| Pages:
1
2 |
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
iron mess to clean from rb flask
Posting this question here, as not sure where it should go.
After a messy o-toluidine reaction attempt there is a mass of iron chloride that seems to refuse to budge. 3rd day of soaking with hcl and well...its
still happily grunging up the glassware. poking at it loosens it a bit, but will admit to being a lazyass in this as there is a lot of it...
I was thinking of a piranha bath but after reading about it, the stuff worries me. what will its reaction be? violent reaction? explosion? a little
elf appearing to hand me a Darwin award with an evil cackle?
I am considering placing 35%h202 in the flask first, and then add h2so4..this outta clean it out but Id like suggestions first from the more
illuminated types..dilute the h2o2? the h2so4? anyone here clean this mess before?
Thanks
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
No experiance with that particuar reaction, but lots of experiance using pirhanna solution to clean stuff.
The proper method of using pirana is to add the conc. sulfuric first to the mess, and then slowly add cool 30-35% peroxide with stirring/swirling. I
have only ever had one incident with it, and that was when I had lots of organics in the mix, and added the peroxide too fast, and all that happened
was the mix boiling over and making lots of corrosive smoke that horribly oxidized the aluminum test tube rack in the fume hood. I can't imagine how
bad that would have been where there is less than good ventilation...
[Edited on 8-8-2007 by The_Davster]
|
|
|
12AX7
Post Harlot
Posts: 4803
Registered: 8-3-2005
Location: oscillating
Member Is Offline
Mood: informative
|
|
What form is it? Just FeCl3? That's soluble in water, and hydrolysis products like Fe(OH)3 are soluble in HCl. So there must be something about its
structure that's making it hard (embedded in rough surface; in a refractory Fe2O3 form; etc.?). Any description on that matter?
Tim
|
|
|
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
Thanks Dav, I'll give it a try tomorrow.
12AX7, Beats me. I was surprised at the pain its become. Its black, nasty looking and stubborn. Thats all I know for sure.
|
|
|
not_important
International Hazard
Posts: 3873
Registered: 21-7-2006
Member Is Offline
Mood: No Mood
|
|
piranha solution is for organics, if what you have is mostly inorganic then it won't be that much more effective than just the H2SO4.
I'd try 10 to 20 percent HCl, reflux it gently for some time. Note that this concentration is below constant boiling, so it should not have too much
acid vapour coming off.
I assume you were running a reduction, but even in a reduction you can get oxidation if the mix overheats or the reducing agent gets walled off from
the rest of the reactants. So it is possible that you've some good organic gorp gluing things into a lump. But before I went after it with piranha,
I'd do the acid treatment, keep the acid, dry the flask, and reflux kerosene in it - about half full or a little more if that's what it takes to cover
the glorp. Let it cool a bit, pour the hot kerosene into a metal container, rinse the flask with a bit more hot kerosene. After the flask is cold, use
acetone or such to remove the last of the kerosene, let that solvent evaporate, and try refluxing the acid again.
Piranha is sort of the agent of last resort, I even use hot permanganate before goig to piranha when cleaning. As The_Davster said, add the peroxide
slowly, making sure that it's well mixed before adding more.
|
|
|
Twospoons
International Hazard
Posts: 1326
Registered: 26-7-2004
Location: Middle Earth
Member Is Offline
Mood: A trace of hope...
|
|
IIRC iron stains are particularly hard to remove from glass, as the iron penetrates somewhat. You may be able to try this:
http://www.freepatentsonline.com/6297208.html (fluoboric acid)
Helicopter: "helico" -> spiral, "pter" -> with wings
|
|
|
The_Davster
A pnictogen
Posts: 2861
Registered: 18-11-2003
Member Is Offline
Mood: .
|
|
Another gentler alternative to pirhanna, which I have used for iron oxide and manganese oxide stains on glassware is peroxide and HCl. I forgot about
this one in my earlier post, but it is what I prefer to use for removing metal oxides. I usually use it in dilute solution, around 15%HCl with 3%
peroxide added, its is not nearly as risky as pirhanna, and I am sure you could also give diluted sulfuric acid and peroxide a try first. No sense
breaking out the pirhanna for anything but the worst.
|
|
|
Ozone
International Hazard
Posts: 1269
Registered: 28-7-2005
Location: Good Olde USA
Member Is Offline
Mood: Integrated
|
|
Are you sure that the stuff is all iron based (and not, say, some polymeric tar and iron-stuff)? This would make a great deal of difference in how it
behaves with a piranha.
