Abromination
Hazard to Others
Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline
Mood: 1,4 tar
|
|
Collection of Chlorine by Electrolysis
Everyone knows how to make chlorine by the electrolysis of sodium chloride in solution, but it disolves into the water as HClO and reacts with the
sodium hydroxide also formed to make sodium hypochlorite. How many grams of NaCl per liter of water are required to make excess chlorine that doesn't
react? Better yet, how many g/L are required to make a visible amount? I know I could just add sodium hypochlorite to HCl, but I dont have any HCl and
need something controllable.
List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
-------------- |
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Electrolysis of sodium (and potassium) chloride is done industrially on a very large scale to produce the hydroxide, hydrogen gas, chlorine,
hypochlorite, and chlorate. This is called the chloralkali process.
Now, if you just put some salt water in a beaker and electrolyse it, the sodium hydroxide which is produced will make the solution strongly basic.
Chlorine reacts with the hydroxyl ions and is disproportionated to chloride and hypochlorite:
Cl2 + 2OH- -> Cl- + ClO- + H2O
Since the hydroxide is formed in the exactly the quantity which would be needed to react with the chlorine, there is no amount salt that will be
enough. What you need to do is to keep the hydroxyl ions away from the chlorine. Industrially, ion exchange membranes are used to do this.
Here's what I'd try instead:
Get 2 beakers, and fill one with tap water and the other with a strong solution of sodium chloride. Wet a strip of filter paper with tap water and use
it to bridge between the two beakers. Place one electrode in each beaker and connect the brine side to the positive terminal of your DC power supply
and the water side to the negative.
At the anode, chloride ions are oxidized to chlorine:
2Cl- -> Cl2 + 2e-
And at the cathode, water is reduced to hydrogen and hydroxide:
2H2O + 2e- -> H2 + 2OH-
The sodium ions from the salt pass through the paper bridge towards the cathode, resulting in sodium hydroxide in solution.
[Edited on 9-8-2018 by DavidJR]
|
|
|
Abromination
Hazard to Others
Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline
Mood: 1,4 tar
|
|
Quote: Originally posted by DavidJR  | Electrolysis of sodium (and potassium) chloride is done industrially on a very large scale to produce the hydroxide, hydrogen gas, chlorine,
hypochlorite, and chlorate. This is called the chloralkali process.
Now, if you just put some salt water in a beaker and electrolyse it, the sodium hydroxide which is produced will make the solution strongly basic.
Chlorine reacts with the hydroxyl ions and is disproportionated to chloride and hypochlorite:
Cl2 + 2OH- -> Cl- + ClO- + H2O
Since the hydroxide is formed in the exactly the quantity which would be needed to react with the chlorine, there is no amount salt that will be
enough. What you need to do is to keep the hydroxyl ions away from the chlorine. Industrially, ion exchange membranes are used to do this.
Here's what I'd try instead:
Get 2 beakers, and fill one with tap water and the other with a strong solution of sodium chloride. Wet a strip of filter paper with tap water and use
it to bridge between the two beakers. Place one electrode in each beaker and connect the brine side to the positive terminal of your DC power supply
and the water side to the negative.
At the anode, chloride ions are oxidized to chlorine:
2Cl- -> Cl2 + 2e-
And at the cathode, water is reduced to hydrogen and hydroxide:
2H2O + 2e- -> H2 + 2OH-
The sodium ions from the salt pass through the paper bridge towards the cathode, resulting in sodium hydroxide in solution.
[Edited on 9-8-2018 by DavidJR] |
Haven't tried with a paper bridge yet, have always used a mebrane. And the chlorine will be visible and will not remain in solution? I'm terrible at
electrochemistry.
