displacing, it was for the Navy to spray into
capillary style joints to get the water out.
I think the primary, very low percentage, component is kerosene, or something similar. I would imagine that may react with some crap stuck between
tapers, and may free them. It may also make things worse if it forms an harder to dissolve tar / solid.
|
|
|
mycotheologist
Hazard to Others
Posts: 154
Registered: 16-3-2012
Member Is Offline
Mood: No Mood
|
|
I forgot to grease up a glass stopper and now its jammed in the RB flasks neck. There was a bit of Ca(ClO)2 inside the neck (because I added it
through the neck but didn't do a very good job of cleaning it out before putting in the stopper) which I believe is what caused the stopper to get
jammed somehow. I'm gonna try submerging the flask in boiling water and see how that goes.
|
|
|
Pyro
International Hazard
Posts: 1305
Registered: 6-4-2012
Location: Gent, Belgium
Member Is Offline
Mood: No Mood
|
|
i find the easiest is to put hot water in the flask, fill it to the top, then run cold water over the other part, all my stuck joints have popped
loose like that.
otherwise you could take it to a glassblower
but of course the best solution to your problem is to not leave it sitting there for so long, take it apart as soon as you can. prevention is better
than cure
[Edited on 12-5-2012 by Pyro]
all above information is intellectual property of Pyro.  |
|
|
sargent1015
Hazard to Others
Posts: 315
Registered: 30-4-2012
Location: WI
Member Is Offline
Mood: Relaxed
|
|
Hmmmm...
Quote: Originally posted by Pyro  |
but of course the best solution to your problem is to not leave it sitting there for so long, take it apart as soon as you can. prevention is better
than cure
[Edited on 12-5-2012 by Pyro] |
I agree with Pyro, don't leave it set up! Does this mean you just left the Nitric acid to react and forgot about it? I'd be more careful/attentive
next time.
But, I digress. My preferred way, along with many other Chemists, is to heat the joint up with a heat gun (Hair dryer if you want) and tap the piece
out with something that will not chip the glass but still provide a good whack.
|
|
|
Vargouille
Hazard to Others
Posts: 380
Registered: 16-4-2012
Member Is Offline
Mood: No Mood
|
|
I heard something a while back about letting it soak in club soda and heating the joint lightly. Should work fairly well.
|
|
|
kuro96inlaila
Hazard to Self
Posts: 96
Registered: 21-6-2010
Location: Malaysia
Member Is Offline
Mood: Quietly thinking
|
|
Boil some water in a kettle,when it boils,pour it slowly on the join.Then twist the two parts strongly but gently and slowly.It always work for
me.
|
|
|
Fantasma4500
International Hazard
Posts: 1681
Registered: 12-12-2012
Location: Dysrope (aka europe)
Member Is Offline
Mood: dangerously practical
|
|
as chainhit222 said, heat it up with a blowtorch, works wonders.. was just about to order new 29/32 500mL flat RBF and 29/32 distillation bridge
distilling phenol without tightening the whole thing properly, followed by not washing it and then trying to distill chloroform was practically
welding the whole thing shut, noticed the ground glass part turned very white, supposing i managed to decompose whatever was keeping it together
|
|
|
subsecret
Hazard to Others
Posts: 424
Registered: 8-6-2013
Location: NW SC, USA
Member Is Offline
Mood: Human Sadness - Julian Casablancas & the Voidz
|
|
I distilled nitric acid a few days ago, and I took the apparatus apart immediately afterward, and I found a stuck joint.
Fear is what you get when caution wasn't enough.
|
|
|
MrBlank1
Hazard to Self
Posts: 96
Registered: 5-2-2013
Location: Oz
Member Is Offline
Mood: Inadvertantly aloof?
|
|
I used this technique often with good success, minus gloves (unwisely):
1) Wear a good thick pair of gloves, use oil (I used olive) by drizzling on inner rim of outer joint, then by using thumb and fore finger, try to
gently but firmly rock top piece, containing inner joint, back and forward a dozen times or so.
2) Rotate 90 degrees and repeat 1.
Whilst doing the above, look at the joint, to see if you can see "bubbles/air cracks" appear and disappear with alternating applications of pressure.
These are a sign that the joint may come free (eventually)
It may take MANY minutes to get this to work. I can't remember where I read this info, but I know the oil part comes from freeing a glass stopper from
a brandy "big ornamental bottle". I suspect it comes from Gary S Coyne's "The Lab Companion", which was my go to lab manual. Being an amateur,
probably more appropriate than Vogel's, I believe.
I have used this technique with success many times. Success rate is very high, excluding sep funnels. Success with sep funnels is maybe just over 50%
for an impatient person like me. I had probably 4 or 5 (250-500mL) broken in 4 years, usually from leaving a HCl generator flushed and joined for 3-4
weeks. Very bad form, I know.
But, if you're not breaking ANY glass in the lab, are you really even using it at all? (<--- meant to be humor)
AAAAA = Australian Association Against Acronym Abuse
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