ANy Fe 2+ you have in there will decompose your H2O2, catalytically (this can be a bit frisky yielding -OH , .OH radicals and Fe3+).
I'd try conc. HNO3, heat if necessary, with ventilation. This should oxidize and solvate most of the stuff. You may have a brown stain in your glass
forever, but at least the clumps should go away.
Cheers,
O3
-Anyone who never made a mistake never tried anything new.
--Albert Einstein
|
|
|
woelen
Super Administrator
Posts: 8027
Registered: 20-8-2005
Location: Netherlands
Member Is Offline
Mood: interested
|
|
If I read this, I don't think it is only some inorganic iron stuff. Most likely you have a mix of organics and iron salts. I have been quite
succesfull in cleaning glassware with a mix of 25% HCl and some TCCA or calciumhypochlorite. This makes a strongly acidic chlorine-rich environment,
and such a mix destroys many organics fairly quickly. Some gentle heating may be necessary and occasional adding of some solid TCCA (or better:
calcium hypochlorite) during the process also helps. You need good ventilation though, a lot of chlorine will escape from the bottle.
|
|
|
YT2095
International Hazard
Posts: 1091
Registered: 31-5-2003
Location: Just left of Europe and down a bit.
Member Is Offline
Mood: within Nominal Parameters
|
|
if it`s Just iron, then Oxalic acid works wonders 
\"In a world full of wonders mankind has managed to invent boredom\" - Death
Twinkies don\'t have a shelf life. They have a half-life! -Caine (a friend of mine)
|
|
|
greenyppols
Hazard to Self
Posts: 97
Registered: 17-3-2005
Location: Behind you, watching intently, sexually tense.
Member Is Offline
Mood: Who's been messin' with my moods?
|
|
Wow. Thanks for all the ideas everyone. Im gonna take notes on these and keep 'em around for when needed again.
|
|
|
YT2095
International Hazard
Posts: 1091
Registered: 31-5-2003
Location: Just left of Europe and down a bit.
Member Is Offline
Mood: within Nominal Parameters
|
|
I had bad rust stained jeans the once, so bad it even made holes in places, gut a ball of cotton wool, dip in water and then damp some oxalic acid
powder on, rub the material and the rust vanishes right before your eyes
and now as a result I have my hearing 100% intact as the wife never shouted at me for "ruining" them
\"In a world full of wonders mankind has managed to invent boredom\" - Death
Twinkies don\'t have a shelf life. They have a half-life! -Caine (a friend of mine)
|
|
|
contrived
Hazard to Self
Posts: 56
Registered: 9-3-2007
Location: Washington State
Member Is Offline
Mood: skeptical
|
|
hee hee .. nice bit of realism .. I'm looking for my oxalic as I type
|
|
|
C6H6
Harmless
Posts: 2
Registered: 27-8-2007
Member Is Offline
Mood: Alive
|
|
I'm new to posting, but just if HCl Doesn't work, and the residue might be organic, you could always try an overnight basebath. (IPA, EtOH, or MeOH
saturated with KOH + a bit of H20). It's easy, and not very risky (the Ethoxide and Methoxide can be poisonous by absorbtion, so careful) I would use
90% rubbing alcohol and saturate it with KOH or NaOH and let the glassware soak.
[Edited on 27-8-2007 by C6H6]
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
OK, so I'm digging up an old thread but I wondered if anyone else had come across these? Given the product's name, I wasn't going to us eit as a topic
title.
http://www.cucinadirect.com/go/Product_5265.html
|
|
|
Antwain
Hazard to Others
Posts: 252
Registered: 21-7-2007
Location: Australia
Member Is Offline
Mood: Supersaturated
|
|
How the hell is that supposed to work? Abrasive?
