Douchermann
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 117
Registered: 11-10-2005
Location: Illinois, USA
Member Is Offline
Mood: No Mood
|
|
How hot is a rotary-vane vacuum pump supposed to get?
After running a single stage vacuum pump at roughly half vacuum (controlled by a home brew regulator) the action side of the pump is quite hot to the
touch. The motor cooling fins however are just barely warm. I'm just curious how hot they're supposed to get, and if/when I should be concerned,
because at the moment, it's the most expensive single lab component I own.
It\'s better to be pissed off than to be pissed on.
|
|
franklyn
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3026
Registered: 30-5-2006
Location: Da Big Apple
Member Is Offline
Mood: No Mood
|
|
Odd, a vane pump set to compression one expects would run hot, not one
set to evacuate air, although once you have vacuum there is no air to cool
it internally so the heat generated by seal friction will be felt externally.
Check the manual specifications specifically for maintenace and lubrication.
Also use a valve to close off your vacuum once you have it, don't run the
thing constantly that may be beyond its duty cycle. Also be certain the
pump material is not corroded by whatever vapor is being vacuumed.
.
|
|
garage chemist
chemical wizard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1803
Registered: 16-8-2004
Location: Germany
Member Is Offline
Mood: No Mood
|
|
My organic chemistry book says that rotary vane pumps are supposed to get hot (80°C), it even is good for them as it keeps vapors and moisture from
condensing into the oil, prolonging its useful life.
|
|
VTchem
Harmless
Posts: 11
Registered: 19-4-2008
Location: Eastern USA
Member Is Offline
Mood: Anticipatory
|
|
We have 2 rotary vane pumps at home and they get warm, I wouldn't say HOT but then again I don't really touch them that often while they are running
so take that with a grain of salt. I would say as long as you aren't burning any oil you should be in the safe zone, but looking into the specs of
your particular machine is the safest way to go.
Go Hokies! \"If it goes \'BOOM\' I like it!\" -Me
|
|
chemrox
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
Mine get to around 80*. They don't pull max vac until warm. Too hot to touch would, to me, indicate too much friction. Bad springs or rotors ..
whatever keeps the vanes against the cylinder walls. Maybe wrong oil or decomposed-contaminated oil. Try a flushing oil for 15 minutes to an hour
and then drain and fill with good oil. Always use high quality vacuum pump oil and nothing else.
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
MadHatter
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 1333
Registered: 9-7-2004
Location: Maine
Member Is Offline
Mood: Enjoying retirement
|
|
Rotary Vane
Interesting, my oiless system doesn't get hot unless I run it for several hours. Sounds like a friction problem to me.
From opening of NCIS New Orleans - It goes a BOOM ! BOOM ! BOOM ! MUHAHAHAHAHAHAHA !
|
|
Douchermann
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 117
Registered: 11-10-2005
Location: Illinois, USA
Member Is Offline
Mood: No Mood
|
|
The oil isn't smoking, and it is high quality vacuum oil. It pulls great vacuum (boils water at 13C, possibly lower). I recently flushed it, and
this oil is nice and clean. The manual it came with was something closer resembling a napkin with some scribbles on it. There was no important
information on there except the drain/flush process which is or should be, common sense. For those curious, it was the single stage rotary vane from
www.cynmar.com (the cheap one). Thanks for your help, It seems lower than 80C so we should be good.
[Edited on 26-4-2008 by Douchermann]
It\'s better to be pissed off than to be pissed on.
|
|