List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
-------------- |
|
|
Ubya
International Hazard
Posts: 1247
Registered: 23-11-2017
Location: Rome-Italy
Member Is Offline
Mood: I'm a maddo scientisto!!!
|
|
well if you are using an ion exchange membrane use that!
if it's just a mesh membrane it won't work, hydroxyl ions still come in contact with chlorine gas
---------------------------------------------------------------------
feel free to correct my grammar, or any mistakes i make
---------------------------------------------------------------------
|
|
|
MrHomeScientist
International Hazard
Posts: 1806
Registered: 24-10-2010
Location: Flerovium
Member Is Offline
Mood: No Mood
|
|
I've done this with a common clay flower pot as my membrane. My goal was the NaOH, though, so I just let the chlorine escape. Just place a small clay
flower pot inside a larger container, and fill both up with salt water to below the rim of the flower pot. You may need to let it soak for an hour or
so before it becomes conductive. One electrode goes in the outer container, and one in the inner container. In my setup, NaOH was made in the flower
pot and chlorine made at the outer electrode. It's been quite a while so I don't recall all the details, but I believe I used steel rods as
electrodes. You can also use salt water in just one of the chambers and distilled (with a tiny bit of electrolyte) in the other one, but again I don't
recall which is which. Maybe with your recent experience you'll already know what to do!
To collect the chlorine, you could use an outer container with a lid. Make a hole in it and lead the gas through a drying tube into your collection
flask. Chlorine isn't very soluble so you should be fine, but you could always boil the water afterward to drive it out. Whether it's visible or not
would depend on the rate it's made and the final volume, I guess. If you seal it in a long glass tube, it's easier to see (look down the length of the
tube).
|
|
|
Abromination
Hazard to Others
Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline
Mood: 1,4 tar
|
|
Nah, just a PP mesh membrane. Flower pot is a cool idea, but for this I'll just use a salt bridge. Also, while im at this I might as well do something
the the HClO that I make. Could I just leave it out in the sun to decompose to HCl?
List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
-------------- |
|
|
GrayGhost-
Hazard to Self
Posts: 61
Registered: 31-10-2017
Location: Argentina
Member Is Offline
Mood: No Mood
|
|
I used time ago flower pot ( terracotta) like membrane and work, Chlorine dissolve in ClNa solution and when is satured evolve like Cl2 gas.
I used PET bottle cut half like bell for pick up the gas.
My wife use the pot for you flower and that dry .
She say , what make you with this pot man?
nothing nothing .
Possibly was impregnated with Na0H and kill the plant.
|
|
|
Abromination
Hazard to Others
Posts: 432
Registered: 10-7-2018
Location: Alaska
Member Is Offline
Mood: 1,4 tar
|
|
| Quote: Originally posted by GrayGhost- | I used time ago flower pot ( terracotta) like membrane and work, Chlorine dissolve in ClNa solution and when is satured evolve like Cl2 gas.
I used PET bottle cut half like bell for pick up the gas.
My wife use the pot for you flower and that dry .
She say , what make you with this pot man?
nothing nothing .
Possibly was impregnated with Na0H and kill the plant.
|
Same with thermite 
Also, if I add copper oxide to the hypochlorous acid it supposedly will decompose into HCl in solution. I think.
List of materials made by ScienceMadness.org users:
https://docs.google.com/spreadsheets/d/1nmJ8uq-h4IkXPxD5svnT...
--------------------------------
Elements Collected: H, Li, B, C, N, O, Mg, Al, Si, P, S, Fe, Ni, Cu, Zn, Ag, I, Au, Pb, Bi, Am
Last Acquired: B
Next: Na
-------------- |
|
|
GrayGhost-
Hazard to Self
Posts: 61
Registered: 31-10-2017
Location: Argentina
Member Is Offline
Mood: No Mood
|
|
| Quote: Originally posted by Abromination | | Quote: Originally posted by GrayGhost- | I used time ago flower pot ( terracotta) like membrane and work, Chlorine dissolve in ClNa solution and when is satured evolve like Cl2 gas.
I used PET bottle cut half like bell for pick up the gas.
My wife use the pot for you flower and that dry .
She say , what make you with this pot man?
nothing nothing .
Possibly was impregnated with Na0H and kill the plant.
|
Same with thermite
Also, if I add copper oxide to the hypochlorous acid it supposedly will decompose into HCl in solution. I think. |
meanwhile electrolysis run you have ClOH +CLH between Ph 4,5 to 7 approx, when Ph decreases You have Cl2 in solution,, Whren PH is minor to 1 Cl2
escape like gas.
http://www.sbcontrol.com/hocl.jpg
I dont professional or expert but I experimented with this.
|
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
