Arthis
Harmless
Posts: 6
Registered: 16-11-2002
Member Is Offline
Mood: No Mood
|
|
Glassware without crafting nor buying it ?
Hello everyone.
Like almost all of us, we always wanna have much glassware, and it's not always easy to obtain all you want, like a particulary condenser or whatever.
I was wondering if anyway it would be possible to use standard glass tubes and use teflon (PTFE tubes) to make them hold together.
I know that teflon is particularly resistant to corrosion and heat, and has excellent chem. properties. The fact is I'm wondering whether it could be
well suitable for making a condenser for example.
Imagine just 2 tubes, 1/3'' by 1' another 1' by 2/3'', one inside the other, and linked by a teflon cap.
But wouldn't it be damageable any way ?
That would be the easiest solution to have a lot of glassware without having to pay lots of money. Just need to buy glass tubes and teflon tube. The
first shouldn't be expensive, but the second ? Is PTFE tube expensive ?
That's all fox, have a nice day, I'm going to work.
|
|
|
IodineForLunch
Harmless
Posts: 34
Registered: 28-8-2002
Location: NJ
Member Is Offline
Mood: bored
|
|
I'm pretty sure teflon (like many plastics and polymers) has poor heat conductivity, and thus would not be suitable for a condensor.
David Hansen
I set acetic anhydride aflame.
|
|
|
kingspaz
Hazard to Self
Posts: 55
Registered: 23-7-2002
Location: UK
Member Is Offline
Mood: No Mood
|
|
poor heat conductance or not if you run say 3m of PTFE coiled into a spiral through the running water stream that should be sufficient. lower heat
conductance just means you'll need more time for the heat to be removed and thus a longer tube.
|
|
|
Organikum
resurrected
Posts: 2339
Registered: 12-10-2002
Location: Europe
Member Is Offline
Mood: frustrated
|
|
teflon and glass
One problem which may occur if glass and teflon is combined depends on the fact that teflon has a extremly high thermic expansion rate, glass a
extreme low one. So a perfect fitting stopper in a glasstube can burst the tube by heating.
On the other way this might be a perfect way to fix glass and teflon tubes together provided that the teflontube has thin walls to compense the
differences.
But anyways you can use PVC or PE/HDPE most times and this costs near nothing.
ORG
|
|
|
mick
Hazard to Others
Posts: 338
Registered: 3-10-2003
Member Is Offline
Mood: No Mood
|
|
glassware/PTFE
PTFE is great with glass over about a 50oC range. Then they start sticking. PTFE creeps, especially under vacuum and warm.
PTFE is the most chemical resistance stuff known to man.
If you heat PTFE over about 250oC you could make HF gas (possible test, put it on the corner of a tile, warm it until it just starts going clear and
white smoke, cool, if the tile is etched, its PTFE, do not inhale at this point.
|
|
|
Hermes_Trismegistus
National Hazard
Posts: 602
Registered: 27-11-2003
Location: Greece, Ancient
Member Is Offline
Mood: conformation:ga
|
|
Virgin Teflon is neither particularly easy to work nor is it CHEAP!
If you can procure borosilicate tubing, WHY not condensers?
Try LABX for wonderful used anon supplies!!!
Arguing on the internet is like running in the special olympics; even if you win: you\'re still retarded.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
