blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Hacking a test tube
I've a fairly large text tube which I need to hack in two but I only need the 'closed' part. It's a 150 mm x 24 mm large tube, wall thickness est. 1
mm.
For a smaller tube I'd probably manage but for this size I'm sctratching my head a bit. I do have a diamond tipped lab glass cutter.
Any ideas welcome!
|
|
|
mayko
International Hazard
Posts: 1218
Registered: 17-1-2013
Location: Carrboro, NC
Member Is Offline
Mood: anomalous (Euclid class)
|
|
maybe you can slap together a glass cutting jig?
https://www.instructables.com/Simple-Bottle-Cutting-Jig/
I have also seen a method where a string is soaked in alcohol, looped around the bottle, and lit... once burnt, the bottle is plunged into cold water
and the glass cracks around the hot ring. Might not work on test tubes though, depending on the glass
al-khemie is not a terrorist organization
"Chemicals, chemicals... I need chemicals!" - George Hayduke
"Wubbalubba dub-dub!" - Rick Sanchez
|
|
|
Morgan
International Hazard
Posts: 1694
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
Thin glass tubing tends to not break evenly when scored if it is a larger diameter. Maybe a dremel and diamond disk.
https://youtu.be/CfR966lIVAE
[Edited on 17-11-2022 by Morgan]
|
|
|
Texium
|
Thread Moved
17-11-2022 at 12:44 |
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Ah. Have Dremel, will try!
Thanks!
|
|
|
phlogiston
International Hazard
Posts: 1379
Registered: 26-4-2008
Location: Neon Thorium Erbium Lanthanum Neodymium Sulphur
Member Is Offline
Mood: pyrophoric
|
|
another method is to heat the test tube where you want it to break and touch it with a cold metallic rod while the glass is still hot. The principle
is that a thermal shock will start a crack to form at the desired location, which can be propagated around the tube by repeated heating/cold metal
cycles until the tube breaks. Possible advantage over the Dremel might be less glass dust.
[Edited on 18-11-2022 by phlogiston]
-----
"If a rocket goes up, who cares where it comes down, that's not my concern said Wernher von Braun" - Tom Lehrer |
|
|
j_sum1
Administrator
Posts: 6320
Registered: 4-10-2014
Location: At home
Member Is Offline
Mood: Most of the ducks are in a row
|
|
I have never had much success with the string/alcohol/plunge in water method on a bottle. I have not tried it for a TT.
It seems that the heating from the flame is not very uniform and not necessarily concentrated in a specific region to induce the thermal shock.
I have not tried this on a test tube, but I would expect it to be more difficult with a smaller diameter and with borosilicate.
You might try using a nichrome wire wrapped around the circumference. You can position it as needed, hit the switch and then plunge the TT into water
after heat has been applied.
Whatever you do, a grind on a sanding wheel or heating the end in a flame would be a sensible second step to remove the sharp edge.
|
|
|
Herr Haber
International Hazard
Posts: 1236
Registered: 29-1-2016
Member Is Offline
Mood: No Mood
|
|
Molten NaOH should do the trick as long as you dont need really smooth edges. But these you can proably fix with the Dremel.
Just dip the part you want gone in the lye.
Cackling like a madman as the glass melts is optional but I would 
The spirit of adventure was upon me. Having nitric acid and copper, I had only to learn what the words 'act upon' meant. - Ira Remsen
|
|
|
Morgan
International Hazard
Posts: 1694
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
This would be impractical and not worth trying but it came to mind as a way to eat/attack and maybe crack borosilicate glass test tubes.
https://youtu.be/ztrquSMI1tk
https://youtu.be/GE-NkVqUiHs
https://youtu.be/cFGejaYqM-c
|
|
|
Morgan
International Hazard
Posts: 1694
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
If you skip to the 1 minute 40 second mark there's a good example of "hacking a syringe" quite nicely with a dremel.
https://youtu.be/UtaECKAkS-E
|
|
|
blogfast25
International Hazard
Posts: 10562
Registered: 3-2-2008
Location: Neverland
Member Is Offline
Mood: No Mood
|
|
Dremel is definitely my method of choice, to be tried 'shortly'.
Drizzling molten lye seems (potentially dangerous) overkill.
|
|
|
Texium
Administrator
Posts: 4579
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
When you do the dremel method, make sure to keep the bit and cutting surface under water to cool and lubricate it, and go slowly. Several years ago I
had to drill a hole through a test tube using a dremel diamond bit, and that was key to success.
|
|
|
Morgan
International Hazard
Posts: 1694
Registered: 28-12-2010
Member Is Offline
Mood: No Mood
|
|
Something like this at the 6 minute mark with water helps avoid cracking and you won't overheat the diamond bit or blade either. I have an extension
for my dremel a little more electrically safe when using water. With a lathe to spin a test tube or tubing, that luxury offers quite a bit of control
too.
https://youtu.be/sRVrDTMOsII
|
|
|
Junk_Enginerd
Hazard to Others
Posts: 251
Registered: 26-5-2019
Location: Sweden
Member Is Offline
|
|
I do this a bit for glasswork purposes. Scoring and breaking, or heating, is very unlikely to turn out well. There's a small chance you get a clean
break, but it's just that: chance. Very unpredictable for diameters >10 mm or so.
Abrasion is the way to go. A dremel and diamond bit can work, but it requires a good dremel and a good tool bit. If both the chuck and the
bit aren't very well centered and smooth, the run out you get will result in a situation where you're kind of smashing the glass with the tool every
revolution. That obviously tends to crack things.
If you want the best chance of a good result, a diamond hand file is the way to go. It'll take a few minutes, but with a light touch you won't be
subjecting it to any large and sudden forces that start up any cracks, and you'll have a clean and crisp cut.
|
|
|
SplendidAcylation
Hazard to Others
Posts: 203
Registered: 28-10-2018
Location: Starving in some deep mystery
Member Is Offline
Mood: No one I think is in my tree.
|
|
I used a diamond jigsaw blade to score a test tube in order to break it, and it worked very well
|
|
|
Admagistr
Hazard to Others
Posts: 363
Registered: 4-11-2021
Location: Central Europe
Member Is Offline
Mood: The dreaming alchemist
|
|
Quote: Originally posted by blogfast25  |
I've a fairly large text tube which I need to hack in two but I only need the 'closed' part. It's a 150 mm x 24 mm large tube, wall thickness est. 1
mm.
For a smaller tube I'd probably manage but for this size I'm sctratching my head a bit. I do have a diamond tipped lab glass cutter.
Any ideas welcome! |
The best is a Dremel with a small diamond disc! I used the discs from the DIMAPA brand, not the Dremel brand. I have cut a large quartz reactor with
them,absolutely no damage and even cut the crucible from a larger sapphire tube to the exact length.The cut is thin,the surroundings don't crack and
the accuracy is very good.
https://www.dimapa.cz/50mm-diamantovy-kotouc-maly-10-ks-120-...
[Edited on 24-12-2022 by Admagistr]
[Edited on 24-12-2022 by Admagistr]
[Edited on 24-12-2022 by Admagistr]
|
|
|
CRUSTY
Hazard to Others
Posts: 139
Registered: 5-6-2016
Location: Nearby
Member Is Offline
Mood: High-Order
|
|
| Quote: Originally posted by Texium | | When you do the dremel method, make sure to keep the bit and cutting surface under water to cool and lubricate it, and go slowly. Several years ago I
had to drill a hole through a test tube using a dremel diamond bit, and that was key to success. |
And don't forget to wear a dust mask.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
