Metacelsus
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2537
Registered: 26-12-2012
Location: Boston, MA
Member Is Offline
Mood: Double, double, toil and trouble
|
|
Laser Safety for Raman Spectroscopy
I'm thinking about building a Raman spectroscope. What safety precautions are required for a 50 mW 532 nm laser?
What I'm planning so far:
-build an opaque, matte enclosure for the spectroscope
-test optics with a 5 mW laser, then install the 50 mW one
-wear laser absorbing goggles with optical density 5 or greater
Are these precautions adequate? Are the goggles overkill? How would the necessary precautions change if I used a higher (100 mW) or lower (25 mW)
power laser?
|
|
Sulaiman
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 3646
Registered: 8-2-2015
Location: 3rd rock from the sun
Member Is Offline
|
|
I have had 5 mW, 50 mW and 500 mW green DPSS lasers,
I felt quite safe with the 5 mW as the blink reflex is probably sufficient protection due to the eyes sensitivity to green light.
The 50mW I think would have been able to burn my retina if it hadn't died so quickly.
The 500 mW was fun but terrifying, I got rid of it after a very short while.
Don't forget that with the cheap laser pen types there is often a massive output in the infra red.
Sam's Laser FAQ is my first reference for such things
http://www.repairfaq.org/sam/lasersam.htm
and remember;
DO NOT LOOK AT LASER WITH REMAINING EYE.....
|
|
m1tanker78
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 685
Registered: 5-1-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by Cheddite Cheese ![](images/xpblue/lastpost.gif) | I'm thinking about building a Raman spectroscope. What safety precautions are required for a 50 mW 532 nm laser?
What I'm planning so far:
-build an opaque, matte enclosure for the spectroscope
-test optics with a 5 mW laser, then install the 50 mW one
-wear laser absorbing goggles with optical density 5 or greater
Are these precautions adequate? Are the goggles overkill? How would the necessary precautions change if I used a higher (100 mW) or lower (25 mW)
power laser?
|
Point #2 is a good start. You'd be surprised how a speck of dust can scatter a laser beam in unexpected ways. Treat the 5mW laser as if it were a 1/2W
to build good habits from the beginning. Always wear eye protection rated for the wavelength and highest intensity + ~10% margin you'll be dealing
with. If you're going to build a custom enclosure, include a safety switch at least for the sample compartment area. A computer/MCU/FPGA-controlled
laser is prone to glitches. Don't trust your eyes to glitches or bugs!
Sulaiman brought up a good point about the absence of IR filters in the cheap greenies.
Chemical CURIOSITY KILLED THE CATalyst.
|
|
Marvin
National Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 995
Registered: 13-10-2002
Member Is Offline
Mood: No Mood
|
|
I have a squiggle on my left eye from a 5mw green through a pinhole. I figured 200uw would be eye safe. I checked the beam for 808nm and it was much
lower than the green. I wish I'd aligned those optics with a webcam.
|
|
Texium
|
Thread Moved 22-11-2023 at 19:16 |