| Pages:
1
2
3
4 |
jpsmith123
National Hazard
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
Forget everything else, diamond is the answer!
According to the attached review paper, doped diamond electrodes may replace MMO, platinum and PbO2.
The paper doesn't explicitly mention suitability for perchlorate production, but it's clearly implied I would say.
Also, U.S. patent app. #20070170070 claims the use of a doped diamond coated anode to make perchloric acid.
Being that graphite can apparently be used as a substrate for diamond deposition, and being that "diamond-like" films can be electrolytically
deposited from methanol...this gets me thinking...I wonder if trimethyl borate could be added to the methanol to dope the product with boron?
Attachment: Doped Diamond Electrodes.pdf (804kB)
This file has been downloaded 1617 times
|
|
|
Xenoid
National Hazard
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
Hmmm..... Now all we have to do is erect aerials on our roofs, and wait for a thunderstorm....
http://www.sciencemadness.org/talk/viewthread.php?tid=8629&a...
May be we should all try Bob's method after all .... 
http://members.tm.net/lapointe/Allotropes.html
[Edited on 13-12-2007 by Xenoid]
|
|
|
JohnWW
International Hazard
Posts: 2849
Registered: 27-7-2004
Location: New Zealand
Member Is Offline
Mood: No Mood
|
|
The only problem is that diamond is a very good insulator, in fact one of the best. "Doping" it with small amounts of N or B, incorporated into
artificial diamonds, which is a very expensive thing to do, has been done to make semiconductors (n and p type respectively), which operate at
voltages about 5 times that for Si or Ge based semiconductors, although because of their cost they are still largely experimental.
|
|
|
I am a fish
undersea enforcer
Posts: 600
Registered: 16-1-2003
Location: Bath, United Kingdom
Member Is Offline
Mood: Ichthyoidal
|
|
Actually, not doping synthetic diamond with nitrogen is the difficult bit. Diamonds produced by Gemesis are yellow in colour due to nitrogen impurities. Avoiding this contamination is a major technical challenge.
1f `/0u (4|\\| |234d 7|-|15, `/0u |234||`/ |\\|33d 70 937 0u7 /\\/\\0|23.
|
|
|
12AX7
Post Harlot
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
Odd, I heard that they produce N-doped diamonds because they are more expensive.
Edit: The wiki article implies that a vacuum chamber may be all that is needed. Exclude N2, maybe introduce BH3, etc. as desired. (For that matter,
B dissolves in Fe. Even easier.)
Tim
[Edited on 12-14-2007 by 12AX7]
|
|
|
I am a fish
undersea enforcer
Posts: 600
Registered: 16-1-2003
Location: Bath, United Kingdom
Member Is Offline
Mood: Ichthyoidal
|
|
The impure nitrogen-doped diamonds sell for more, because that is how the gem market is stacked, with coloured gems attracting higher prices.
However, technically speaking, the nitrogen doping is a flaw in the process.
1f `/0u (4|\\| |234d 7|-|15, `/0u |234||`/ |\\|33d 70 937 0u7 /\\/\\0|23.
|
|
|
dann2
International Hazard
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
Hello,
I am no diamond expert but I will come in with my 2c's worth. (pun intended).
I think the N doped one sell for more if they are naturally occuring only. If made in the lab (N doped or otherwise) they sell for less.
Lab make diamonds can be told apart from naturally occuring ones by a lab test. Don't think you can tell them apart (the good one's anyways) from
visual inspection.
One last gem of info:
Diamond has one of the highest thermal conductivity off all substances. It conducts heat by some weird and wonderful 'lattice vibrations'.
Dann2
|
|
|
Xenoid
National Hazard
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
Synthetic diamonds made by the latest techniques are readily distinguished from natural stones by optical microscopic examination, they are FLAWLESS.
Natural stones have all sorts of lattice defects and occluded minerals.
I am still waiting for the diamond coated frying pans, which were touted about, several years ago...
|
|
|
12AX7
Post Harlot
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
It also has an anomalous heat capacity, something Einstein and Debye theorized on early in the 20th century. The best explanation is a lattice of
relatively stiff oscillators, linked to each other such that one can analyze the exchange of energy as wave particles -- phonons -- bouncing around
inside, having energies from about zero up to a cutoff, such that the wavelength of these oscillations must be less than the corresponding distance
between atoms.
Diamond is composed of a rather stiff lattice; as a result, these oscillators have steep energy levels and don't store much energy (as heat) at low
temperatures. As a result, diamond has significantly less heat capacity than most other materials at room temperature.
Statistical mechanics is interesting, if mathematically intensive. I now know the formulas and derivations explaining this, though it's certainly
above and beyond the topic of this thread (and probably of even less interest to most here!).
