Housane
Hazard to Others
Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline
Mood: Let’s make
|
|
DCM
Hi I am wondering if ethyl acetate could be used as a direct DCM replacement as DCM becomes increasingly hard to find for extractions like caffeine
from tea.
Housane
Green QD's so far
Feel free to correct grammar or incorect knknowledge. We are all learning.
|
|
|
DavidJR
National Hazard
Posts: 908
Registered: 1-1-2018
Location: Scotland
Member Is Offline
Mood: Tired
|
|
This is too vague to answer. It will probably be suitable for some uses but not for others. So no, it is not a "direct replacement", but for
extracting caffeine from tea, it might well work.
|
|
|
Housane
Hazard to Others
Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline
Mood: Let’s make
|
|
Ok, for extractions like caffeine and others with a DCM solvent would normally be possible with ethyl acetate
Green QD's so far
Feel free to correct grammar or incorect knknowledge. We are all learning.
|
|
|
Steam
Hazard to Others
Posts: 238
Registered: 25-3-2014
Location: Minnesota
Member Is Offline
Mood: Triple Point
|
|
One of the main issues with EtAc is that it can degrade into ethanol and acetic acid under certain conditions. As long as you avoid those conditions
and trace amounts of ethanol and Ac acid are not detrimental then you should be good to go. If you think DCM is hard to find, try getting a hold of
carbon tetrachloride via OTC sources.... :d
DISCLAIMER: The information in this post is provided for general informational purposes only and may not reflect the current law in your jurisdiction.
No information contained in this post should be construed as legal advice from the individual author, nor is it intended to be a substitute for legal
counsel on any subject matter. No reader of this post should act or refrain from acting on the basis of any information included in, or accessible
through, this post without seeking the appropriate legal or other professional advice on the particular facts and circumstances at issue from a lawyer
licensed in the recipient’s state, country or other appropriate licensing jurisdiction.
|
|
|
Housane
Hazard to Others
Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline
Mood: Let’s make
|
|
Quote: Originally posted by Steam  | | One of the main issues with EtAc is that it can degrade into ethanol and acetic acid under certain conditions. As long as you avoid those conditions
and trace amounts of ethanol and Ac acid are not detrimental then you should be good to go. |
What conditions do I need to avoid is it alklinity, acidity or heat
Green QD's so far
Feel free to correct grammar or incorect knknowledge. We are all learning.
|
|
|
Tsjerk
International Hazard
Posts: 3032
Registered: 20-4-2005
Location: Netherlands
Member Is Offline
Mood: Mood
|
|
Acid in combination with water and alklinity in general. Heat is no problem in normal extractions, the solvent just boils off.
Just realize ethyl acetate dissolves a lot of water (3%) that has to be taken care of before you evaporate it to isolate your product. Also ethyl
acetate is pretty soluble in water (8%).
Always make sure you use saturated NaCl instead of plain water when working with ethyl acetate.
|
|
|
Housane
Hazard to Others
Posts: 127
Registered: 3-9-2018
Location: Worcester, England
Member Is Offline
Mood: Let’s make
|
|
| Quote: Originally posted by Tsjerk |
Acid in combination with water and alklinity in general. Heat is no problem in normal extractions, the solvent just boils off.
Just realize ethyl acetate dissolves a lot of water (3%) that has to be taken care of before you evaporate it to isolate your product. Also ethyl
acetate is pretty soluble in water (8%).
Always make sure you use saturated NaCl instead of plain water when working with ethyl acetate.
|
Thanks that is very helpful
Green QD's so far
Feel free to correct grammar or incorect knknowledge. We are all learning.
|
|
|
happyfooddance
National Hazard
Posts: 530
Registered: 9-11-2017
Location: Los Angeles, Ca.
Member Is Offline
Mood: No Mood
|
|
Ethyl acetate is used to decaffeinate coffee industrially, so yes.
However, caffeine is much more soluble in DCM and chloroform, so these will be much better for caffeine extraction in the lab.
Chloroform can be easily made from acetone and bleach, or isopropanol and bleach, via haloform reaction.
|
|
|
Texium
Administrator
Posts: 4619
Registered: 11-1-2014
Location: Salt Lake City
Member Is Offline
Mood: PhD candidate!
|
|
For extractions, ethyl acetate is generally a suitable replacement (as long as significant acidity or alkalinity are avoided, as noted by previous
posters). The only other issue with it in that application is that since it's less dense than water, performing multiple extractions is a bit more
cumbersome than it is with DCM.
Things get more complicated if you want to make the swap for use in chromatography. For normal phase chromatography, ethyl acetate is a much more
potent eluent than DCM. In my experience, eluting a compound with 1% of ethyl acetate in hexanes or petroleum ether will give similar results to
eluting with 10% DCM in hexanes or petroleum ether. Therefore, if you were following a procedure where DCM/hexanes is used for a column, you would
want to reduce the percentage tenfold to use ethyl acetate in its place, and it may not go as smoothly if it's super non-polar compounds that you're
trying to separate.
|
|
|
![[*]](images/xpblue/default_icon.gif){kind=icon}
