ManyInterests
National Hazard
Posts: 934
Registered: 19-5-2019
Member Is Offline
|
|
stopcock on pressure equalized addition funnel is stuck. Help?
Last week I pulled out my brand new pressure equalized addition funnel for a series of ammonia synthesis. My ammonia synthesis was a great success and
I ended up with 1000ml of 24% ammonia solution. After I was done with that, I decided to wash out the funnel and I left it to dry.
I was afraid that the stopcock on it was going to be a little too easy to pop out, so I kept it with the rubberband that it came wrapped in. I put it
in the open position and washed out the hole, but I didn't roll the stopcock around.
Now I find that it is completely shut. I was told that I need to heat it up with a heat gun to loosen it and give it a few taps with a rubber knife
handle. I did that, but it did nothing. I read that potassium hydroxide might be an adhesive...
As of right now, I am going to try to boil the bottom part of my funnel in hot water. Any help?
 
|
|
|
ManyInterests
National Hazard
Posts: 934
Registered: 19-5-2019
Member Is Offline
|
|
OK guys, I just fixed it... no need for further action. I just put the end of the funnel in a pot of water and boiled it for a while. After a brief
bit of drying, it got loose. It's all fine now.
|
|
|
arkoma
Redneck Overlord
Posts: 1763
Registered: 3-2-2014
Location: On a Big Blue Marble hurtling through space
Member Is Offline
Mood: украї́нська
|
|
Quote: Originally posted by ManyInterests  | | OK guys, I just fixed it... no need for further action. I just put the end of the funnel in a pot of water and boiled it for a while. After a brief
bit of drying, it got loose. It's all fine now. |
Exactly what i was just getting ready to suggest!!
"We believe the knowledge and cultural heritage of mankind should be accessible to all people around the world, regardless of their wealth, social
status, nationality, citizenship, etc" z-lib
|
|
|
ManyInterests
National Hazard
Posts: 934
Registered: 19-5-2019
Member Is Offline
|
|
It works good for my CO2 generator now. I am bubbling through the left over liquid, as urea and potassium hydroxide can have some potassium carbonate
and bicarbonate made as a by product. I am bubbling a huge amount of CO2 (1000g of baking soda and 3l of vinegar), into the left over liquid after
dissolving it. I already boiled what was left to near dryness to get rid of whatever bits of ammonia that were left. The CO2 should convert what is
left into carbonate.
|
|
|
Dr.Bob
International Hazard
Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Glad it worked OK. I have had many stuck stopcocks like that, usually heat or sonication works, but best to take the joint apart when not in use and
grease it well. PTFE stopcocks can be better, but they tend to get scratched and leak, as well as not work well with some chemicals.
|
|
|
Sir_Gawain
Hazard to Others
Posts: 457
Registered: 12-10-2022
Location: [REDACTED]
Member Is Offline
Mood: Stable
|
|
What chemicals would attack PTFE? I recently ordered a sep funnel and decided on a PTFE stopcock over a glass one because I heard the glass ones could
be a headache.
“Alchemy is trying to turn things yellow; chemistry is trying to avoid things turning yellow.” -Tom deP.
|
|
|
ManyInterests
National Hazard
Posts: 934
Registered: 19-5-2019
Member Is Offline
|
|
Very few chemicals attack PTFE as far as I know. I got a funnel with a glass stopcock because the Chinese lab glassware company only had that
available on their aliexpress store.
Most things will not attack glass, except for hydroflouric acid. But I have no interest in that compound, so I am not worried. I learned now what I
need to do in using/maintaining my funnel. When cleaning, remove it to dry and only reinsert it when everything is fully dry again.
|
|
|
Dr.Bob
International Hazard
Posts: 2750
Registered: 26-1-2011
Location: USA - NC
Member Is Offline
Mood: No Mood
|
|
Bromine and some strong bases can slowly attack PTFE, among a few others. It is a small number of harsh chemicals. PTFE ones are much easier to
use than glass, so only rare occassions need glass. You do need to be gentle on PTFE, leave the stopcock loose when not in use to avoid creating a
dimple where the hole is.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