Tim
|
|
|
chloric1
International Hazard
Posts: 1147
Registered: 8-10-2003
Location: GroupVII of the periodic table
Member Is Offline
Mood: Stoichiometrically Balanced
|
|
We only need a plasma at 2200 to 2800. Comeon it is not that hard to do in the garage.
Seriousy though, microwave energy was mentioned and someone that reads here who has telecommunication expertice might be able to make a microwave gun
that can be tuned to energize some organic vapors. Microwaves are definately able to heat certain things up to insane temperatures in a hurry.
Silicon as a substrate? Wow! That's just crazy cool! Of coarse not practical for large electrodes but it would nice for a pocket model. I would
like to known in my neighborhood as"The guy who makes doped diamond silicon substrate anodes" I wonder how well they could sell on ebay.
Fellow molecular manipulator
|
|
|
Twospoons
International Hazard
Posts: 1326
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
Of the diamond CVD papers I've seen, the most common (and accessible for us) method is simply a hot tungsten filament in a low pressure atmosphere of
H2, CH4, CO2. Even the pressure requirements are not difficult ( 1or 2 torr IIRC). Typical substrates were tungsten sheet rubbed with diamond dust
(for nucleation). Deposition rates are slow - μm per hour - so it would likely take a week or two to build a working coat.
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
jpsmith123
National Hazard
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
I've seen a patent claiming that you can use water/alcohol vapor instead of H2 & CH4.
But anyone with a high voltage DC power supply can try the electrolysis of methanol as per the attached paper.
Attachment: Electrolysis of Methanol.pdf (132kB)
This file has been downloaded 1997 times
|
|
|
Nixie
Hazard to Others
Posts: 490
Registered: 12-12-2006
Member Is Offline
Mood: ?
|
|
| Quote: | Originally posted by jpsmith123
I've seen a patent claiming that you can use water/alcohol vapor instead of H2 & CH4.
But anyone with a high voltage DC power supply can try the electrolysis of methanol as per the attached paper. |
I wonder if there's any benefit to going for a higher voltage (I can do about 150 kV at the suggested 20 mA current density), at least in terms of
being able to deposit a thicker film. The only thing I'm missing to try that experiment is the HF for cleaning the substrate (and I have no clue how
to obtain any). And how would one go about doping such a film?
[Edit:] By the way, I'm still waiting for you to answer my message from a long time ago :|
[Edited on 17-12-2007 by Nixie]
\"Good is a product of the ethical and spiritual artistry of individuals; it cannot be mass-produced.\" --Aldous Huxley
|
|
|
jpsmith123
National Hazard
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
I'd bet that you could use a graphite substrate with the surface prepared by anodic etching in NaOH, Na2CO3, Na3PO4, etc. Maybe electrocleaned and
hydrided titanium would work, too.
IMO, one interesting experimental aspect would be to see if the coatings could be made conductive by adding small amounts of, say, methyl borate or
some other boron containing compound to the methanol.
(BTW sorry about the lapse. I was forced to move a few times, unexpectedly, and I had little or no internet access and no access to my files, etc.,
for a few months. Are you still involveed with that project?)
|
|
|
Nixie
Hazard to Others
Posts: 490
Registered: 12-12-2006
Member Is Offline
Mood: ?
|
|
I am; not in a hurry as work is busy at the moment, but I hope to get back to it early '08. It'd help if I knew what else I'd need to purchase so I
watch out on eBay and surplus places.
\"Good is a product of the ethical and spiritual artistry of individuals; it cannot be mass-produced.\" --Aldous Huxley
|
|
|
jpsmith123
National Hazard
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
I'm still thinking about this, especially since none of other efforts have yet produced a reliable perchlorate anode.
Ok here's the idea:
It seems that many places are selling diamond powder on line...I've seen it for a few dollars per gram. I would guess that at least some of these
powders are "contaminated" with something else e.g. nitrogen, and are therefore conductive.
In several of his patents Beer talks about "rolling" the noble metal oxide into the titanium, or electrophoretic deposition, or just painting on an
oxide slurry, followed by baking at high temperature.
According to several patents, titanium hydride can be used to create a bond to diamond; just mix the hydride with diamond and heat to decompose the
hydride (preferably in an inert or a reducing atmosphere).
So why not take a piece of Ti, hydride it, coat it with diamond powder, and bake to create the bond?
