soma
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
resin flask for rotovap?
Would there be a type of resin reaction flask that can be easily used on a rotovap? I'd like to find something that can be easily and completely
scraped out (to remove resinous materials or crystals).
|
|
DJF90
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2266
Registered: 15-12-2007
Location: At the bench
Member Is Offline
Mood: No Mood
|
|
Whats wrong with a glass flask? Those for the large "20L buchis" (taking flasks 5 to 20L in size) are glass and have a neck wide enough to get your
arm in (must be about 100mm) for scraping product out, or for washing.
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
I don't quite understand the problem, if you use a 24/40 oval (recovery/rotovap) type flask, it is pretty easy to remove solids once dry. You can
even get a 29/42 joint steam duct, if you want a larger flask opening still. But if you are looking to use a 2 part flask (like a reactor pot with
removable top) on a rotovap, that would seem like a very bad idea, as very hard to balance that to rotate smoothly.
I don't get what a resin type flask is for a rotovap. I consider resin type flasks as a screw-top bottle/vessel with a frit and stopcock on the
bottom for washing resin.
http://www.chemglass.com/product_view.asp?pnr=CG-1860
|
|
bahamuth
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 384
Registered: 3-11-2009
Location: Norway
Member Is Offline
Mood: Under stimulated
|
|
Well, a rotavapor "beaker" flask might be what you are after. If it is sturdy enough to run reactions in I don't know: Rotavapor Beaker Flask
Any sufficiently advanced technology is indistinguishable from magic.
|
|
chemrox
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
Absurdly expensive isn't it? You could reduce the volume in a 1-2 L rotovap and remove the rest of the solvent in a vacuum cabinet or with a fan in
the hood.
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
Dr.Bob
International Hazard
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 2690
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
If that (Rotavapor Beaker Flask) is what you want, a lyopholyzer flask is really what that is. I have not seen them used on a rotovap, but I guess
that they could work if you are really careful. They would be heavy if filled and the rubber top might just come loose until the vacuum is well
established. I use the small ones often for drying samples inside vials on the high vacuum pump. If you want some huge ones, I have the glass jars
in 1L size, as well as a few smaller ones, but not many of the rubber lids. Those always seem to get lost or damaged.
|
|
soma
Hazard to Others
![*](images/xpblue/star.gif) ![*](images/xpblue/star.gif)
Posts: 297
Registered: 31-7-2010
Member Is Offline
Mood: No Mood
|
|
Yes - that looks like what I'm looking for. $600 is real expensive but Aldrich usually is expensive for glassware. I'll check around. Thanks.
|
|