Or snake oil? 
|
|
|
Eclectic
National Hazard
Posts: 899
Registered: 14-11-2004
Member Is Offline
Mood: Obsessive
|
|
If there is a bit of diamond dust embedded in the copper surface, they will abrade away almost any surface. Finer than 8000 grit and you probably
wouldn't even see any scratching on glass.
|
|
|
DJF90
International Hazard
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
One cleaning solution I've heard of before is Caro's acid (sp?) IIRC it's a dichromate salt in dilute sulphuric acid. might be worth a shot...
|
|
|
MagicJigPipe
International Hazard
Posts: 1554
Registered: 19-9-2007
Location: USA
Member Is Offline
Mood: Suspicious
|
|
I would like to add that dilute HF does wonders for rust and other oxides. In case you don't want to make it yourself (don't blame you) they sell a
~2% (I think) solution at Wal-Mart in a brown bottle (Wink-it brand I think). It's the one with all the horrible warnings of death and doom on the
front.
"There must be no barriers to freedom of inquiry ... There is no place for dogma in science. The scientist is free, and must be free to ask any
question, to doubt any assertion, to seek for any evidence, to correct any errors. ... We know that the only way to avoid error is to detect it and
that the only way to detect it is to be free to inquire. And we know that as long as men are free to ask what they must, free to say what they think,
free to think what they will, freedom can never be lost, and science can never regress." -J. Robert Oppenheimer
|
|
|
YT2095
International Hazard
Posts: 1091
Registered: 31-5-2003
Location: Just left of Europe and down a bit.
Member Is Offline
Mood: within Nominal Parameters
|
|
| Quote: | Originally posted by DJF90
One cleaning solution I've heard of before is Caro's acid (sp?) IIRC it's a dichromate salt in dilute sulphuric acid. might be worth a shot...
|
Caros acid is Sulphuric and H2O2 mixed, the one you mention is Chromic acid, often used on glassware to destroy organic matter.
\"In a world full of wonders mankind has managed to invent boredom\" - Death
Twinkies don\'t have a shelf life. They have a half-life! -Caine (a friend of mine)
|
|
|
chloric1
International Hazard
Posts: 1147
Registered: 8-10-2003
Location: GroupVII of the periodic table
Member Is Offline
Mood: Stoichiometrically Balanced
|
|
| Quote: | Originally posted by YT2095
if it`s Just iron, then Oxalic acid works wonders |
That's no joke. I had a porous porcelain morter without glaze and it had iron oxide stain for 8 years! I dissolved oxalic acid in boiling water and
poured this into the dish and walked away for 3 minutes and came back to morter white as new with a yellow solution. It was very hot and sunny where
I did this so any trioxalatoferrate(III) generated was reduced by the abundant UV rays to the yellow ferrous complex.
Fellow molecular manipulator
|
|
|
leu
Hazard to Others
Posts: 368
Registered: 13-10-2005
Member Is Offline
Mood: No Mood
|
|
Aqua regia works very well for cleaning up such problems 
Chemistry is our Covalent Bond
|
|
|
UnintentionalChaos
International Hazard
Posts: 1454
Registered: 9-12-2006
Location: Mars
Member Is Offline
Mood: Nucleophilic
|
|
Sorry to deviate from the original topic but in response to chloric's post above: when I get my unglazed porcelain mortar stained badly and can't seem
to get it out with simple (inexpensive!) chemical means, I throw a scoop of white quartz sand in and just grind until it looks clean again. Works like
a charm.
Department of Redundancy Department - Now with paperwork!
'In organic synthesis, we call decomposition products "crap", however this is not a IUPAC approved nomenclature.' -Nicodem
|
|
|
unionised
International Hazard
Posts: 5128
Registered: 1-11-2003
Location: UK
Member Is Offline
Mood: No Mood
|
|
"How the hell is that supposed to work? Abrasive?
Or snake oil? "
Well Antwain, I haven't tried snake oil but these work just fine. They are based on a very old idea used by buttlers for cleaning decanters by
swilling a mixture of water lead shot and sand round in the bottle to scrub out the stuff.
Presumably this
http://www.rohs.gov.uk/
took out the use of lead shot, but the copper works well enough.
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
| Quote: | Originally posted by The_Davster
No experiance with that particuar reaction, but lots of experiance using pirhanna solution to clean stuff.
The proper method of using pirana is to add the conc. sulfuric first to the mess, and then slowly add cool 30-35% peroxide with stirring/swirling.
|
Could you give us the ratios? And once mixed is it re-useable like chromic solution?
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
|
| Pages:
1
2 |
![[*]](images/xpblue/default_icon.gif){kind=icon}
