oxygen1600
Harmless
Posts: 1
Registered: 28-5-2010
Member Is Offline
Mood: No Mood
|
|
nitroalkane synthesis
There have been some ongoing discussions in this website regarding the synthesis of various nitroalkanes. I happened to come across one publication,
which gives a simple and relatively mild method for preparing various nitroalkanes using polymer assisted nitrites. Ive attached the pdf of this
publication for those who are interested. If anyone has performed this reaction please share your experience.
Attachment: nitroalkane_polysynth.pdf (57kB) This file has been downloaded 928 times
|
|
stateofhack
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 123
Registered: 6-5-2008
Location: Warm Coast
Member Is Offline
Mood: annoyed
|
|
Old.....
|
|
Paddywhacker
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 478
Registered: 28-2-2009
Member Is Offline
Mood: No Mood
|
|
Yes, this has been seen before. But obviously not everybody knows about it, and it is an interesting paper, well within the abilities of amateurs, so
bringing it to our attention again is appreciated.
The PVP polymer is widely used in industry, and ethyl iodide can be prepared by methods detailed in the prepublications forum, so making the
quaternary PVP should be within the scope of any of us.
The nice thing about the polymer it is that that it can be recovered and regenerated.
When I first read this paper I wondered if a conventional anion exchange resin could be used instead of the quat. PVP, but I have not had the
inclination to try it out. Maybe someone here could do that and let us know.
Solid-supported reagents are not just interesting subject, academically .... they lend themselves to very simple workups ... just filter off the
resin.
|
|
Anders Hoveland
Banned
Posts: 208
Registered: 15-6-2010
Member Is Offline
Mood: No Mood
|
|
If anyone can provide a simple rough synthesis for a reaction involving making a nitrite substrate, and also a demonstrating reaction with the
substrate, it would be appreciated. I would like an alternative to AgNO2, AgNO3, and AgClO4 precipitation reactions. In otherwords, can someone
translate that paper into simple English and write a 2 Paragraph summary?
|
|
peach
Bon Vivant
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1428
Registered: 14-11-2008
Member Is Offline
Mood: No Mood
|
|
I think you'll get some replies to that in English, but probably not very polite ones. ![:P](./images/smilies/tongue.gif)
PVP is used for iodine scrub solutions in hospitals. I had a massive container of it from BASF at one point and was using it to get washed with. Germ
free and a fake tan!
|
|
AndersHoveland
Hazard to Other Members, due to repeated speculation and posting of untested highly dangerous procedures!
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1986
Registered: 2-3-2011
Member Is Offline
Mood: No Mood
|
|
It is not completely impossible to directly nitrate alkanes into nitroalkanes at room temperature, the trick is to use a nitronium salt, not mixed
acids:
http://www.pnas.org/content/94/22/11783.full
The vapor phase nitration of propane with nitric acid at 420degC produces various nitroalkanes in 40% yield.
The yield for nitromethane is only 4%, for nitroethane 10%, for 2-Nitropropane the yield is 16%.
The various nitroalkanes are then separated by distillation. Nitomethane boils off first at 101degC, then nitroethane at 114degC. 2-Nitropropane boils
at 120degC. 1-Nitropropane boils at 131degC. 2-Nitropropane is a carcinogen, breathing of its vapor should be avoided. The vapor-phase nitration can
alternatively be done with nitrogen dioxide, giving better yields.
[Edited on 20-4-2011 by AndersHoveland]
|
|
spirocycle
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 197
Registered: 29-9-2010
Member Is Offline
Mood: No Mood
|
|
^werent you banned?
|
|
Waffles SS
Fighter
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 998
Registered: 7-12-2009
Member Is Offline
|
|
Pvp isnt cheap polymer
Aldrich Pvp is 130$ per 10 gr(100-200 mesh, extent of labeling: ~6.5 mmol/g Cl resin loading, 2 % cross-linked with divinylbenzene)
Fluka Pvp is 143 per 50 gr
I think ethyl sulfate method is cheaper and easier.
If anyone know cheaper price please let us know
[Edited on 22-4-2011 by Waffles SS]
|
|
UKnowNotWatUDo
Hazard to Self
![*](images/xpblue/star.gif)
Posts: 96
Registered: 30-6-2010
Member Is Offline
Mood: No Mood
|
|
Isn't Anders always banned?
|
|