zombiedude1
Harmless
Posts: 36
Registered: 15-10-2015
Member Is Offline
Mood: No Mood
|
|
Water Aspirator Help
I used a 1/2hp non-submersible water pump & a 5 gallon bucket with a metal water aspirator. I get a light vacuum (don't have a guage yet) which
will barely stick to my finger, and is very uneven with its vacuum pressure.
However, if I raise the water level in the bucket to where the end of the aspirator is dipped in the water, I get an extremely strong and level vacuum
(the water pump whines a little louder though)
I read around here that the aspirator should be 6-12" above the water level, and not in it. I'm not getting much vacuum that way. Could there be a
leak, or should I continue to use it this way since it creates a strong reliable vacuum?
I'm just worried about the pump getting damaged from the load)
(Using cold tap water, no ice, and a very small addition of antifreeze)
EDIT: It's also creating enough vacuum to vaporize the water coming out of the aspirator when partially submerged.
Badly drawn example:
[Edited on 3-11-2015 by zombiedude1]
|
|
Detonationology
Hazard to Others
Posts: 362
Registered: 5-5-2015
Location: Deep South
Member Is Offline
Mood: Electrophillic
|
|
Does the pump itself work well and produce an even, consistent stream? What kind of plumbing are you using? The design of the plumbing could also
produce an uneven distribution of water through the pipe, creating a sporadic vacuum. This seems like a really neat idea.
[Edited on 11-3-2015 by Detonationology]
“There are no differences but differences of degree between different degrees of difference and no difference.” ― William James
|
|
zombiedude1
Harmless
Posts: 36
Registered: 15-10-2015
Member Is Offline
Mood: No Mood
|
|
This pump is a very cheap (but of great quality) electric ($32) centrifugal water pump & appears to have a very stable, powerful consistent
stream. Runs 370 watts, 10gpm. 1" inlet, 1" outlet, manual prime, dynamic head up to 240ft. Made of thick steel and aluminum. I lubricate it with
WD-40 before and after each use.
(http://www.ebay.com/itm/191287114408?_trksid=p2060353.m2749....)
The plumbing I decided against using PVC because I wanted to watch the water flow, maybe add a pond dye for fun.
I used thick clear vinyl (I think?) tubing (hose) for the plumbing, with a plastic reducer, down to another vinyl tube, down to the aspirator.
I have polyethylene tubing for the high vacuum pressure.
I also noticed at home depot they sell copper manifolds which could be used as a cheap vacuum manifold at only $12-25. I'm not sure if the copper is
good to use though depending on reactivity of chemicals; but it's an option.
I had an autocad design for the entire system, but I deleted it after I built this.
[Edited on 3-11-2015 by zombiedude1]
[Edited on 3-11-2015 by zombiedude1]
[Edited on 3-11-2015 by zombiedude1]
|
|
Upsilon
Hazard to Others
Posts: 392
Registered: 6-10-2013
Member Is Offline
Mood: No Mood
|
|
I may have just bought the exact same pump you describe, is it this one?
http://ebay.com/itm/New-1-2HP-Electric-Industrial-Centrifuga...
If so that's an epic coincidence
|
|
zombiedude1
Harmless
Posts: 36
Registered: 15-10-2015
Member Is Offline
Mood: No Mood
|
|
Yes, it is. It's an amazing pump for this.
Anyway, my main point of posting this thread is:
- Why do I get a strong vacuum when the bottom of the aspirator is dipped in the water reservoir?
- Why do other posts/topics claim that you should NOT do this as it creates a weak vacuum, and that you should have the aspirator 6-12" above the
reservoir?
[Edited on 3-11-2015 by zombiedude1]
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
Are air bubbles getting sucked into the pump?
|
|
zombiedude1
Harmless
Posts: 36
Registered: 15-10-2015
Member Is Offline
Mood: No Mood
|
|
I don't think so. I used a baffle to test any difference; and no difference was found.
|
|
JJay
International Hazard
Posts: 3440
Registered: 15-10-2015
Member Is Offline
|
|
I have no clue. I've seen that kind of setup before, but I usually use a vacuum pump. They aren't nearly as useful for removing cheap and nontoxic
solvents like water and ethanol, though.
|
|
zed
International Hazard
Posts: 2281
Registered: 6-9-2008
Location: Great State of Jefferson, City of Portland
Member Is Offline
Mood: Semi-repentant Sith Lord
|
|
Hmmm. What is your rate of flow like?
Personally, I come from a less eco-friendly generation. I liked to open up the tap, let the water rage through the aspirator, and shoot down at least
a couple of feet, right into my sink trap. Worked pretty good.
Could be that submersion of the bottom of the aspirator, is improving vacuum, by preventing air backflow, into the pump. The ejaculated air bubbles
being entrapped in the more viscous liquid medium, that resists "leaking" backwards. Maybe.
|
|