[Edited on by jpsmith123]
|
|
|
-jeffB
Hazard to Others
Posts: 185
Registered: 6-12-2007
Member Is Offline
Mood: No Mood
|
|
If electrolyzing methanol at kilovolts is annoying, what about DMSO at 150V?
http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=n...
|
|
|
-jeffB
Hazard to Others
Posts: 185
Registered: 6-12-2007
Member Is Offline
Mood: No Mood
|
|
| Quote: | Originally posted by Xenoid
I am still waiting for the diamond coated frying pans, which were touted about, several years ago... |
I got to try one of these out some years ago -- a friend of mine ran a materials lab, and one of their collaborators was looking at starting up a
company to make them. It was disappointing. It was a lot stickier than Teflon, or even well-seasoned cast-iron, and it certainly appeared
to be scratched by stainless-steel utensils, although I suppose I may just have been leaving stainless-steel streaks on it. There is something cool,
though, about the idea of serving breakfast out of a diamond skillet...
|
|
|
microcosmicus
Hazard to Others
Posts: 287
Registered: 31-12-2007
Member Is Offline
Mood: spin up
|
|
Assuming you have some sort of furnace which can achieve the required
temperature in an atmosphere which doesn't burn your diamonds, this
sounds like something interesting to try. This is the sort of procedure used
to make diamond files. At any rate, it would be interesting to be able to do
this at home --- I would certainly be curious to know how your attempts turn
out since high temperature stuff interests me.
As for use as an anode, an obvious point is that the substrate holding the
diamond is metal (titanium in this case) and therefore also conducts so,
if your purpose were to create an anode in which the conducting surface
were purely diamond, this would not do. Rather, you would have a mixed
titainium-diamond electrode. Looking at one of my diamond files, I see that
something like half the surface area is metal substrate, To have only the
diamond be in contact with the electrolyte, you would somehow have to
cover the titanium which holds the diamond grains in place with an insulator.
Maybe this could be done by some process like painting the electrode with
an insulator, then rubbing out the high spots so the diamonds show through
or maybe you could cover the Ti with a non-conductive oxide layer by anodizing it.
[Edited on 8-1-2008 by microcosmicus]
|
|
|
jpsmith123
National Hazard
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
@-jeffB: Thanks for the reference. I've posted a request for the full paper.
@microcosmicus: Theoretically it's ok to have titanium exposed to the electrolyte, as it forms a self-protecting oxide layer. (That's why titanium and
the other so-called "valve" metals are preferred as substrate materials).
|
|
|
microcosmicus
Hazard to Others
Posts: 287
Registered: 31-12-2007
Member Is Offline
Mood: spin up
|
|
@jpsmith123
In that case, what about stainless steel --- an oxide coating is what
makes it stainless, after all. Or is titanium oxide more resistant to
the stuff found in chlorate cells than chromium oxide? Diamond in a
SS substrate is quite easy to find in the form of diamond files, laps,
knife sharpeners, etc.
Duh -- using the stuff as an anode would automatically anodize it,
wouldn't it 
[Edited on 8-1-2008 by microcosmicus]
|
|
|
12AX7
Post Harlot
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
I'm learning every day, more and more, just how fucking resilient TiO2 is. Even to fluorides. . .
Stainless does not compare, period.
Tim
|
|
|
jpsmith123
National Hazard
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
Here's another interesting paper.
This paper describes some diamond coated anodes. Note the current densities they tested them at.
"However until now, diamond has not been introduced in electrochemical applications because of the limited availability of diamond for large-area
electrodes. In the last years large-area chemical vapour deposition (CVD) of polycrystalline diamond films has been developed, yielding deposition
areas of up to 0.3 m2 on metallic and ceramic substrates. These boron doped conductive diamond electrodes are semiconductor electrodes with a
microcrystalline structure and comparatively rough surfaces. Diamond-coated electrodes are chemically, mechanically and thermally very resistant (4)
and show no significant corrosion even under high electrochemical load (5, 6). Galvanostatic investigations show no detectable changes of the
electrodes for example after several hours in a solution of NaF in concentrated nitric acid at 50 °C (6) or in sulphuric acid (7). Over several weeks
at 2 to 10 A cm-2 and thousands of Ah cm-2 the electrochemical activity of these diamond electrodes remains also constant in contrast to other
conventional carbon electrodes (8)."
Attachment: Paper.pdf (2MB)
This file has been downloaded 3382 times
|
|
|
Nixie
Hazard to Others
Posts: 490
Registered: 12-12-2006
Member Is Offline
Mood: ?
|
|
What is the maximum temperature diamond can withstand in air for a prolonged period of time? I platinum-plated my tunsten plasma electrodes, but I'm
wondering if diamond would last longer or allow a higher temperature.
[Edited on 8-1-2008 by Nixie]
\"Good is a product of the ethical and spiritual artistry of individuals; it cannot be mass-produced.\" --Aldous Huxley
|
|
|
jpsmith123
National Hazard
Posts: 764
Registered: 24-6-2005
Member Is Offline
Mood: No Mood
|
|
IIRC it starts to oxidize around 700 C or something like that, so you're probably better off with platinum.
What'd you do, electroplate the platinum onto the electrodes?
|
|
|
| Pages:
1
2
3
4 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
