Ramdough
Harmless
Posts: 12
Registered: 5-8-2011
Member Is Offline
Mood: No Mood
|
|
Help finding epoxy to seal mmo anodes in housing
I am building a membrane electrolysis cell for making sodium hypochlorite from salt water. The cell housing will be PVC and I have some titanium mmo
expanded sheets. The cell will have slight water pressure on it due to the water height in my brine tank.
Anyone have any suggestions for sealing to the mmo coating? I plan on running the sheared edge of the mmo out of the PVC cell an epoxying the gap so
that only the mmo coating is in liquid.
Thanks in advance.
|
|
|
Ramdough
Harmless
Posts: 12
Registered: 5-8-2011
Member Is Offline
Mood: No Mood
|
|
Anyone there?
I am sure someone her has some ideas. I was considering Scotchweld 2216 grey or tan. I have used it before with some success with bonding to
titanium. All of the electrode assemblies that I have seen use a white looking epoxy. Anyone know what that white epoxy is?
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
Hypochlorite is prepared by electrolysis without the use of a membrane.
Cells shouldn't be pressurised as hydrogen is evolved during the oxidation.
Electrodes should be closely spaced for efficiency.
Cell temperature should be kept low to prevent chlorate formation and the cell can be an open container because little chlorine will escape.
And sealing with glue shouldn't be necessary . . .
|
|
|
dann2
International Hazard
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
I have used stuff from the car accessory shop. It is polyester resin and it is used in conjunction the fiber glass to fix car panels.
The polyester resin is mixed with some hardner. It seems to stand up well to Chlorate cells. It also wets the MMO well and forms a good seal. Its a
viscous liquid that pours easily (like molasses)
|
|
|
Ramdough
Harmless
Posts: 12
Registered: 5-8-2011
Member Is Offline
Mood: No Mood
|
|
Quote: Originally posted by hissingnoise  | Hypochlorite is prepared by electrolysis without the use of a membrane.
Cells shouldn't be pressurised as hydrogen is evolved during the oxidation.
Electrodes should be closely spaced for efficiency.
Cell temperature should be kept low to prevent chlorate formation and the cell can be an open container because little chlorine will escape.
And sealing with glue shouldn't be necessary . . .
|
The system I am building uses a membrane. The the brine solution is fed to only one electrode while pure water and sodium hydroxide is fed to the
other. The products of chlorine and sodium hydroxide are combined later outside of the cell. This allows me to make sodium hypochlorite without
adding brine to my product. Also the electrodes should stay cleaner.
I need an epoxy because the cell will be below my brine tank and will have hydrostatic pressure on it.
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
| Quote: | | The products of chlorine and sodium hydroxide are combined later outside of the cell. This allows me to make sodium hypochlorite without adding
brine to my product. |
The reaction of chlorine with alkali in the cold; Cl<sub>2</sub> + 2NaOH -> NaCl + NaCLO + H<sub>2</sub>O produces NaCl,
obviously, so your cell would seem a waste of time and effort when you can buy ordinary bleach which contains only hypochlorite and alkali.
Using a membrane is self-defeating . . .
Evolved H<sub>2</sub> must be allowed to escape, so a closed
cell is out of the question . . .
I think you should further familiarise yourself with the reactions involved.
|
|
|
Ramdough
Harmless
Posts: 12
Registered: 5-8-2011
Member Is Offline
Mood: No Mood
|
|
The system is centered around a membrane cell. One side takes in brine solution and produces chlorine which is used later. The other chamber produces
sodium hydroxide. In a separation chamber, hydrogen gas is vented off. .....
I am duplicating a comercially available system that works. I could try to sketch it out, but not today.
What I am trying to find out is how to seal the edges of my mmo material that have been sheared.
|
|
|
hissingnoise
International Hazard
Posts: 3940
Registered: 26-12-2002
Member Is Offline
Mood: Pulverulescent!
|
|
A diagram would certainly help, or better, a link to the system you're intent on replicating . . .
|
|
|
dann2
International Hazard
Posts: 1523
Registered: 31-1-2007
Member Is Offline
Mood: No Mood
|
|
"What I am trying to find out is how to seal the edges of my mmo material that have been sheared."
If you are worried about the Ti metal being attacked where there in no MMO, (at the sheared edges) fear not. Thats what Valve metals are all about.
They will form a self protecting Oxide coat if exposed to the electrolyte (as an Anode).
They are 'self sealing', 'self healing' or whatever you like to call it.
Dann2
|
|
|
Xenoid
National Hazard
Posts: 775
Registered: 14-6-2007
Location: Springs Junction, New Zealand
Member Is Offline
Mood: Comfortably Numb
|
|
I would stay away from epoxies and other glues for sealing MMO electrodes, they always breakdown eventually!
Spot weld some bent Ti straps to the MMO and use Ti bolts (possibly with "O" rings) through the walls of the container. Ti bolts are available from
some bike shops, engineering shops and online (Google).
I discussed this in detail in the following thread on making a salt water chlorinator for a swimming pool.
http://www.sciencemadness.org/talk/viewthread.php?tid=16144
|
|
|
Ramdough
Harmless
Posts: 12
Registered: 5-8-2011
Member Is Offline
Mood: No Mood
|
|
Patent 1
And
Patent 2
I am not exactly copying either of these. I am using the concepts to make something I think is better.
Please feel free to comment now that it is more clear what I doing.
Most people on this forum probably know more about electrolysis than me, so I appreciate any help. My expertise is making things. A friend of mine
has a full machine shop and a welder. I plan on making my system with all parts outside of the tank so that it is easier to service them. I have an
arduino with Ethernet that I plan to interface to an orp and Ph sensor as well. I hope monitor the whole system through my home server.
I hope that is enough info to get the wheels spinning.
From what you all are saying, I am thinking I might either do the spot welded sheet metal approach or just tig weld a hex head bolt to the mmo sort of
like patent 1.
Does anyone have any input on the design of the chamber that combines the chlorine and sodium hydroxide?
Thanks in advance
|
|
|
Ramdough
Harmless
Posts: 12
Registered: 5-8-2011
Member Is Offline
Mood: No Mood
|
|
Anyone there?
Just checking to see if anyone has any comments on my last post.
I appreciate the help from the group.
|
|
|
magnus454
Hazard to Self
Posts: 57
Registered: 28-2-2007
Location: Clear Lake City, TX
Member Is Offline
Mood: No Mood
|
|
JB weld or Polyester resin (bondo resin)
History is repeating itself.
|
|
|
Ramdough
Harmless
Posts: 12
Registered: 5-8-2011
Member Is Offline
Mood: No Mood
|
|
From what I learned on this forum, I no longer plan on using epoxy.
I still would appreciate help with the design of the chamber that mixes the chlorine gas with the sodium hydroxide.
I am thinking of a design similar to a co2 down flow type system like those used in aquariums.
Any thoughts?
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
