stoichiometric_steve
National Hazard
Posts: 827
Registered: 14-12-2005
Member Is Offline
Mood: satyric
|
|
Buchi Screw Wheel 00565 needed!
I'm looking for a spare part, namely the Buchi Screw Wheel part. no. 00565 for a Rotavapor RE-111 motor. Its basically a plastic toothed wheel.
check page 16 of this manual for details:
RE-11X Manual
|
|
|
zoombafu
Hazard to Others
Posts: 255
Registered: 21-11-2011
Location: U.S.
Member Is Offline
Mood: sciencey
|
|
Contact the maker of your rotovap, im sure they will sell spare parts.
|
|
|
benzylchloride1
Hazard to Others
Posts: 299
Registered: 16-3-2007
Member Is Offline
Mood: Pushing the envelope of synthetic chemistry in one's basement
|
|
Check Buchi's Amazon store, I bought one of these from them. Expect about $100 with shipping for a new screw wheel.
Amateur NMR spectroscopist
|
|
|
Arthur Dent
National Hazard
Posts: 553
Registered: 22-10-2010
Member Is Offline
Mood: entropic
|
|
$100 for a plastic gear? I'd say this is a perfect candidate for 3-D printing... Check-out if the old gear can be scanned, retouched and reproduced, I
bet this would be less expensive.
Robert
--- Art is making something out of nothing and selling it. - Frank Zappa ---
|
|
|
stoichiometric_steve
National Hazard
Posts: 827
Registered: 14-12-2005
Member Is Offline
Mood: satyric
|
|
well yeah, it's about 50 EUR. i find that disturbingly expensive.
|
|
|
edgecase
Hazard to Self
Posts: 65
Registered: 4-11-2011
Location: Ontario, Canada
Member Is Offline
Mood: Viscous
|
|
The "screw wheel", technically in north american english, it is a worm wheel, which meshes with a worm gear on the shaft of the motor.
It looks like a manufacturing defect, either the plastic is stretched very tight or solvents have caused it to shrink. Brass or even steel would be
better since it's such a low torque application. It's not like they aren't charging enough, and have to use "cheap" plastic.
I'm going to get mine measured up, the local industrial bearing shop has a set of gear pitch gauges. I would probably spend the $100 on a Buchi
original, except that based on the number of people with problems, it seems like a bad design.
http://coplanar.net/gallery2/main.php?g2_itemId=509
|
|
|
peach
Bon Vivant
Posts: 1428
Registered: 14-11-2008
Member Is Offline
Mood: No Mood
|
|
Buchi seem to love using none standard parts where there's no need to.
There are coated labyrinth seals designed for high vacuum applications at a fraction of the price of theirs.
I get a buzz off the one I have, literally... because the capacitor's can or variac in there is leaking to ground. My mates flicks the breakers. A bit
of insulation would be nice for all that money.
[Edited on 22-6-2012 by peach]
|
|
|
edgecase
Hazard to Self
Posts: 65
Registered: 4-11-2011
Location: Ontario, Canada
Member Is Offline
Mood: Viscous
|
|
So I just spent about an hour measuring up this gear, and searching for something that could be bored out on a lathe to make it better than original.
I may have found one made of Delrin (or steel, imagine! heat and solvent resistant!)
It's a bit odd, they are using a 4 thread worm gear, but instead of a matching worm wheel, they are just using a helical gear. My cheap angle finder
shows about 18 degree helix angle, 48 teeth, 2.6 inch O.D. 3/8 inch face width. I hassled the bearing shop this afternoon and got roughly 20
Diametral Pitch from one of their gear pitch gauges, 20 degree pressure angle.
http://www.hpcgears.com/products/helical_gears.htm
PARALLEL helical gears, Imperial(DP), 20DP, yields the attached catalog.
PSH20-48 looks like a good match, unsure if it's LH or RH. Price listed is 15 pounds sterling? I don't see a north american distributor tho ;<
Attachment: helicalgears_20dp.pdf (288kB)
This file has been downloaded 850 times
I'm unsure if Delrin is a good material for the heat/solvents, though it is great for wear against the steel worm gear. Steel gear might be just fine
too, there's almost no torque involved in spinning a flask in water or oil. Thoughts?
[Edited on 2012-6-23 by edgecase]
|
|
|
chemrox
International Hazard
Posts: 2961
Registered: 18-1-2007
Location: UTM
Member Is Offline
Mood: LaGrangian
|
|
I have motors. p2p me an I can arrange something with you. I bought a bunch of condensors, stands and motors a few years ago. I plant to assemble
rotovaps and sell them. The stand alone motors are "R" types and I have a couple of R-11 stands. You could pull the gear out of a motor I have that
needs to be re-packed with grease.
"When you let the dumbasses vote you end up with populism followed by autocracy and getting back is a bitch." Plato (sort of)
|
|
|
spankyetal
Harmless
Posts: 23
Registered: 24-7-2017
Member Is Offline
Mood: No Mood
|
|
Buchi worm gear new or repaired
the gap damage in the worm gear face is a common occurrence. 66% of used R-111 drives had these damages or gaps, As of 2020 Buchi sells them for
$75.00. But there is a $120.00 minimum.
You can reach Buchi US to get their downloadable order form to order a new gear at:
ordermanagement@buchi.com or fax to 302-652-8777.
You can place an order through your local Distributor such as Fisher Scientific or VWR.
Repairs can be kept below $25.00 using a clay mold, epoxy resin and Dremel grinding touch-up. So far so good.
TextText
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
Maybe an epoxy putty like milliput would be good for this?
|
|
|
Heptylene
Hazard to Others
Posts: 319
Registered: 22-10-2016
Member Is Offline
Mood: No Mood
|
|
Maybe you could make a new tooth from thick plastic plate using a jewelers saw and some files? For $100 it's worth the effort.
|
|
|
Dr.Bob
International Hazard
Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
There is someone on here who made me some replacement gears, I will ask him to check with you.
|
|
|
OldNubbins
Hazard to Others
Posts: 136
Registered: 2-2-2017
Location: CA
Member Is Offline
Mood: Comfortably Numb
|
|
Looks like this thread was necrotized, but for future reference, I have some replacement gears I can send for the price of shipping or they can be
ordered less than $15 each from BMC3D. I also have the 3D model if you want to print your own.
|
|
|
johnsonnamedborris99
Harmless
Posts: 3
Registered: 11-12-2018
Location: over here
Member Is Offline
|
|
Quote: Originally posted by OldNubbins  | | Looks like this thread was necrotized, but for future reference, I have some replacement gears I can send for the price of shipping or they can be
ordered less than $15 each from BMC3D. I also have the 3D model if you want to print your own. |
i have been looking for this worm wheel for mine too. could i get a copy of the file? if you still have another one you are willing to sell i will
take it off your hands ?
just another politically incorrect canceled culture
|
|
|
MOF guru
Harmless
Posts: 2
Registered: 2-3-2022
Member Is Offline
|
|
| Quote: Originally posted by OldNubbins | | Looks like this thread was necrotized, but for future reference, I have some replacement gears I can send for the price of shipping or they can be
ordered less than $15 each from BMC3D. I also have the 3D model if you want to print your own. |
We have the same problem with our Buchi rotavap.
Can anyone advise which exact type of helical gear it actually is from BMC3D?
Many thx in advance!
|
|
|
Dr.Bob
International Hazard
Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
That design was for a R-114 I believe. If you are in the US, he might be willing to ship you the part for postage and such. If not, I might have
some spare parts that would work, but I will be out the next week or so. If you are in the US and can't find the part, send me a note, and I will
get back when I can.
|
|
|
MOF guru
Harmless
Posts: 2
Registered: 2-3-2022
Member Is Offline
|
|
Thanks for your fast reply. I am looking for one for RE-111. From the manual it is part no. 00565. I am located in Germany/Switzerland, hence it would
probably be easier to exchange the size/particular type (e.g. Order number/Description) or the even the 3D Model of the helical gear and I will search
for it here in Europe. As you have shown already, it is commercially available, although it is definitely „special“. Many thanks in advance for
all your help!
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
